-
Product
Digital Current Integrator
-
The ORTEC Model 439 Digital Current Integrator was designed to accurately measure DC currents or the average value of pulse currents such as produced by accelerator beams. It digitizes the input current by producing an output pulse for specific values of input charge. A front-panel switch permit the selection of three different amounts of charge (10–10, 10–8 or 10–6 coulomb) required to produce an output pulse. The instrument has a digitizing rate from 0 to 10 kHz to provide wide dynamic range on each setting and high-resolution readout without meter interpolation.
-
Product
1U Network Appliance With Intel Atom®C3000 Processor For SD-WAN, UCPE And Network Applications Processor. Ideal For SD-WAN Deployments.
FWA-2112
Network Appliance
Intel Atom®C3000, up to 16 Cores2 x SODIMM slots with DDR4 2400 supportMultiple onboard LAN ports including 6 x RJ-45 ports and 4 x 10 Gbps SFP+ slotsSupports up to 20G QATSupport for both single and redundant PSU2 x Advantech network module expansions
-
Product
Handheld Water Quality Meters
LAQUA PD220
-
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)- 0.01 pH resolution- Offset and average slope display - Automatic / manual temperature compensation and temperature calibration function- ORP calibration option- Dissolved oxygen (DO) concentration in ppm (mg/L) and % saturation- 0.01 mg/L or 0.1% DO resolution- Compensates salinity, temperature, and atmospheric pressure - Up to 2 DO calibration points - With real-time clock and date/time stamp for GLP compliance- Auto log data; built-in memory can store up to 1000 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached- Monochrome LCD with white LED backlight: 50 x 50 mm- Phono jack output for connecting the meter to computer via PC (USB) cable for data collection and to printer via printer (RS232) cable for printout - Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrodes and calibration solutions in carrying case- 3 years meter warranty
-
Product
Digital Insulation Mult-Meter
8010 IN
-
Standard Electric Works Co., Ltd
● Microprocessor controlled.● Four insulation test voltages (DC) : 125V, 250V, 500V, 1000V● The maximum insulation measurement range is 200G ohm @1000V.● 1mA test current on insulation test at nominal voltage.● With a hand strap for easier holding.● Large LCD (78 × 67mm)● Auto-ranging.● Bar-graph indication.● Backlight function.● REL(Auto-null) function.● Auto AC/DC voltmeter.● Capacitor test.● Auto-test stop & smart hold.● Supplied with high quality test leads.● Safety standard : EN 61010-1 CAT III 600V IEC 61557-1 IEC 61557-2 EN 61326-1
-
Product
PXI Digital Multimeter, 6 digit, Enhanced Performance
M9183A
Digital Multimeter
The Keysight M9183A is a 6 digit PXI digital multimeter that measures common parameters such as DCV, DCI, ACV, ACI, 2- and 4-wire resistance, frequency, capacitance, and temperature. It offers40 ppm basic DCV measurement accuracy, excellent noise rejection, and handles inputs of up to 300 V.
-
Product
6 All-Hybrid Slot 3U PXIe Chassis; AC Powered with Up to 8GB/s System Bandwidth
PXES-2301
Chassis
The ADLINK PXES-2301 compact 6-slot PXI Express chassis, compliant with PXI Express and cPCI Express specifications, provides one system slot with three expansion slots and five hybrid peripheral slots, supporting a wide variety of enhanced-bandwidth testing and measurement applications. The hybrid-slot design accepts installation of CompactPCI, PXI, CompactPCI Express, and PXI Express modules in any peripheral slot for maximum flexibility. Built on a four-link PXI Express chassis with 8GB/s system bandwidth, the PXES-2301's peripheral slots are all connected with PCIe gen2 x4, with slot bandwidth up to 2GB/s. The PXES-2301 implements a smart system monitoring controller, reporting full chassis status including fan speed, system voltages, and internal temperature.
-
Product
Economy Mechanical Calibration Kit, DC To 6 GHz, Type-N, 50 Ohm
85032E
Mechanical Calibration Kit
The Keysight 85032E economy calibration kit contains a type-N male fixed termination and a one-piece type-N male open/short circuit. These standards are used to calibrate Keysight network analyzers for measurement of devices with 50 ohm type-N connectors. The kit is specified from dc to 6 GHz.
-
Product
PXI 8-slot BRIC Matrix, 2A, 2-Pole, 342x4, 6 Sub-cards
40-574-106
Matrix Switch Module
The 40-574-106 is a 342x4 2-pole matrix and is part of a range of BRIC matrices providing high density configurations capable of switching signals up to 2 A. The modules are available in 2, 4 or 8-slot PXI sizes and are constructed using high quality electro-mechanical relays.
