-
Product
Battery Test System
WBCS3000Ls / WBCS3000Le
-
Low current model8 channel battery cycler (expandable up to 128 channels)max. voltage range : ±5Vmax. current range : - Model WBCS3000Ls : ±10mA - Model WBCS3000Le : ±100mACustomized specification is available.
-
Product
12V Battery Tester
1957
-
Peaceful Thriving Enterprise Co Ltd
Voltage / battery / alternator multi tester for all 12V DC systems.
-
Product
Battery Analyzers
Beta D-50
-
*Analyzer for any type of battery.*Adjustable constant current discharge from 0 to 50 Amps.*Set for Amp-Hour capacity reading.*Accept or Fail lights Indicators for a GO/NO-GO Test.
-
Product
Vehicle Battery Charger
6435A
-
Peaceful Thriving Enterprise Co Ltd
This charger use microprocessor to monitor the charging process. Therefore it is a smart charger with protection of reverse connection, over-voltage, over-current, short circuit and over-charging. It has wide working temperature and it has IP54 protection. Cigarette lighter connector and alligator clip can be replaced for power source.
-
Product
Battery Simulator
-
The purpose of this battery impedance network (BNB) is to provide electric power to the device under test, providing a standard impedance. It has been developed for automotive tests. A resistor that emulates the internal battery resistance is implemented in the BNB.
-
Product
Battery Testers
-
Wuxi IMHOO Technology Co., Ltd.
Voltage of batteryBattery type1.5VButton Cell, AA,AAA,C,D,N3V Lithium6V Camera Battery9V 12V 15V 22.5V Power Source Not use batteryWeight 260gmeasurement 100x63x33mmPacking50pcs/CTN
-
-
Product
Battery Monitor Relay
BMR
-
The Battery Monitor Relay contains over under voltage sensors combined with positive and negative ground detection.
-
Product
Battery Module
BAT-200
-
The Battery module supplies power to a sensor, or chain ofsensors, operating in the Off-Line mode, and to sensors connectedto an RF communication module.The Battery module can be recharged by connecting it to the PC'sUSB socket via the USB module's USB cable.
-
Product
Battery Probes
-
C.C.P. Contact Probes Co., LTD.
CCP offers a variety of different high current battery testing probes.
-
Product
Battery Test Equipment
-
Improper functioning of battery systems installed in utilities, power plants, telecommunication systems, industrial applications and etc., can cause severe failures of the supported equipment and loss of critical information. Therefore, the battery test verifies their actual SOC (State of Charge) or SOH (State of Health) and prevents unwanted scenarios which could result in a significant budget loss as well as endanger of human lives.DV Power battery test equipment is able to perform the following battery measurements, using BLU and BVR devices:- Voltage (String and Cell)- Capacity- Temperature- Density of electrolyteAll of the above-mentioned measurements are performed with the highest accuracy. The advanced DV-B Win PC software enables collecting both numerical and graphical results. These features provide an easier and more efficient analysis. After the test, DV Win software generates a test report with a single click. A user can easily customize the report and save it in different formats, such as CLS, PDF, Word, or RTF.
-
Product
Battery Chargers
BAC Series
-
Battery charger BAC series is a portable and universal battery charging solution. It is primarily intended for charging Lead-Acid, Ni-Cd and Li-ion batteries from 1 V DC to 300V DC level. However, the unit can charge the string of any battery type by one of the available charge modes:IU (constant current + constant voltage)UU (constant voltage + constant voltage with a current limit)Charging modes provide a safe regulation of charging procedure and achieves fast recharge and low risk of overcharge.Variety of implemented protections, such as thermal, overcurrent, undervoltage, and overvoltage, assure the charging process will be safe for the battery and the instrument itself.A user doesn’t have to switch off the main charger in order to use BAC series charger. Just the opposite, the BAC series charger should support the main charger to speed up the process. An alternative use is to quickly recharge a battery following a discharge test.The provided display enables users to monitor all relevant information during the charging process and to adjust charging parameters and limits in real-time.The instrument offers the best power-to-weight ratio in the market, weighing only 10 kg / 22 lbs with the maximum output power of 2,7 kW.The maximum charging currents for lead-acid, Ni-Cd and Li-ion batteries, at various battery voltages, are presented in the brochure.
-
Product
HEV Battery Reconditioner
-
Battery reconditioning and cell balancing is a well understood process for NiMH batteries. The procedure was initially developed for NiCad batteries decades ago. NuVant Systems has simplified the process to bring electrochemistry to the streets. The EVc unit is a push-one-button-after-wire-up system for small shops to large vehicle operators.
-
Product
CTEK Battery Analyzer
56-925
-
The CTEK BATTERY ANALYZER tests with high accuracy the condition of all types of 12V lead-acid batteries including Wet, Maintenance Free, Ca/Ca, Gel and AGM. Easy to use it provides fast, and easy to understand results. Operating voltage range is 8–15V with a test range of 200–1200EN. Simply connect the clamps to the battery and follow the step by step instructions on the display.
