Waveform Monitors
View a video signal's electronic pattern.
-
Product
Continuous Emission Monitoring System
CEMS
-
CEMS, the “Environmental Eye” for Source Emissions.A Continuous Emission Monitoring System (CEMS) is an integrated system to measure fuel flow, dust, and concentrations of air pollutants such as SO2, NOx, CO, CO2, THC and O2 in accordance with the applicable regulations for the emission source.
-
Product
CO2 Monitor
T5000
-
Although carbon dioxide is invisible and odourless, increased CO2 content in the room leads to fatigue and decreased mental concentration.
-
Product
Monitoring Solar Panel Strings, DC 30A, Φ10mm
CTF-60-10DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Compact, Space-saving, Low Cost DC Current Sensors.・Split-core type, easy to apply to existing circuit.・Easy to use by unipolar +5V power supply.・High speed responsibility – less than 10μsec. 0 rated primary current.・Suitable for monitoring solar panel strings.
-
Product
Voltage Monitoring, Timer Delay-on -off, 4 Pole
MTDV4 Relay
-
Plug-in electronic voltage monitoring relay with optional delay-on and delay-off timer function and four change-over contacts. The delay time is adjustable with a lockable knob (either delay-on or delay-off, the other delay is fixed). The relay can also be supplied with fixed time delays (no knob). The pull-in voltage and drop-out voltage are both adjustable via internal screws. The relay can also be supplied with a fixed pull-in and drop-out voltage. Suitable for monitoring DC voltages.
-
Product
Monitor SDR Boards
-
Multiple Access Communications Ltd.
MAC Ltd’s MONITOR product family includes a number of software-configurable digital signal processing platforms intended for use in radio frequency (RF) receiver and transceiver applications. The MONITOR products are available in assembled printed circuit board (PCB) form for integration into larger systems. They also form the basis of MAC Ltd’s CatchAll™ radio products. In addition to the standard products listed below, MAC Ltd is happy to discuss the customisation of existing products and/or the development of new bespoke hardware and software.
-
Product
Device Current Waveform Analyzer, 1 GSa/s, 14/16-bit, 4 Channel
CX3324A
Waveform Analyzer
The CX3324A is a 4-channel model for engineers and researchers who need more than two channels for current waveform measurements at one time. Using a passive prove interface (CX1151A) with a current sensor (CX1101A, CX1102A, CX1103A) enables power measurements. The bandwidth and the memory depth per channel are option and can be selected from 50 MHz, 100 MHz and 200 MHz, and 16 Mpts, 64 Mpts and 256 Mpts, respectively. Upgrade products for both bandwidth and memory depth options are also available for customers who need more performance after purchasing the product. 8-channel digital channel (CX1152A) can be used with this 4-channel model so that you have more flexibility of triggering.
-
Product
Storage Resource Monitor
-
Storage resource management reporting for health, performance, and capacity of multi-vendor storage
-
Product
Graphical Waveform Editor and Instrument
PI-PAT
-
Much more than just a visualization tool, PI-PAT is a full-fledged graphical waveform editor that allows you to spend more time testing and less time programming. PI-PAT doesn't require any programming experience or complicated syntax. Just draw or type patterns directly into the pattern window. Move a clock edge by dragging it. Adjust integration times by entering a single number. Change the output to your DUT by clicking the Update button. You'll never have to wrangle DSP or FPGA code with PI-PAT.
-
Product
CMM AutoQAL & CMM Continuous Mercury Monitoring Systems
-
Continuous Mercury Monitoring systems, the CMM and CMM AutoQAL, are TÜV and MCERTS certified solutions for continuous mercury monitoring from hot, wet and corrosive gas streams of industrial processes, such as waste incineration, cement production and powerplants. Gasmet offers a full CMM solution package which consists of a system, lifetime service and support, documentation and training, and our expertise.
-
Product
Intelligent Application and Service monitoring
Datadog
-
With turn-key integrations, Datadog seamlessly aggregates metrics and events across the full devops stack.*SaaS and Cloud providers*Automation tools*Monitoring and instrumentation*Source control and bug tracking*Databases and common server components*All listed integrations are supported by Datadog
-
Product
Battery Monitoring
-
Eagle Eye Power Solutions’ advanced battery monitoring systems are designed to optimize performance, enhance safety, and ensure compliance. Explore reliable solutions for real-time monitoring and maintenance of critical power systems.
-
Product
Permanent PQ & Energy Monitoring Products
-
Compact monitoring solution that combines PQ monitoring (with waveform recording) and 4 quadrant energy monitoring in one instrument.
-
Product
DC Power Supply With Scope, Arbitrary Waveform Generator, And Automotive Application Features Bundle
E36154AGVX
DC Power Supply
The Keysight E36154AGVX consists of a Keysight E36154A DC power supply, a Keysight E36150ADVU Scope View and arbitrary waveform generation (AWG) capabilities, and a Keysight E36150ATMU Automotive Standards Testing Capabilities with Enhanced Programming Speed, ISO Preset Library, Playback Simulation and E-Logging features. The E36154A includes single-output and auto-range capabilities, 30V, 80 A, 800 W, and LAN and USB interfaces.
-
Product
Real-Time Content Monitoring System
ORION
-
Interra Systems' ORION is a real-time content monitoring system that enables service providers to deliver error-free, superior quality video. ORION provides real-time monitoring of IP-based infrastructures that looks at all aspects of video streams such as QoS, QoE, closed captions, ad-insertion verification, reporting and troubleshooting. ORION performs critical monitoring functions on hundreds of services simultaneously from a single platform, providing an operator with a single point of visibility and access to important information such as, status, alerts, alarms, visible impairments, error reports, triggered captures and more. ORION effortlessly monitors streaming content scaling single to multiple monitoring units/ sites across different geographical locations.
