Load Cell Simulators
generate a precise mV/V signal to assure load cell amplifier, tester, readout and display set up.
See Also: Load Cell Test, Load Cells
-
-
Product
Resistive & Capacitive AC Load Bank
RCD
-
RCD AC load banks are used to test the REAL working condition of UPS, rectifier, inverter and etc who are loaded by non-linear or electronic load with non-constant resistance such as computer, networking equipments and etc. Through the accurate detection of its output and power quality, users could avoid the inadequate loading capacity or cause pollution to power grid, so as to guarantee supply security. JUNXY RCD load banks leading power factor loads are created to debug power supply system parameters such as its crest factor test.
-
Product
SolarIV Series Solar Cell Current Voltage Measurement System
SlarIV
-
SolarIV IntroductionOne of the key measurements needed for photovoltaic devices in the measurement of their I-V characteristics. Through measuring the I-V curves the user can determine physical performances of devices such as photo-electric conversion efficiency, fill factors and so on. Such data is important for reliable work in research and quality inspection. ZOLIX supply the SolarIV system and the most perfect, professional technical support.
-
Product
Load & Fatigue Testing
-
DATASYST Engineering & Testing Services, Inc.
Due to variations in types and levels of load and fatigue exposure, DATASYST works with each client to determine the best possible test plan to capture the information and issues that may be present in application.
-
Product
Spring loaded type sample mounting board
SPCB
-
Mount samples on SPCB board without bonding wires.Spring loaded clamps helps to move probe pin easily x, y, z direction.Gold plated Non-magnetic phosphor-bronze constructionContacts on sample’s four point corner by soldering materials, such as InSn may still be required for good ohmic contact.
-
Product
Load Cell Amplifier
-
Xiamen Elane Electronics Company, Ltd
: 0-50 degrees. Humidity: 30 to 80 percent, non-condensing.Power Supply Requirements:Power Supply voltage: 9 volts DC.Operating current: 5mA, plus bridge current.Bridge Input:Excitation voltage: 5 volts.Bridge Type: Full Wheatstone Bridge.Voltage Output Range: From 0 volts to 4.3 volts.
-
Product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
150W Electronic Load
EL63150B
-
Features:*Number operation and control*LED display with high definition and high contrast, rich display information*Easy operation of knob encoder switch*Basic load function: constant current, voltage, power and resistance*Multi units used to multiple load ability*Short-circuit test*Battery test*Dynamic test*Multi parameters measured in the list*Remote voltage measurement*Panel and exterior trigger function*Protection function: over-voltage, over-current, over-power, over-heat, polarity connection in reverse*10 sets of parameters memorized and loaded, and automatically loaded on turning on the instrument*Intelligent fan control*Key lock and knob lock functions
-
Product
Advanced Thermo-Mechanical Simulators for Materials Testing
Gleeble 3000 Series
-
Comprises three distinct thermo-mechanical simulator models, each engineered to address specific materials testing requirements while maintaining the precision and reliability.
-
Product
Parallel Simulation Engine
RocketSim
-
Complementing compiled-code simulators, Cadence® RocketSim™ parallel simulation engine eliminates functional verification bottlenecks by speeding up simulation using commonly available multi-core servers.
-
Product
CAN & LIN bus Custom Test & Simulation Software
CanX
-
Schleissheimer Soft- und Hardwareentwicklung GmbH
CanX is the custom testing and simulation software for CAN and LIN bus for specific user groups. The run-time software is designed to execute predefined or automated tasks in testing, work preparation, production, repair or project management.
-
Product
Regenerative Grid Simulators
-
Chroma Systems Solutions, Inc.
Rigorous testing to industry regulatons and standards for the safe operation of on-grid products.
-
Product
Digital Control DC Electronic Load
IT8200 Series
-
IT8200 series economical programmable electronic load,with the highest cost/performance ratio and small size, they are widely used in production testing lines and maintainance lines etc. Resolution 1mV/1mA ensures the accurate measurement result. IT8200 series has programmable performance, and can quickly recall 4 * 40 group memory data, panel function keys and display interface is clear, provide customers with simple operation program, easy and fast to complete a variety of complex tests. The series has CV, CC and CR mode, and short circuit test function, it is the most cost-effective electronic load products.
-
Product
AFDX® / ARINC 664 Test And Simulation PCIe Module
PCIe-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
DC Electronic Load
EE30181A
-
The EE30181A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current
-
Product
Portable Solar Simulator
XES-50S2
-
By making some improvements, it became a more user-friendly, extensively feature-rich model with better performance.
-
Product
TDL Network Simulation
-
Curtiss-Wright Defense Solutions
The need for realistic and effective military training simulations is fundamental to prepare warfighters for the challenges they may face on the field. The TCG portfolio of advanced tactical data link solutions enables the creation of configurable high-fidelity simulations, both real-time or scripted, of the industry’s most prominent data link protocols and standards.
