Fiber Optic
Field of optic fiber application.
See Also: Fiber, Fibre, Fiber Optic Test, Reference Transmitters
-
Product
Optical Voltage Probe
400-02
-
Srico’s optical voltage probe uses advanced, proprietary optical chip technology to achieve precise, interference-free measurement. Our sensor and optical fibers are made of dielectric materials. This facilitates a high degree of isolation between the voltage test point and the instrumentation system ⎯ at a safe distance of 100 meters and more. This system senses, measures, and transmits electrical data very accurately.
-
Product
Microwave Wideband APD-TIA Receivers
MR12 (40KHz~18GHz)
-
Hangzhou Huatai Optic Tech. Co., Ltd.
MR12 series microwave wideband optical receiver, adopts high Sensitivity APD diode and limiting amplifier, within bandwidth of 40KHz~18GHz, they are featured with excellent linearity, high responsibility and superior flatness of the RF response in both, power and phase. They provide an outstanding linearity fiber optical communication for analogue wideband microwave application. Due to avoidance of using expensive coaxial cable or wave-guide, there will be no limitation in transmission distance, which improves the signal quality and reliability of the microwave communication. They can be widely applied in microwave communication system such as remote wireless, timing and reference signal distribution, telemetry, measurement and delay line etc as well as 10Gb/s high speed communication system.
-
Product
Optical Fiber 1×4 Switch
OFSW - 1 × 4
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×4 is a 1×4 prism optical switch. It can support 1 optical fibers input and 4 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
Product
PXI Dual 2 x 2 Insert/Bypass Switch FC/PC
40-860-122
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Fiber optic active antennas / field probes
EFS-105
-
The EFS-105 is the first in a family of fiber-optic active antennas & E-field probes. The field distortion caused by the probe head is nearly zero due to the exceptionally small probe head and the all-optical signal transmission and power supply. This gives an invaluable advantage for near field measurements and measurements close to metallic parts.
-
Product
Group3 Control
-
Group3 Control is a fiber optically linked control system using distributed I/O modules called Device Interfaces, or DIs. A DI is positioned at the point to be controlled and the appropriate I/O boards added to it from the list below.
-
Product
Optical Connector Inspector
OCI-20BN
-
OCI-20BN is a portable optical fiber connector inspector for checking fiber and connector end-face cleanliness, ideal for bench top and fiber optic network installation technicians to eliminate error caused by poor quality or improper cleaning.
-
Product
Fiber Optic Connectors
-
TE's fiber optic connectors accommodate 10G Ethernet — with the capacity to handle next-generation 40G and 100G when needed — without the severe distance limitations of copper cable. Easy to maintain in the field, and reliable when operating in harsh environments, our fiber optic cable connectors offer significant size and weight savings. Our broad portfolio includes several fiber optic connector types including standard fiber connectors, LC connectors and SC connectors.
-
Product
Ethernet To Fiber Optic Converters (Point To Point)
-
Our rugged, industrial-grade, point-to-point Fast and Gigabit Ethernet to fiber optic converters work in pairs to extend 10/100/1000M Ethernet signals over long distance. These Fast and Gigabit Ethernet to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode and single-mode, and ST, SC, FC, and SFP connectors.
-
Product
Fibolocator
-
Fibolocator is an innovative device for measuring and characterizing breaks and other backscattering-causing faults in optical fibers. Time-resolved correlation reflectometry is the principle on which the device is based. It analyzes the backscattered light like a pulse OTDR, but unlike such OTDRs, cw laser diodes are used. The requirements for the test signal and the complexity of the system are low, which leads to very low costs for OEM subsystems.
-
Product
Managed Ethernet Switch with L2/L3 Layer Support and Fiber Optic Option
ES2
-
Ethernet Switch module, ES2 provides up to 16 10/100/1000 Base-T 1 Gb ethernet ports. Additionally, there is one 10/100/1000 Base-T maintenance port interface, one RS-232 maintenance/console port interface, and a Fiber-Optic channel with four 10 Gb ports. It also provides numerous L2 and L3 networking, quality of service (QoS) and security features available as described below.
-
Product
OTDR
AV6416
-
Hangzhou Softel Optic Co., Ltd.
AV6416 palm OTDR is the newest instrument designed for testing FTTx network. It's mainly used to measure the physical characteristics of optical fiber under test, such as the length、the transmission loss and the splice loss etc.. It can also locate the faults or breaks of optical fiber. It's widely applied in the manufacture, construction and maintenance in optical fiber communication system.
-
Product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass, Single-Mode, 9/125 Fiber, LC Connectors
42-860A-432
Switch Module
The 40/42-860A-432 is a PXI/PXIe triple insert/bypass switch with LC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
ARC Fusion Splicer
FBT-19S
-
Shanghai Fibretool Technology Co.,Ltd.
FBT-19S Optical Fiber Fusion Splicer is small size optical fiber fusions splicer, mainly used for fusion and protection of common communications fibers. The rich functionality and ultra-low splice loss make the splicer adaptive to fiber splicing in various environments. It is featured with small size, light weight, high reliability, greater environmental adaptability, dust-resistant, water-resistant and shock-resistant. Multiple fusion modes and heating modes are available to meet diversified customers’ demands. Fiber loading becomes more convenient and accurate thanks to the ceramic V-groove of high precision, which is easy for clean and maintenance. The splicer is capable of dual-directional fusion. The monitor is a touch screen delivers fresh designed graphical interfaces, which are simple for operation. The modular pluggable lithium-ion battery of large-capacity ensures long-time field operations. The auto environment compensation system greatly improves adaptability of the splicer to hostile environments, so that low-loss splice can be remained consistent in various environments.