-
Product
Zero Gas Generator - Calibration of Ambient Air Monitoring Systems
ZNV-7
-
HORIBA Europe’s Zero Gas Generator ZNV-7 has been developed to check the zero point and dilute the span gas sources in order to carry out the calibration of ambient air monitoring systems. The increasing sensitivity of ambient air analyzers is required by strict official guidelines, which demands pure and dry air in a sufficient quantity at constant pressure.
-
Product
Fume Hood Monitor
FHM10
-
Fume hoods are a primary source or protection in laboratories. Face velocity measurements are often used to gauge the performance of a fume hood’s ability to contain and exhaust hazardous chemicals. By accurately measuring face velocity and alarming on unsafe conditions, TSI’s FHM10 Fume Hood Monitors provide a high level of fume hood safety. And, the FHM10 helps users comply with standards and regulations set forth by OSHA, NFPA, ANSI Z9.5, and SEFA, calling for monitors to be installed on fume hoods.
-
Product
Thin Film Composition and Thickness Monitor
P-1000
-
The Precision P-1000 readily analyzes compound thin films utilized in semiconductor, superconductor, magnetic and applications.
-
Product
27” LED-Framed Gaming Monitor With Touchscreen
GM-270S
Gaming Monitor
ADLINK’s GM-270S LED-framed gaming monitor is specially built for casino gaming applications, such as video lottery terminals and slot machines. The GM-270S features 10-point PCAP touch screen and addressable LED frame is ideal as the interactive screen of a slot machine, making players feel more engaged in the game.
-
Product
12-bit Waveform Digitizer
ATS9353
-
ATS9353 is a low-noise 12-bit waveform digitizer board designed for OEM customers. It can sample two analog inputs at rates up to 500 MS/s.
-
Product
1.25GS/s 16Bit 1GS Mem 12CH Arbitrary Waveform Generator
P12812B
Waveform Generator
The Proteus P12812B, is a 1.25GS/s, twelve channel arbitrary waveform generator packaged in a 4U, 19” standalone box with a 9” touch screen and on board PC , offering technologically advanced options and configurations that integrate the ability to transmit, receive and perform digital signal processing all in a single instrument. The P12812B offers industry leading performance Including an innovative task oriented programming, real time data streaming, fast feedback loop for environment dependent waveform generation and user customizable FPGA for application specific solutions.
-
Product
Monitoring
7880SA
-
Quintech Electronics and Communications Inc.
The 7880SA module is Evertz' spectrum measurement and analysis module providing high end performance at a low price.
-
Product
CMAS Analyzers and Field Monitors
-
Backed by at least one of the 8 corrosion sensor patents wholly owned by Corr Instruments, our nanoCorr analyzers and field monitors are widely used for online and real-time localized and general corrosion monitoring. These ultra-high precision instruments measure extremely low currents in the pico-ampere levels, which can be translated into a corrosion rate as low as a few nanometers per year, in some applications (PDF). Our analyzers and monitors are based on the patented coupled multielectrode array sensor (CMAS) technology which measures the flow of electrons from corroding electrodes to one or more cathodes.
-
Product
USB Arbitrary Waveform Generators
-
The U2761A is a 20MHz function generator that offers 10 standard waveforms plus pulse and arbitrary waveforms generation capabilities. It uses the common non-proprietary standard high-speed USB 2.0 interface that simplifies connectivity allowing users to set up and configure their test swiftly with the plug and play feature.
-
Product
Partial Pressure Monitor for RGA
PPM100
-
Stanford Research Systems, Inc.
The PPM100 is a stand-alone controller/monitor for SRS residual gas analyzers. It measures partial pressures from SRS RGAs and total pressure from up to four capacitance manometers. Graphical output is available on a touchscreen LCD display.
-
Product
Hydrogen Penetration Monitoring System
MS3112
-
The Hydrogen Penetration Monitoring System™ provides a method for directly measuring the rate of hydrogen migration through a vessel or pipe wall. This method actually measures the penetration current set up by the hydrogen as it moves through the steel. By sensing and recording this data directly from the pipe wall, this system offers valuable data which can only be indirectly inferred by other methods.
-
Product
PDS Cutter Dredger Monitoring Software
-
TELEDYNE PDS for Cutter Dredges is designed to the requirements of the dredge operator to carry out their job more efficiently. The operator has a real time overview of the dredger with the top and side views displaying the vessel outline, ladder, and cutter head along with the surveyed depths, design, and dredged depth.
-
Product
Analog Waveform Development and Analysis Software
WaveEasy
-
WaveEasy is an interactive analog waveform editor software tool for creating and editing analog waveforms. To view or edit existing waveforms, you can open or save files using various file formats including WaveEasy, ASCII or text (txt, csv, prn), or the NI-HWS (hws) format which is used by many instrument drivers.
-
Product
Water Monitoring Modules
-
Unidata offers a wide range of instruments to suit the measurement of conductivity, evaporation, water depth and temperature. In addition to those water instruments, Unidata also offers Starflow QSD ultrasonic Doppler velocity and depth SDI-12 Instrument.
-
Product
Compact Data Logger: Monitoring Temperature, RH and Dew Point
HD208
-
The data loggers of the series HD208 are compact instruments for monitoring temperature, relative humidity (RH) and dew point temperature. Usable in a wide spectrum of applications, are available in various models (with or without LCD display):
-
Product
Concrete Measuring and Monitoring System
IQM-Meter
-
Designed specifically for monitoring and analyzing fresh concrete, the IQM Module is programmed with the required Equivalent Age of the concrete under test. Once this preset maturity number is reached, a visual indicator will flash continuously, providing an effective, automatic indication that the concrete has reached the desired level of maturity.
