Automotive
Car industry or about cars.
See Also: Vehicle, V2X, Truck, Electric Vehicle, Car, Autonomous Vehicle, Autonomous Underwater Vehicle
-
Product
3-Axis AGREE Chamber Vibration Test Chamber Elevator Mechanism
-
Guangdong Test EQ Equipment co., Ltd.
Widely used in aviation, aerospace, shipbuilding, defense, electrical engineering, electronics, automotive, motorcycle, telecommunications, and scientific research industries. Designed to assess the reliability of electrical/electronic products, instruments, and equipment during transportation, storage, and operation. This integrated system combines a temperature/humidity test chamber with vibration platforms to independently conduct temperature, humidity, vibration, and combined environmental tests.
-
Product
Amp Clamp
PPDCM80
-
The Power Probe Digital Clamp Meter is an 80amp, auto-ranging clamp meter designed specifically for the automotive technician. This meter is rated CAT III 600V and can measure Volts, Amps, Ohms, Frequency and Temperature, necessary for automotive electrical testing. This meter’s diagnostic applications include (but are not limited to) Parasitic Draw, Crank Current testing and HVAC Temperature testing.
-
Product
Single Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-001
Fault Insertion Unit
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
Continuity Tester Supplied without Battery
22700
-
Use to test for continuity with power disconnected. Excellent for use on marine, recreational and general automotive vehicles. Test appliances and other electrical circuits with power off. 48" lead wire. Uses AA 1.5 volt battery (not supplied).
-
Product
Brake Fluid Tester
-
Is well designed suitable for determining brake fluid quality, developed for professional use in automotive repair shops and in servicing. Quality tested is indicated on five LEDs in terms of "percentage of water in the brake fluid."
-
Product
6-12V Heavy Duty Circuit Tester
1671
-
Peaceful Thriving Enterprise Co Ltd
Check on 6 and 12V systems.1. Locate short, ground or open circuit.2. Make it easy to find out where current is present.3. The most essential for troubleshooting automotive electrical systems.4. Checks series-parallel switch and solenoid on tractor-trailer start system.
-
Product
ASICs
-
ams has been creating unique ASIC (Application Specific Integrated Circuit) solutions in partnership with customers for over 30 years. We enable our partners to create highly differentiated products that are smarter, safer, easier to use and more eco-friendly. Our various industry experts in automotive, industry, medical and smart building are looking forward to talk to you and to define the solution which will exactly fit your needs.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 1 kV Isolation
41-752A-103
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Optics Test Systems
Front Window Scanner For Wedge Angle Measurement
-
Optik Elektronik Gerätetechnik GmbH
Scanning of complete automotive windshields to measure the wedge angle and thickness change, especially in the HUD area.
-
Product
High Voltage Battery Test System
-
The increasing use of electric drive systems both in the automotive industry and in transportation requires the development of new high-performance energy storage systems. In order to support you in the development and production of these systems, S.E.A. develops individually configurable test systems which are scalable and can be used flexibly for the respective requirements.
-
Product
Inverted Metallurgical Microscope
GX53
-
Designed for use in the steel, automotive, electronics, and other manufacturing industries, the GX53 microscope delivers crisp images that can be difficult to capture using conventional microscopy observation methods. When combined with OLYMPUS Stream image analysis software, the microscope streamlines the inspection process from observation to image analysis and reporting.
-
Product
Vector Signal Generator
SMCV100B
Vector Signal Generator
The R&S®SMCV100B vector signal generator is the first multistandard platform for automotive, broadcast, navigation and wireless applications. This makes the R&S®SMCV100B unique for use in many applications, from the lab to production and wherever different technologies meet.
-
Product
PXIe-8522, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module
787312-01
Ethernet Interface
PXIe, 4-Port, 1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8522 is a 1000BASE-T1 unshielded twisted pair (UTP) module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications that require Automotive Ethernet to test … and validate automotive electronic control units (ECUs). The PXIe-8522 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8522 also provides LEDs on the front panel to help you monitor the network link and activity.
-
Product
Coating Thickness gauges.
-
PELT gauges provide data for the precise control of exacting coating-applications including for automotive paints, wind turbine blade protective coatings, steel coil coatings, and shipping container anti-corrosion coatings. PELT gauges measure coatings on substrates including steel, aluminum, plastics, carbon fiber, composites, glass, and wood.
-
Product
Dynamometer
-
Innco Systems EMC Chassis Dynamometer Systems (sometimes referred to as a ‘’rolling road’’), used in the development and homologation for Automotive Industry, are specifically designed to be used in Anechoic Chambers.
-
Product
O.N.E. for Development
-
"O.N.E. for Development" goes beyond pure data exchange features of a generic middleware. The platform provides:- Deterministic data exchange- Distributed scheduling- Native tooling- Cloud support- Real-time capability- Many HW/SW InterfacesIt has been extensively used in in testing & validation applications within aerospace and automotive industries.
-
Product
PXI Multiplexer, Very High Power DC, 4-Channel, 40A, 14V
40-664A-001
Multiplexer Module
The multiplexer is suitable for switching heavy loads or for slave switching large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of DC voltage at high current.
