Digital Fault Recorders
record out of limit electrical power system events.
See Also: Fault Recorders, Transient Recorders, Disturbance Recorders
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 24 Channels, 24 Single-Ended Inputs
DN6.442-24
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
PXI 32 Channel I/O, High Side Driver
40-413-001
Digital I/O Module
A 32 channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only (shown here), alow side only and a combined high and low side each capable of driving 2A loads. Eachoutput is fully protected against over-voltage, over-current and thermal overload,ensuring robust and reliable operation in the toughest test environments. For highside voltage driving the high side voltage source is supplied from an external voltagesource, permitting the module to drive high capacity loads without impacting thePXI chassis power supply.
-
Product
PCI-4065, 6½-Digit, ±300 V, PCI Digital Multimeter Device
779770-01
Digital Multimeter
The PCI‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
8-Ch Relay And 8-Ch Isolated Digital Input PCIE Card
PCIE-1760
Digital Input PCIe Card
8 opto-isolated digital input channels with counter/timer function8 relay actuator output channels2 opto-isolated PWM outputsProgrammable digital filter function for DIJumper selectable dry contact/wet contact input signalsUp event counters for DILED indicators to show activated relaysPattern match interrupt function for DIChange of state interrupt function for DIBoardID switch
-
Product
Digital Input Board
VME-1128
Digital Input Board
VME-1128 is a 128-bit High-Voltage Digital Input Board with Built-in-Test. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297) with the following mnemonics: A24:A16:D32/D16/D08 (EO): Slave: 39/3D:29/2D Form factor: 6U
-
Product
Digital Channel, 10 MΩ Input, ±25 V, 8 Channel
CX1152A
Digital I/O Adapter
The CX1152A Digital Channel provides 8-channel digital trigger for the CX3300 Device Current Analyzer series, which is useful when a low power device with digital I/Os is evaluated. Only the CX3324A mainframe has the interface of this product. The input impedance of each channel is 10 MΩ in order to minimize the load current from the digital channel.
-
Product
Handheld Digital Multimeter, 3 ½ Digit
U1232A
Digital Multimeter
Ergonomic shaped 6K counts DMM with flashlight, low input Z mode and continuity visual/audio alerts. Keysight Remote Link Solution enabled.
-
Product
FPGA Mezzanine Card
FMC168
Digitizer
The FMC168 is a digitizer FMC featuring eight ADC channels with 16-bit resolution and 250Msps sampling rate per channel.With a flexible clock generation and distribution scheme, the FMC168 allows control of sampling frequency and analog input gain through serial communication with a carrier card.
-
Product
Transcoding Card
VEGA-3310
Digital Input PCIe Card
2-ch 4Kp60 or 8-ch real-time 4:2:2 10bit HEVC,AVC & MPEG-2 encode, decode & transcodeUltra-low latency supportLess than 35W power consumptionSimple-to-use API and example code for FFmpeg and GStreamer multimedia frameworks
-
Product
PCIe 12-Bit, 6 GS/s, Gen3 Digitizer
EON Express CompuScope
Digitizer
The GaGe EON Express CompuScope PCIe Gen3 digitizer board features unprecedented speed and resolution in a 6 GS/s streaming digitizer with 1.75 GHz bandwidth and PCIe data streaming rates up to 6 GB/s.
-
Product
NI-6584, 16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
781290-01
Digital I/O Adapter
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter
-
Product
33/60 GHz Dual Electrical Channel Module
N1040A
Digital Input Module
The N1040A is a dual electrical channel plug-in module for the N1000A DCA-X mainframe and provides two electrical channels with maximum bandwidth of 33 or 60 GHz, based on the option selected.
-
Product
REM-11152, 16-Channel (Input), 24 V, 2-, 3-, 4-Wire Digital Module for Remote I/O
784743-01
Digital Module
The REM‑11152 is a digital input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11152 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM‑11152 features 2‑, 3‑, and 4‑wire spring terminal connection methods, a built-in power supply for sensors, and an adjustable filter time to improve measurement quality. You can use inputs as counters or standard digital inputs.
-
Product
Handheld Digital Multimeter, 4.5 digit, up to 800 hours battery life
U1282A
Digital Multimeter
60,000 counts resolution on dual display0.025% basic DC voltage accuracy Longer battery life up to 800 hours Certified to IP 67 for dust and water protection Tested to withstand a 3-meter (10-ft) drop Programmable via USB (Download Programming Guide here)CAT III 1000 V/ CAT IV 600 V overvoltage protection Vsense for non-contact voltage detection Square wave output for generating pulse width modulation (PWM) signal Frequency counter Low pass filter
-
Product
PXI 16-Channel 4-Bus 2A Fault Insertion Switch
40-197A-002
Fault Insertion Unit
This 16-channel fault insertion switch is primarily intended for routing simulated fault conditions in automotive and aerospace applications involving the reliability testing of safety critical controllers.
