Automatic Test Systems
execute test program sets automatically. Also known as: ATS
See Also: Automatic Test Equipment, ATE Integrators
-
Product
Test Automation System for Driveline Testing
STARS Driveline
-
STARS Driveline is an integrated automation, acquisition and control system that provides a broad range of application functionality in a single, powerful environment. It has been designed to fulfil the specialist requirements and applications for driveline testing from simple modal testing on two or four wheel drive systems, to RLS simulation or advanced applications such as service load replication (SLR).
-
Product
MultiBeam System
FIB
-
An easy-to-use, out-lens type scanning electron microscope (SEM) equipped with a Schottky electron gun, as well as a new FIB column capable of large current processing (maximum ion current 90nA) installed into one chamber. JIB-4610F enables high-resolution SEM observation after high-speed cross-section milling with FIB, and high-speed analysis with a variety of analytical instruments, such as energy dispersive X-ray spectroscopy (EDS) that takes advantage of the Schottky electron gun delivering a large probe current (200nA), electron back scatter diffraction (EBSD) to perform crystallographic characterization, and cathodoluminescence (CLD). In addition, the 3D analysis function Cut & See is included in the standard configuration, allowing cross-section milling to be executed automatically at fixed intervals, while acquiring SEM images for each cross section.
-
Product
Benchtop Test System
300 Series Benchtop ATE
-
The Circuit Check 300 Series benchtop ATE Test Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 300 Series Benchtop ATE, test procedures can become automatic, with test steps and go/ no-go limits easily programmable in common tabular form. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
Recording System
Surveyor DFR DDR
-
The Surveyor Recording System is a DFR/DDR with local Input Modules connected to a Controller. The Input Modules are connected to the Controller by multiconductor cables. The Controller contains a single board computer running 64-bit Microsoft Windows 10® and the E-MAX Director program, for recording, storing and transferring data.
-
Product
Vision Systems
-
Our GEVA vision systems offer the performance and flexibility to inspect multiple parts, assemblies or surfaces at the same time. These systems are equipped with multi-core processors, high-speed camera ports and versatile I/O options to match your application and factory integration requirements.
-
Product
Metrology System
Echo
-
The Echo system is a comprehensive in-line metal film metrology tool for single and multi-layer metal film measurements in leading-edge logic, memory, advanced packaging, and specialty semiconductor devices.
-
Product
Macro-Vickers Hardness Testing System
LV Series
-
LECO's LV Series Macro-Vickers Hardness Testing Systems offer an affordable testing system suitable for larger, heavier samples used in welding and other demanding applications. Models include analog and digital, with options to upgrade to automatic configurations.
-
-
Product
Missile Systems
-
IES Systems is a turnkey test system solution provider with proven experience in Acceptance Test Procedure (ATP) testing, Highly Accelerated Stress Screening (HASS) and Environmental Stress Screening (ESS) testing.
-
Product
Laboratory System
EGA60
-
The next generation of multi-sample analysis systems. The EGA60 is a fully integrated system, featuring an accurate and reliable CO2 analyzer that measures CO2 to 1ppm in a range of 0-2000ppm, and measures H20 to 0.1 mbar in a range of 0-75mbars.
-
Product
Systems
-
Our systems use an open and flexible architecture to create a platform allowing integration of technology and modules with short system set-up times which result in a reduction of costs.
-
Product
Sensing System
DTS
-
Our Distributed Temperature Sensor(DTS)with operating system is designed for easy installation and management in the field.Several DTS units can be controlled remotely by Ethernet configuration.
-
Product
EMC Test System
-
An electric product might cause the malfunction to other electric appliances by discharging the emission noise from it, or is oppositely caused the malfuction by the emission noise from other electric appliances. The former is checked by the EMI test and the latter is checked by the EMS test. The international standard like the CISPR standard is provided so that such an accident should not happen, and the manufacturer must declare by themselves beforehand that their product meets the standard. The generic name of the EMI test (Electro-Magnetic Interference) of the emission measurement and the EMS test (Electro-Magnetic Susceptibility) of the immunity
-
Product
Automatic Electrical Protective Equipment Test Systems
CBC-50С (CBC-100C)
-
Automatic systems CBC-C-series are designed for high-voltage withstand testing of electrical protective equipment and insulated hand tools. The tests are carried out with AC voltage (CBC-50C: UAC ≤ 50 kVRMS; CBC-100C: UAC ≤ 100 kVRMS) at industrial frequency (f = 50 Hz).
-
Product
Computing Systems
-
Curtiss-Wright Defense Solutions
Mission computers are the heart of every platform. To ensure your mission success, our embedded computing systems are backed by decades of experience developing C5ISR, vetronics, and program-specific system solutions.