-
Product
Vehicle Battery Tester
1957A
-
Peaceful Thriving Enterprise Co Ltd
This is a helpful tester for 12V vehicle battery. User is able to check the battery power level and the charging condition with various circumstances. It is also able to monitor the alternator condition by very easy procedure.
-
Product
Battery Electrical System Analyser
-
We invented the “Resistance method” which uses a series of shorting pulse to measure the voltage drop in order to calculate the plate’s internal resistance. Unlike other patented “Conductance method” which generates an AC pulse across the battery terminal to measure impedance.
-
Product
Standard 0.81 (23.00) - 4.50 (128.00) Battery Probe
CP-059-026
Battery Probe
Current Rating (Amps): 10Average Probe Resistance (mOhm): 25Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 57Full Travel (mm): 1.45Recommended Travel (mil): 40Recommended Travel (mm): 1.00Mechanical Life (no of cyles): 100,000Overall Length (mil): 221Overall Length (mm): 5.61
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, Simplified Current Sink, 750 V Isolation
41-752A-903
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Battery Analyzers for Stationary Battery Systems
-
Fluke Battery Analyzers are the ideal test tool for maintaining, troubleshooting and performance testing individual stationary batteries and battery banks used in critical battery back-up applications in data centers, telecom networks, power distribution systems and more. With an intuitive user interface, a compact design, and rugged construction the Fluke Battery Analyzers are designed to provide optimum performance, test results and reliability.
-
-
Product
Battery Monitoring System
FST-TA
-
Foresight Electronics Co., Ltd.
Continuous 24/7 on-line monitoring One CELLCHECK monitor one cell, including internal resistance, voltage and temperature Software is available to collect data from CELLCHECK Serial port with Optical isolation, meet MODBUS protocol, easy to be accessed by UPS controller Easy to install without specialized training Full resistance, battery temperature and voltage monitoring for comprehensive battery state of health analysis String current and ambient temperature monitoring
-
Product
Battery Tester
G5.BT
-
The G5.BT series is bidirectional regenerative. It was developed specifically for testing energy storage devices and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.BT series has an outstanding current accuracy of <0.02% FS, an additional high-resolution current measurement range, and a fast current rise time in the 100 μs range. Ripple modulation, an integrated safety relay for PL c according to EN ISO 13849 and a powerful CAN multi-protocol interface (1 kHz, 16 bit) as well as functions to avoid reverse-polarity problems, current surges, and unwanted deep discharges make the G5.BT series the ideal, versatile battery module and battery pack tester.
-
Product
Battery Tester
-
Shenzhen Graigar Technology Co.,Ltd.
A battery tester is an electronic device intended for testing the state of an electric battery, going from a simple device for testing the charge actually present in the cells and/or its voltage output, to a more comprehensive testing of the battery's condition.
-
Product
Lithium Battery Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Lithium battery test chambers are used to simulate various extreme conditions such as crush, impact, penetration, overcharge etc the lithium ion cells and batteries are subjected to during use, transportation, storage and disposal to determine the safety performances, tests including altitude simulation test, thermal test, vibration test, shock test, external short circuit test, impact/crush test, overcharge test, discharge test etc based on UN38.3, IEC62133, UL1642 standards. Applicable to communication products, computer products, consumer electronics, automobile power supplies and so on.
-
Product
16CH Battery Cell Simulator
Chroma 87001
-
Chroma Systems Solutions, Inc.
Chroma 87001 Battery Cell Simulator is a high precision, programmable, and bidirectional DC power source with both voltage source and current source functions. In addition, the model can be used as a multi-channel DC power supply or an electronic load as well. A single simulator has 16 channels and each of them can set voltage and current respectively via Chroma software.
-
Product
Battery Test & Automation Solutions
-
Chroma specifically developed battery cell test solution which is an integrated solution for battery cell formation & grading processes. From battery cell formation procedure to grouping process, Chroma 17900 series are customized with professional planning service which includes manufacturing flow path planning, test station/ equipment planning, test data management and so on to create high performance manufacturing capability.
-
Product
CP-059-19 Battery Probes
Battery Probe
Current Rating (Amps): 10Average Probe Resistance (mOhm): 25Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 62Full Travel (mm): 1.57Recommended Travel (mil): 40Recommended Travel (mm): 1.02Mechanical Life (no of cyles): 100,000Overall Length (mil): 276Overall Length (mm): 7.01
-
Product
Automotive Battery Testers
-
ELAK Battery Testers are high-rate discharge testers. These testers impose a load on the battery, which is equivalent to that drawn by the starter motor from the battery, while cranking the engine. The tester studies the drop in battery voltage & indicates the condition of the battery if it is capable of starting the engine or not.
-
Product
Battery Tester 12V Language
BT12L
-
The Battery Tester 12V Language (BT12L) is an inexpensive, simple and easy tool for testing automotive batteries. It has LED display that consumes very little current and will not drain the battery with repeated testing.
-
Product
Battery Tester
BAT-250
-
The Amprobe BAT-250 Battery Tester is designed for one-handed, comfortable and reliable battery measurements. The uniquely designed tester offers an ergonomic slider and a v-shaped side cradle to better hold batteries in place during testing and a contoured case shape that fits neatly in your hand. Testing your batteries has never been easier.