-
Product
Flatness Accessory Kit
55282A
Accessory Kit
The 55282A Flatness Accessory Kit is composed of an 10759A Footspacing Kit and two 10773A Flatness Mirrors. The footspacing kit provides three precision baseplates, with 50.8 mm (2 in), 101.6 mm (4 in), and 152.4 mm (6 in) pad spacing respectively, that minimize the grid setup and data accumulation time required for plate calibration. The flatness mirrors provide 100 percent reflectance and turn the direction of an incoming laser beam 90 degrees.
-
Product
Data Diver
MT-8006B
-
LCD display for dialing number, Caller ID, Clock and other informationIndicator for determining the Line service and speedHigh impedance monitor for data safe operation without disrupting existing traffic.Smart power saving enables battery life up to 6 months12 phone number memory for speed dialing16 dialing number memoriesTone (DTMF) and pulse operationUp to 32 digits phone number memory for speed dialing keyPre-dialing and last number redial functionPBX pause key, insert a PBX pause in stored numbersTelephone line polarity indicatorsLow battery indicationBacklight functionRJ-11 port for easy test leads changeRinger and voltage LED indicationAngled bed of nails and RJ-11 plug
-
Product
Car-to-X Signal Strength Emulator
-
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS) is based on the WLAN standard IEE 802.11p from 5.850 MHz to 5.925 MHz. The connected ITS stations can be either on-board units, as they are built into cars, or road side units that are used by road infrastructure (traffic lights, road work area delimiters, velocity signs). For tests in the lab, radio modules of such ITS stations are each kept in a shielding box that prevents any unwanted radiation over the air.
-
Product
5G Router
ICR-4434W
Router
ICR-4400, GLOBAL, 5x Ethernet, 1x RS232, 1x RS485, CAN, Wi-Fi, SFP, USB, SD, Without Accessories. LTE Advanced Cat.12 Global Cellular Connectivity. Download Speed Up to 600 Mbps. Quad-core CPU with 1 GB RAM.
-
Product
NI-9220, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle
865685-01
-
NI-9220, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9220, cDAQ-9171, and cRIO-9940 includes the NI-9220 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the cRIO-9940 Backshell for strain relief and operator protection from high-voltage signals. The included NI-9220 features 16 channels and 16 simultaneous differential analog inputs with 250 Vrms CAT II or 60 VDC CAT I isolation. Additionally, you can use the NI-9220 to generate 3.2 MB/s of data at the maximum sampling rate.
-
Product
High-Speed Trimming System
LSR-3230
-
* no fixture or probe cards on top side * 2, 4, and 6 wire test capability * touch screen operation * high performance DC electrical tester * high throughput - low running cost
-
Product
16-Bit, 12 GSPS, RF DAC and Direct Digital Synthesizer
AD9164
-
The AD9164 is a high performance, 16-bit digital-to-analog converter (DAC) and direct digital synthesizer (DDS) that supports update rates to 6 GSPS. The DAC core is based on a quad-switch architecture coupled with a 2× interpolator filter that enables an effective DAC update rate of up to 12 GSPS in some modes. The high dynamic range and bandwidth makes these DACs ideally suited for the most demanding high speed radio frequency (RF) DAC applications. The DDS consists of a bank of 32, 32-bit numerically controlled oscillators (NCOs), each with its own phase accumulator. When combined with a 100 MHz serial peripheral interface (SPI) and fast hop modes, phase coherent fast frequency hopping (FFH) is enabled, with several modes to support multiple applications.
-
Product
4G Router
ICR-2834GA02
Router
ICR-2800, EMEA, 2x Ethernet, 2× RS232/RS485, USB, GPS, Metal, UK ACC LTE Cat.4 with 3G/2G fallback GNSS receiver. 1.3 GB eMMC storage to host customer SW applications 2× SIM with cover, eSIM ready.
-
Product
ATE System Power Supplies
N5700 Series
-
The Keysight N5700 Series delivers low noise power in a compact 1U package. Airflow moves front to back, so no additional space is required above or below the power supply in your automated test equipment (ATE) rack. Select output voltages from 6 to 600 V. For low current applications, the 750 W models provide 1.3 to 100 A. For higher current needs the 1500 W models provide twice as much current.
-
Product
PXI 12-Slot BRIC Matrix, 30x32 1-Pole (6 sub-cards)
40-562B-321-30X32
Matrix Switch Module
The 40-562B-321-30X32 is a high density BRIC12 matrix module with a size of 30x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
Voltage & Continuity Tester
ET250
-
The ET250 voltage and continuity tester incorporates an LCD display, measures AC/DC voltage up to 600V and can test GFCI protected circuits. Both voltage testers have a tough meter design and are rated CAT IV 600V for safety.