-
Product
PXIe Digitizer: 100 MSa/s, 14 bit, 100 MHz
M3100A
Digitizer
The M3100A PXIe digitizer is ideal for general purpose digitizer automated test requirements. It offers high channel density with an advanced data acquisition systems (DAQ). The optional real-time sequencing, inter-module synchronization, and graphical FPGA programming software tools expand its capability to enable a number of solutions including angle of arrival (AoA), baseband electronics designs, wireless device manufacturing and multi-channel coherent signal acquisition.
-
Product
sbRIO-9425, Non-Enclosed, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
783950-01
Digital Module
Non-Enclosed, 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The sbRIO‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The sbRIO‑9425 offers isolation between the input and output banks from channel‑to‑earth ground. Non-enclosed modules are designed for OEM applications.
-
Product
AXIe High-Speed Digitizer/Wideband Digital Receiver, 12-bit, 3.2 GS/s, 8-ch, FPGA Signal Processing
M9703B
Digitizer
Based on the AXIe standard the M9703B is an 8-channel, 12-bit digitizer/wideband digital receiver, able to capture signals from DC up to 2 GHz at 1.6 GS/s. A channel interleaving capability allows waveform acquisition at up to 3.2 GS/s with exceptional measurement accuracy. The M9703B also provides real-time data processing, large FPGA and customizable I/O interfaces. Detailed explanations can be found in the firmware options section of the datasheet.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 180 MS/s on 8 Channels, 8 Single-Ended Inputs
DN2.447-08
Digitizer
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
PXIe-6535, 32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module
780695-01
Digital I/O Module
32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module—The PXIe‑6535 can continuously stream data over the PXI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
PXIe 14 Bit High Speed Digitizer - 400 MS/s on 4 Channels
M4X.4481-X4
Digitizer
The M4x.44xx-x4 series digitizers deliver the highest performance in both speed and resolution. The series includes PCIe cards with either two or four synchronous channels where each channel has its own dedicated ADC. The ADC’s can sample at rates from 130 MS/s up to 500 MS/s and are available with either 14 bit or 16 bit resolution. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high quality signal acquisition.
-
Product
100 MHz 32-CH High-Speed Digital I/O Card
PCIe-7360
Digital I/O Module
ADLINK's PCIe-7360 is a high-speed digital I/O board with 32-CH bi-directional parallel I/O lines. Data rate up to 400 MB/s is available through the x4 PCI Express® interface. Clock rate can support up to 100 MHz internal clock or 200 MHz external clock, ideally suiting applications of high-speed and large-scale digital data acquisition or exchange, such as digital image capture, video playback and IC testing.
-
Product
8-Ch Isolated Digital Input Module
ADAM-5052
Digital Input Module
Digital input level: Logic level 0: +1 V max.Isolation voltage: 5000 VRMSPower consumption: 0.27 W (max)Channels: 8
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 2 Channels, 2.5 GS.s on 4 Channels, 1.25 GS.s on 8 Channels, 1.5 GHz Bandwidth
DN2.225-08
Digitizer
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
Digital Power Recorder
MPR-601W-01
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Applicable for single phase 2wires and single phase 3wires and *3phase 3wires and 3phase 4wires system*Wide measuring range up to 0～500V/500A*Easy data logging by USB flash memory
-
Product
NI-5772, 1.6 GS/s, 12-Bit, 2.27 GHz Bandwidth, 2-Channel Digitizer Adapter Module for FlexRIO
782097-01
Digitizer
The NI‑5772 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that can simultaneously sample two channels at 800 MS/s or sample one channel at 1.6 GS/s with over 2 GHz of analog bandwidth. You can use the NI‑5772 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 20 MS/s on 4 Channels, 4 Single-Ended Inputs
DN2.592-04
Digitizer
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 500 MS/s on 24 Channels, 24 Single-Ended Inputs
DN6.445-24
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A, Hardware Interlock
40-193A-001-HI
Fault Insertion Unit
The 40-193A-001-HI is a 7-Channel Fault Insertion switch with hardware interlock and one fault bus, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
Product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 400 MS/s Digitizer on 4 Channels, 625 GS/s AWG on 4 Channels
DN2.828-04
Digitizer
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