-
Product
100BASE-T1 Automotive Ethernet Protocol Analyzer
100BASE-T1
-
Prodigy Technovations Pvt. Ltd.
100BASE-T1 Automotive Ethernet Protocol Analyzer is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. Automotive Ethernet interface scales up to address current and future needs of in-vehicle bus speed requirement. Need for higher-speed in-vehicle bus is increasing to support feature-rich ADAS and connected vehicle needs. Two-wire full duplex 100BASE-T1 PAM 3 signaling is the choice of interface bus to address these needs
-
Product
Clamping Force Tester
KRD102
-
KRD102 series clamping force tester is an indispensable test method for improving products into high-quality fields. It is suitable for research, development, quality control and manufacturing of electronics, electromechanical, optoelectronic, automotive, toy, packaging and other industries. It can simulate the situation that the goods in the container are clamped when they are transported from the container to the warehouse. Whether the goods are damaged due to the clamping, so as to evaluate the anti- clamping ability of the packaging.
-
Product
Kelvin Test Contactor
cCompact
-
cCompact™ test contactor offers a reduced site-to-site pitch concept enables high parallel test for power applications on strip test and pick and place handler platforms.Featuring compact Kelvin footprint with outstanding CRES stability by Denmark pin material. Automotive temperature range -60°C to +175°C. Integrated Socket Air-distribution.
-
Product
PCI-4462, 204.8 kS/s, 118 dB, 3.4 Hz AC/DC Coupled, 4-Input Sound and Vibration Device
779309-01
Sound and Vibration
The PCI‑4462 is a high-accuracy data acquisition module specifically designed for sound and vibration applications. It provides simultaneous four-channel dynamic signal acquisition with six programmable gain settings for making high-accuracy, frequency-domain measurements. The PCI‑4462 also includes software-configurable AC/DC coupling and integrated electronic piezoelectric (IEPE) conditioning to ensure precision measurements with microphones, accelerometers, and other transducers that have very large dynamic ranges. Common applications for dynamic signal acquisition devices include audio test; automotive test; noise, vibration, and harshness (NVH) analysis; and machine condition monitoring.
-
Product
Interior Wiring Testing
-
With automotive interior designs becoming more luxurious, cabin space features such as ambient lighting and seat / steering wheel controls have increased the demand for interior wiring testing. Jackmark Engineering has years of experience supplying test equipment for instrument panel manufacturers and have increased their portfolio to include all aspects of interior wire harness testing.
-
Product
Automotive Production Test Unit
GTU
-
The GTU vehicle bumper electronics tester helps engineers to ensure that the correct components are present, of the correct engineering revision and that they function as designed.
-
Product
Radome Tester
QAR50
-
The R&S®QAR50 is the ideal tool for accurately testing the quality of automotive radomes and bumpers in the automotive radar frequency range at the end-of-line (EOL). It features sufficient space to easily accommodate bulky bumpers combined with spatially resolved measurements to evaluate the homogeneity of design emblems.
-
Product
Sensors And MEMS Test
-
Easy docking and undocking of the MEMS modules to the standard test handler whether Gravity, Pick and Place or Test in StripTest in the complete tri-temp range for ambient, hot and cold (automotive certified)Easily convertible to other packagesDownscaled stand-alone engineering set-up availableGlobal support by experienced Cohu Field Service and Applications staff
-
Product
Haze Meter
HAM-02
-
Jinan Leading Instruments Co., Ltd.
HAM-02 Haze Meter is a kind of small hazer meter designed according to ASTMD1003—61(1997). It is applying to test the light transmittance,transmission haze, and reflection haze, reflectivity of transparent and semitransparent parallel level material and plasticfilms. Also it is suitable for liquid samples (water, beverage, pharmacy,colored liquid, grease) turbidity measurement. It is the basic instrument for plastic, glass products, all kinds oftransparent packaging films, colored and colorless of organic glass andaerospace, automotive glass and photographic film.
-
Product
Tracer Gas Leak Testers
-
At ATEQ, we understand how essential it is to detect hydrogen leaks as swiftly as possible. For this reason, we carry our own high-quality gas tracer equipment. One of popular tools is the H 6000, which is a multipurpose, handheld hydrogen leak detector designed to identify a broad spectrum of hydrogen gas concentrations. You can use this instrument for multiple applications like automotive and HVAC.
-
Product
Calibration Software
-
System Monitor is a software package for configuring and tuning automotive control systems. It has built-in support for motor sport systems and can be tailored to support third party control units.System Monitor not only allows you to tune data for your program versions, but also manages those versions on disk, allowing them to be located quickly for programming or modification
-
Product
Fibersim
-
Maya Heat Transfer Technologies Ltd.
The Fibersim portfolio of software for composites engineering from Vistagy, a Siemens PLM company, is used by numerous leading manufacturers in the aerospace, automotive, marine, and wind energy industries. Fibersim supports all of the unique and complex design and manufacturing methodologies necessary to engineer innovative, durable, and lightweight composite products and parts.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 1 kV Isolation
43-752A-112
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
