Thermal Simulation
Model heat generation and conduction.
-
Product
Thermal Shock Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Chamber provide the sudden temperature changes between extreme cold and extreme hot from -65℃ to 150℃ (customized available), specially for environmental stress screen test of the industries that rely on thermal testing, such as component, board electronic assemblies, defense, material stress, consumer products etc. The thermal shock test can cause faulting or cracking by the expansion and contraction on the products, indicates the hidden manufacturing defects. Bell’s Thermal Shock Chamber ensure you to launch qualified product to the market.
-
Product
Infrared Thermal Imaging
JOHO640CM_A00
-
Wuhan JOHO Technology Co., Ltd
OHO640CM_A00 is a high resolution 640x480 uncooled long-wave thermal imaging core. It is especially designed for OEMs. With lightweight and compact design, low power consumption and standard interface, it is very easy to be integrated into end-user products, such as portable surveillance thermal camera, UAV, thermal sight etc.
-
Product
Aircraft Simulator
ePlane PC
-
Pneumatic connections Ps, Pt and AoA (option)High accuracy, high resolutionSelectable pressure units: hPa; mb; in Hg; mmHg; ft; m; kts; km/h, ft/min; and Mach number and needle equipment visualisationSoftware executable under Windows 2000 and XPUSB cable for PC connection
-
Product
Bypass Diode Thermal Test System
-
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
Product
Circuit Breaker Simulation Device
PSS01
-
PSS01 is the circuit breaker simulator，which can conduct circuit breaker simulation to test the whole secondary relay scheme together with relay test set. It is very good accessory for protection relay test kit to avoid complicated software programming to finalize the same test.
-
Product
Thermal Camera for Drones
FLIR Vue Pro
-
Designed for professional use, FLIR Vue Pro is more than a thermal camera, it is a thermal measurement instrument and data recorder that adds tremendous value to your sUAS operations and services.
-
Product
Target simulators
-
Simat simulator is an advanced hardware simulator capable to simulate in infrared range several targets on quasi uniform background. In detail Simat simulator is a modular image projector capable to simulate in infrared range variable intensity, variable angular size, variable spectrum, spatially and temporally dynamic airborne type targets on quasi uniform background. Basically the aim of Simat to enable simulation typical airborne targets like aircrafts or helicopters for infrared imaging sensors used for surveillance of these targets. Optionally Simat can be modernized to enable simulation in both IR and UV/visible ranges as the projectors are built using broadband reflective optical elements.
-
Product
Solar Simulator (JIS AAA)
PEC-L12
-
●A compact power supply box allows installation on a desktop●The irradiation direction can be freely rotated 360 degrees●A 5cm square optical filter can be attached●Quiet shutter sound (equipped with a low-noise shutter)
-
Product
Solar Simulation
-
Sciencetech solar simulators produce high intensity, uniform illumination on a target area. Typically, high power solar simulators use an ellipsoidal reflector to capture light from an arc lamp source inside the reflector, an arrangement that results in a light pattern with a bright outer region and a dark center. This non-uniformity is un- acceptable in many solar simulator applications and as a result, forces many of our solar simulator competitors to use designs involving diffusers to reduce the non-uniformity. This results in a reduction of intensity and a dis- tortion of the spectrum on the target area.
-
Product
High Speed Thermal Printer
6041
-
• RS232C serial interface via a 6-pole RJ12 socket• Tested to comply with FCC Standards• Designed for use with Associated Model 6044 and similar devices• Four AA Batteries included• Imported
-
Product
PCB Thermal Analyzer Software
CoolitPCB
-
Powerful and highly affordable CoolitPCB enables PCB designers to do their own board level thermal analyses. Electrical engineers now can predict the thermal behavior of their designs and pinpoint optimum component placement on their boards. There is no need for CFD expertise; CoolitPCB's intelligent user interface steers the user through the solution process. But users shouldn't be fooled by this simplicity. Under the hood is the Coolit's robust, proven and advanced computational engine, that has been successfully used in thousands of design projects.
-
Product
Multi-Domain Simulation
-
Every product engineering team deals with questions in the virtual prototyping phase, many of these covering multiple engineering domains. ESI's Visual-Environment multi-domain modelling allows these teams to work together in a single user environment, around a single core compute model. This multi-domain simulation environment has the capacity to integrate all virtual prototyping problems across CAE domains. In addition, its user-friendly interface and automation features empower engineering teams to be ever more productive!
-
Product
Model Based Design and Simulation
-
Requirements validation through simulation and autogeneration of embedded systems
-
Product
ESD Discharge Simulator
Model 9910 PurePulse/PinScan
-
Model 9910 PurePulse / PinScan is used to determine the ESD susceptibility level of electronic devices up to ±4kV. PurePulse generates ESD pulses up to 4kV for testing electronic devices for susceptibility to Electrostatic Discharge (ESD) using HBM, MM and HMM models. PinScan provides automatic sequencing of ESD testing of up to 128 pin devices, applying a discharge, thenperforming a curve-trace test to identify a failure.