-
Product
Fully Automatic Test Machine for Ceramic Substrates
U800CCT
-
1. CCD automatic alignment, with an accuracy of ± 10μm2. Support layout test, displacement function3. The upper and lower jigs X, Y, θ are automatically fine-tuned to improve the yield4. Automatic loading and unloading of magazine5. Automatic bad marking and verification of scratches
-
Product
VFTLP+ Test System
4012
-
The Model 4012 VFTLP+™ test system was developed in early 2000 to add high speed measurements to the usual I-V plot, to measure and record the real TDDB waveform which causes oxide failure.*Accurate measurements of this waveform have finally been identified by Barth Electronics Inc. and CDM protection can now be based on known dimensional design parameters. We identify the response of your CDM protection circuits with 100ps risetime pulses which simulate the real CDM test. This is the only way with which to provide the total gate oxide threat voltage data.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
Product
Surge Voltage and Surge Current Testing Systems
-
HIGHVOLT Prüftechnik Dresden GmbH
Pulse Voltage Test Systems are used for surge testing on transformers, cables, gas insulated switchgear (GIS), arresters, and other high voltage equipment.
-
Product
Digital Battery Tester with Automatic Test
706
-
Controlled by microprocessor, simply activate the switch once and the #706 applies a precisely timed, 10 second load to the battery. The test results, “OK”,“WEAK” or ”BAD” are then displayed along with the test voltage, until the unit is disconnected. The #706 also tests charging voltage and relative starter current draw.
-
Product
Modular Battery Test System
-
This modular battery test system provides for manufacturers versatile testing possibilities. Due to modularity it allows easy configuration of battery testers for a wide range of different power levels.
-
Product
Control Systems
-
GCA leverages decades of electronics and software experience as we build control panels and PLC software that bring machines to life and orchestrate how the machine's various components work together.
-
Product
Impulse-Calibration-System
KAL1000 Series
-
The impulse calibration system KAL1000 is a modular system to perform tests on complete impulse voltage measuring systems and on digital recorders for the measurement of high impulse voltages and impulse currents. The modular design allows an optimal KAL-configuration depending on the actual application.Additional, this modularity allows to up-grade or modify and existing KAL1000 system in case of changing or additional requirements
-
Product
Sensing System
DAS
-
Our Distributed Acoustic Sensor(DAS) with excellent pattern recognition software can detect and locate the distributed thousanfs of acoustic events. Whenever any vibration or sound around its sensing fiber is detected, our DAS system will process the measured data in real-time and its pattern recognition software will recognize the types of the events, such as digging, pipeline leakage, fence breach, vehicle moving person walking. And, the detected events are reported to the alarm server to help operators take actions to protect theor facilities.
-
Product
Semiconductor Test System
-
IST Information Scan Technology, Inc.
As power modules age, their performance degrades. Proper testing and maintenance of semiconductor devices used in power switching can ensure optimal performance and prevent down-time throughout a device’s lifecycle. The IST Model 8900 Series Discrete Semiconductor Test Systems allows you to effectively identify the percent of degradation in semiconductor devices by simulating the exact current and voltage of the parameters used by devices under real operating conditions.
-
Product
Blackbody System
IR-518/301
-
Infrared Systems Development Corp.
The IR-518 Radiation Source provides an accurate, stable source of infrared radiation of known flux and spectral distribution. It can be used as a standard radiation source for the calibration of other laboratory sources, detectors, or other infrared devices requiring calibration against a standard.
-
Product
Function Test and In-Circuit Test
CT350
-
ICT test points: max 2736 CAD Data import Automatic program generator Powerful debugging tools Test coverage analysis Paperless repair station Logging- and statistic functions Full graphical functions Panel and multisite tests Fast adapter exchange High Pin Count-Interface On table optional usable shelf part.
-
Product
HV AC Voltage Test Systems
-
Fivestar HV Testing Equipment Co., Ltd.
FSHV offers three different types of AC voltage test systems, the conventional type is AC test transformer design, mainly for testing objects of medium & low capacitance products, particularly for tests requiring stable voltage even if the load changes under voltage (corona, wet & pollution tests) or when the load is inductive (like inductive voltage transformers). Another is AC resonant test systems, according to series resonance circuit XL=XC (2πfL=1/2πfC), by setting F frequency of power supply or L inductance of reactor, generate a pure sinusoidal waveform of the test voltage, and the required input power is only 1/Q. Variable frequency type operates in a frequency range from 20Hz to 300Hz, ideal for field commissioning test of power cables and GIS/GIL. Variable inductance type outputs continuous AC voltage of power frequency (50/60Hz), mainly for factory testing of high and ultra-high voltage cables, power transformers, GIS, etc.
-
Product
Automatic Flight Inspection Systems
AT-940
-
The AT-940 is a mobile and deployable flight inspection system providing high performance in the smallest possible package.
-
Product
Precision Laboratory Systems
-
With accuracy and reliability, our products set standards in the laboratory technology market.
-
Product
Electronic Test And Measurement Systems
-
Summaries, information, & tutorials about electronics test and measurement equipment & techniques.