-
Product
Fiber Switches
-
Piezo-electric driven switches are especially designed for fast switching – measured in milliseconds. Piezo actuators enable the optical switch to couple optical fibers with an accuracy of a few microns. The piezo driven optical switches are available fiber core diameters of 50 µm up to 600 µm.
-
Product
2.5mm Visual Fault Locator
3105
-
Anfkom International Co.,Limited
The 3105 Pen type VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network. It includes:Finding the breakpoint, poor connections, bending or cracking in fiber optic cables.Finding the faults of OTDR dead zoneEnd-to-end visual fiber identification
-
Product
Light Source
FiberPal OT-3000
-
The OT-3220/3221 is designed for a high performance stabilized laser source, especially in practice for FTTX networking installation and maintenance fieldworks environment requirements. It is usually applied as stable laser sources for wide range of optical testers and tools in optical fiber cabling and transmission systems.
-
Product
Up/Down Converters
-
Over the years, In-Phase Technologies has received many requests for frequency conversion units. Our standard product line of frequency converters includes models that operate from RF though 60 GHz. Many options are available to complement our standard offerings. We also have a series of RF-to-optical converters that allows customers to send RF and microwave signals over fiber optic cables.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber
40-852A-218-HI
Multiplexer Module
The 40/42-852A-218-HI is a PXI/PXIe 8-channel multiplexer with SC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Multi-Mode, 62.5/125 Fiber, SC Connectors
40-855A-222-M
Multiplexer Module
The 40/42-855A-222-M is a PXI/PXIe dual 2-channel multiplexer with SC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Datacenter 12 MPO Fiber Optic Testers & Switches
-
Optical Wavelength Laboratories
MULTI-PAIR FIBER LINKS are becoming more common than single pair fiber links for high speed communications, especially in data center environments. OWL DataCenter 12 Series test kits automatically test 12-fiber MPO cables and links without requiring cassettes or fanout cables. Higher density connections (i.e. 24, 36, 48, 60 or 72) can also be tested with MPO break-out cables.
-
Product
Ultrafast Fiber Optic Photodetectors
DXM Series
-
The DXM series of Ultrafast Detectors are fiber-coupled photodetectors with wide wavelength ranges, as shown in the plot to the right, that are designed to be used for a variety applications. Each provides a high-fidelity electrical output pulse in response to an optical input pulse, and their clean impulse responses have full width half maxima (FWHM) down to 15 ps.
-
Product
EDFA
SPA-08-XX
-
Hangzhou Softel Optic Co., Ltd.
1550nm series multi-outputs optical amplifier gain spectrum bandwidth between 1545~1563nm, adopt high reliability multimode pump laser and double clad fiber, the unique APC, ACC and ATC circuit, the max output power can reach to 40dBm, one device and replace the original several to dozens traditional EDFA, can greatly save the cost and maintenance expense, improve the stability of the network operation, high output power 1550nm optical amplifier is playing an increasingly important role in the continuous extension of the optical fiber network, providing a flexible and low-cost solution for the wide coverage of CATV system in large and medium-sized cities.
-
Product
MIL-STD-1553 Fiber Optic Bus Extender
FO-1553
-
Avionics Interface Technologies
Extends MIL-STD-1553 bus access to over 1 mile for remote access - Dual redundant, single and dual stream options available - Both Transformer and Direct coupling modes supported - Uses fiber optic 1.0625 Gbps data rates for low latency over long distances - Optical signaling is not affected by electrical noise and interference - Simple and easy to use solution, no software setup or configuration required - Ideal for applications where test equipment is separated from UUT
-
Product
PXI Dual 2x2 Insert/Bypass Switch SC
40-860-222-M
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Connectors
-
Through our Hypertac, IDI and Sabritec technology brands, we supply application-specific, high-reliability electrical interconnect solutions from highly integrated assemblies to microminiature connectors and spring probe contacts. The core of our advanced interconnect solutions is our contact technologies: Hyperboloid, Tortac, Spring Probe, High Speed, Edge Card, Fiber Optic, EMI/EMP, High Power and High Temperature.
-
Product
Epoxy Injecting Machine - EIM-280
-
Shanghai Fibretool Technology Co.,Ltd.
1, Injecting Epoxy Adhesive into ceramic ferrules for fiber optic connectors.2, High Accuracy to control epoxy dosage.3, Easy to adjust output pressure and injecting time.4, With hand touch switch and foot switch.5, Compact for production line.
-
Product
Mini Fiber Node – RF Receiver & Return Path Transmitter
MX700
-
MAXCOM MX700 products deliver RF , return path services or both, over a fiber optic infrastructure to home, businesses, schools /universities, hospitals, parks, and MDUs . It provides optical-to-electronic conversion in a single, cost effective design.
-
Product
Pulsed Transmitter
-
Built to operate in harsh environments, the Pulsed Transmitter unit provides radar installation decoy protection in a compact footprint and is powered by a Dewey Generator.The unit is comprised of a power supply, power amplifier, signal generator and antenna, with a fiber optic command and control interface providing throughput speeds capable of 1.25 G bits/sec via 1310 nm, single mode, ruggedized fiber.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Single-Mode, 9/125 Fiber, SC/PC Connectors
42-850A-214
Multiplexer Module
The 40/42-850A-214 is a PXI/PXIe 4-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