-
Product
High Speed Industrial GigE Cameras, 5g and 10g Models
LUCID Atlas
-
Industrial GigE (5GigE and 10GigE) cameras;IP67 models available!There are SWIR models !Ethernet Cat 6.a up to 100 m;Power supply: PoE;Resolution from 2.8 to 31.5 MP;High speed of data transfer;Price: from $ 1,250.00.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 102kΩ
50-298-040
Programmable Resistor Module
The 50-298-040 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 102kΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Strain Gauge and RTD via Ethernet
2612
-
Simultaneous measurement of four strain gauges or RTDs6 or 4-wire measurement with 200 nV resolution at a 6 Hz rateAuto-calibration cycle measures excitation at remote strain gaugeCompatible with Linux and WindowsUse our design assistant to configure a system and calculate pricing
-
Product
4G Router
BB-SR30410015
Router
SmartFlex, EMEA/LATAM/APAC, 2x Ethernet, Wi-Fi, Plastic, International Power Supply (EU, US, UK, AUS) LTE cat.4, 3G/HSPA+, GPRS/EDGE, EMEA/LATAM/APAC, 2x SIM. LTE B1, B3, B5, B7, B8, B20 VPN router, Open Linux OS.
-
Product
Test System
LB303
-
Computer Gesteuerte Systeme GmbH
The test system features the durable G12 receiver from the Virginia Panel Cooperation for the adapter interface. The LB303 is equipped with a power supply of max. 6 kW and can control up to 2 load boxes (in an external rack).
-
Product
NI-9411, ±5 V to 24 V, 6 Differential/Single-Ended Channels, 500 ns C Series Digital Module
779005-02
Digital Module
±5 V to 24 V, 6 Differential/Single-Ended Channels, 500 ns C Series Digital Module - The NI‑9411 works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and devices. The NI‑9411 is a correlated digital module, so it can perform correlated measurements, triggering, and synchronization when installed in a CompactDAQ chassis.
-
Product
RF Radio - Frequency Probes
-
*3 to 6 Ghz *PCB MCX SMB SMC *SMA U. FL MS / MM Fakra *Exchangeable inner plunger
-
Product
DataNet Wireless Data Loggers
-
The DataNet wireless system is a data acquisition solution developed for 24/7 real-time monitoring for mission critical organizations. Boasting a variety of wireless data logger models using ZigBee RF technology, the DataNet solution is capable of measuring parameters such as temperature, relative humidity, voltage, current, or frequency. Choose from DataNet models offering up to 6 inputs or the more cost-effective single or dual input Mini DataNet range, depending on your application requirements. Each DataNet mesh network is managed by a Receiver connected via USB to a Windows-based PC, and also supports addition of wireless Repeater units for extending the network transmission range and improving network robustness.
-
Product
Antennas
-
Dual polarized 6 dBi omni-directional antenna. Included with each antenna is a unique mounting bracket that allows the Ubiquiti® RocketM2 radio to be attached directly to the antenna. Also included are a pair of 195-series low-loss cable assemblies to connect the RocketM2 to the antenna. Customers can enjoy the cost saving of these kits compared to purchasing an Ubiquiti® antenna to use with the RocketM2 radio.
-
Product
ULI-417I - USB 2.0 Hub, 7 Port, Industrial, Isolated, High Retention Connectors
BB-UHR207
USB HUB
Expands one USB port to 7 USB ports (USB 2.0)ESD Level 4 (contact 8 kV, air 15 kV) Performance Criteria BData rate: 480 Mbps full speedWide operating temperature: -40 to +80 °CRugged metal case - desk, DIN rail or panel mount (brackets included)FCC, CE, UL, EMC heavy industrialHigh retention USB port connectorsUSB cable included, 1.8 m (6 ft)External power source required (not included, sold separately)
-
Product
VARIABLE TRANSFORMER DC POWER
208163V
-
Motorized Variable Transformer Controlled Power Supply, P/N 208163VInput power: 208 VAC, 6 Amps, 3 PH, 60 HzOutput: 0 to 120 VDC, 16 Amps max.Ripple: 5%Manual control with variable transformerCircuit breaker / ON OFF on the 208 VAC, 3 PH input lineProtection fuse provided on the outputPOWER ON lightIndoor enclosure: 24H x 20W x 9DVoltmeter and ammeter are installed to monitor the output.All input/output connections are available inside the enclosureSystem includes main unit and remote assembly.