-
Product
PXI/PXIe LVDT/RVDT/Resolver Simulator Module
41-670-XYZ-AABBCC
Simulator
The 41/43-670 range is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. Available with up to four banks, each bank is capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
Product
Oxygen Sensor Tester And Simulator
7650
-
Peaceful Thriving Enterprise Co Ltd
This device is designed to test and to simulate 1V Zirconia and 1V/5V Titania type oxygen sensors. The simulation can help user to exam the function of the ECU. Moreover, it can analyze the type of connection wire.
-
Product
Thermal Abuse Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Thermal abuse test chamber is suitable for standard IEC 62133-2017, UL 1642 and GB 31241-2014.
-
Product
Thermal Data Logger
51101 Series
-
It is a general requirement to record temperatures, voltages, currents, and many physics quantities during research, product development, productions, and quality assurance processes. The number of record channels can be a simple one to several complicated set of hundreds. Thermal/multi-function data loggers are prefect solutions to serve for these measurement and tracking needs.
-
Product
Rain Penetration And Thermal Shock Tester
RAST
-
This is a user-friendly, three-in-one test stand for your operating convenience. Internal and external shock tests as well as rain penetration tests are all important for determining the quality and durability of your products and meeting all relevant international standards.
-
Product
Custom Solar Simulation
-
Atlas Material Testing Solutions
Solar heat load effects are critical with respect to product functionality, operational performance, thermal management, noise and dimensional stability. Therefore, any new product made from different materials and components should be tested under solar environmental conditions representative of those locations in which it will exist - anywhere ranging from the heat of the Australian Outback to the frigid climate of arctic regions.
-
Product
Thermocouple Simulator Module for SLSC
Simulator
Bloomy’s 8-Channel Thermocouple Simulator Module provides eight channels of galvanically-isolated thermocouple simulation and simulates types E, J, K, M, N, and T thermocouples. High-precision digital-to-analog converters which are isolated from each other and from system power provide sub-microvolt resolution and accuracy. Built-in switching provides open-circuit faults as well as switching to system calibration resources.
-
Product
Solar Simulator Testing Kits
-
Solar Light’s Solar Simulator Testing Kits are designed for scientific and industrial professionals who want everything they need to begin testing all in one comprehensive package.
-
Product
Thermal cameras
-
SKF Condition Monitoring Center
Using an SKF Thermal Camera is a proactive way to help you detect problems before they occur, increasing uptime and improving safety. They allow you to be able to visualise potential problems, invisible to the naked eye, by presenting a picture of the heat distribution of an asset. The thermal image, presented on a large LCD screen, shows you where the temperature is either too hot or too cold allowing you to pinpoint potential problems fast.
-
Product
MAGNESIUM ANODE SIMULATOR
CS-1
-
The CS-1 portable Magnesium Anode Simulator is an ideal DC current source that will allow the user to see what the addition of a magnesium anode on their system will do to Pipe to Soil measurements and other C.P. tests.
-
Product
Real-time RF Channels Simulator
RF-LiveSim
-
Covering a frequency range from 50 to 900 MHz, RF Live Simulator can emulate RF channels propagation modes in real-time for a signal bandwidth from 20 kHz to 20 MHz (gaussian noise, multipath, Doppler and frequency drift tools). RF-LiveSim is a cost effective solution for intense automatic non regression tests at the physical layer level. RF-LiveSim includes 1x RF input and 1x RF output ports, and provides a complete set of channel models, either for fixed or mobile propagation environments. Whatever the standard, any type of receiver can be tested. Thanks to its real-time process, from your basic original signal, RF-LiveSim can perform, for instance, efficient regression testing of LTE solutions to check the good behavior and the limits of your receiver when multipathes, Doppler and Gaussian noise are applied.
-
Product
Thermal Microscope Stage For Petri Dish
TS-4SMP
-
With our TS-4SMP Thermal Stage for Petri Dish, a specimen on a microscope slide or culture dish can be maintained at any temperature between -20°C and +60°C. Setup is easy, takes little time, and the controller will regulate the stage temperature to within +/-0.1°C. The collar on the stage is designed to accommodate a 35mm 'Nunc' petri dish. The collar may also be removed for use with slides.
-
Product
Crash Simulation Systems
-
The crash simulators are capable of reproducing a wide range of standardized and user-defined crash tests including advanced applications such as side impact and vehicle pitch simulation. Instron’s acceleration sled systems are used for the development and approval of vehicle safety systems, vehicle parts and also for the investigation of solids and structures during crash events.
-
Product
Barometric Pressure Simulation
SimBARO
-
Embedded and Integrated GPS/Inertial navigation systems require an altitude reference data input provided by a barometric pressure altimeter to reduce vertical plane errors inherent within inertial systems. Spirent’s SimBARO product offers a simulated source of barometric pressure altitude data and is available as an add on to SimINERTIAL, Spirent’s Inertial Measurement Unit (IMU) and Embedded GPS/Inertial navigation system (EGI) test tool.
-
-
Product
Axle Load Simulators
-
In case vehicles need to perform a brake test in laden condition, one could consider to use a load simulator. In that case the vehicles can come to the brake test unladen; the load simulator will add the required load to the axles.