-
Product
Telemetry Simulators & Test Transmitters
-
Command Data Telemetry Simulators offer a dynamic way to create or change a PCM data stream on a word by word basis on the fly. This PCM data stream can be used to modulate an FM or SOQPSK RF output at S-Band or L-Band. In addition to simulating a new telemetry stream, the telemetry simulators can play back and loop an archived data file (which can also be changed on the fly) or create pseudo-random patterns.
-
Product
Electronic Load
-
* Fully programmable, self-contained, air-cooled solid state load.* Patented design is optimized to provide ultra-low impedance operation for fuel cell testing.* Load is compatible with AC impedance or frequency response analyzers.* Interchangeable shunts for precise operation over a wide dynamic range.* Ten built-in cell voltage monitoring inputs optional. Additional voltage monitoring inputs available.* Ethernet Interface for simple configuration and expansion!* Combine with additional Fideris™ Innovator Series™ modules to create a fully-integrated,fully-automated, customized test system.* System-wide control of all Fideris™ Test System Components using FCPower™ Software,LabviewTM, or other programming language.* Integrated hardwired Run/Standby signal.
-
Product
Load Tester for D Type Durometers
-
A load tester for checking the spring load characteristics of ASKER hardness testers at the hardness readings of 25, 50, and 75.
-
Product
Programable Power Supply & Programable Electronic Load
PW-8033P
-
*DC 0~32V / 0~3A X 2 + Fix 5V/3A*Triple Output 207 VA High Power*4 Digits, 4 Display*Programable Control, 9 Memory*Built In USB Interface*Series 0~64V / 0~3A Operation
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel, Simplified Current Sink, 750 V Isolation
43-752A-901
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Test Cell System
qCf FC25/100
-
The quickCONNECTfixture with an active fuel cell area of 25 cm 2 has been an integral part of our product portfolio since 2006. The excellent properties and the patented design of the cellFixture offer enormous advantages in the characterization of cell-internal components for fuel cells and electrolysis.
-
Product
Portable Engineered Test Cell
PET
-
PET is an innovative portable engine test cell. Most test cells are designed by an architect and built of conventional materials like bricks and mortar, making the cells immovable and inadaptable to changing requirements. Emprise has developed a practical alternative to this PET a portable and modular engine and component test cell.
-
Product
Class AAA Steady State Solar Simulator
-
King Design Industrial Co., Ltd.
*Lamp average life 25,000 hours (We offer 1 year warranty including lamps)!*Spectrum Mis-match Class A, without filter! *Irradiance almost no decay within 10,000 hours!*Spectrum maintains stable during power adjustment!
-
Product
Signature Compression Only Load Button Load Cells
SLB SERIES
-
The SLB Series Subminiature load cells (Load Buttons) are offered for compression only applications where space is limited. The matching surface must be flat for ultimate accuracy. The loading diameter is slightly convex for accurate load distribution. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
Product
Full 4-Quadrant Grid Simulator
TC.ACS
-
The increasing number of alternative power sources like solar, wind driven or biological energy systems call for consistent and well demanding regulations for energy feed into the utility grid. Manufacturers of such systems have to test and to prove the compliance of their equipment. Grid simulators form an electronic equivalent circuit for the grid, but allow to vary all relevant parameters in order to test the behaviour and response of the equipment under test.
-
Product
Time-domain Field-Device-Circuit coupled simulator
EM-SUPREME®
-
Time-domain Field-Device-Circuit coupled simulator for modeling of passive structures, active components, and complete RF & millimeter-wave modules. EM-Supreme is used for EM modeling of power amplifiers, switches, filters, active antennas, and complete RF modules such as antenna-switch, switch-filter, switch-filter-amplifier, and front-end modules with no approximations.
-
Product
600W Bench Electronic Load, Dual Input 150V, 60A, 300W
EL34243A
-
Keysight’s EL30000 Series bench electronic loads consist of three models, all with a built-in data logger. The EL33133A basic performance electronic load offers an economical price, a limited range, and a single 40 A, 150 V, and 250 W input. Two performance models offer additional ranges, the EL34143A single input 60 A, 150 V, 350 W, and EL34243A dual input 60A, 150V, 600 W.
-
Product
Network Simulator
SWAT WDS
-
Alethea Communications Technologies Pvt Ltd
Alethea’s SWAT WDS Network Simulator emulates the whole Customer Premises side with one box generating up to 32 CPEs with 4 ~ 8 ethernet clients behind each CPE. This setup which mirrors actual field deployment allows transmission points to be checked in detail as soon as the access point is setup. The solution gives a calibrated measure of the User Experience expected over the deployed system.
