-
Product
Static Locater/Meter
90930-10001
-
Easy to use+/- 10% Accuracy20 KV at 1 inch with polarity automatically selected.Can measure higher values be increasing distance to target. Size 11 X 6 X 2.5 cm ( 4.25 X 2.5 x 1 inches)Weight 150 gm (5 oz)
-
Product
Software-Defined Radio (SDR)
Fobos
-
The Fobos SDR is a high-performance SDR receiver with a 100 kHz to 6 GHz range, 14-bit sampling, and 50 MHz bandwidth, with dual conversion and two HF channels.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, To NI PXI-2529
510150148
-
This PCB Adapter was designed specifically for the NI PXI-2529, which uses 160 signals at 2 amps. This PCB Adapter will accommodate one or two NI TB-2634 terminal blocks. If 192 signals or 3 amps are needed for a different application; use # 510 150 155 which has 6 32-pin ribbon cable connectors capable of up to 3 amps each.
-
Product
PXI 8 Slot BRIC 264x4 1-Pole (6 sub-cards)
40-562A-121-264X4
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
HD Arbitrary Waveform Generator, 2 Ch, 350 MHz, 16 bit, 128Mpts/Ch, 6 Vpp output, Wave Sequencing
T3AWG3352
-
HD Arbitrary Waveform Generator, 2 Ch, 350 MHz, 16 bit, 128Mpts/Ch, 6 Vpp output, Wave Sequencing.
-
Product
Milk Analyzers
-
Measuring parameters: FAT 0.01% - 25%SNF 3% - 15%Density 1015 1040kg/m3Proteins 2% - 7%Lactose 0.01% - 6%Water content 0% - 70%Temp. of milk 1C 40CFreezing point - -0.400 0.700CSolids 0.4 1.5%1. Sample visualization onLCD display(green)2. Possibility to measure 1 sample 90 seconds(option 60 seconds)3. Adapter 220-110 V 4.Spare silicone tubes5. Syringe6. Plastic sample holder7. Calibrations Cow, Sheep, and UHT milk8. Operation Manual9. Cardboard transport case10. CD Service PackMeasuring time 30s
-
Product
High Speed Data Logger
9330
-
The Model 9330 displays 24-bit resolution and has an impressive 3750Hz update rate. Incorporating peak and valley capture, it can store up to 6 sensor calibrations and measurements from load cells or torque transducers can be logged at 1000Hz to a standard SD card. This data can then be downloaded to a PC via the built-in USB port and Windows compatible software for off-site analysis. Adding further versatility, the rechargeable battery can power up to 4 x 350 ohm sensors, but also offers up to 300 hours stand by time and up to 20 hours continue use.
-
Product
Probes, Cables & Detectors
-
Probe has a mica window that has a thickness of 1.8 to 2.0 mg/cm2. This allows detection of alpha radiation as low as 3.0 MeV when in close proximity to the window. Beta radiation in excess of 35 keV and X-ray or gamma radiation greater than 6 keV can also be deteched. The detector is provided with a BNC connector. It can be used with most count rate and survey meters which accept Geiger Mueller (GM) detectors operating at 900V DC.
-
Product
EMC Test Equipment
TDEMI eXtreme series
-
Highest measurement speed. Highest accuracy. Incredible dynamic. New operation modes. The novel product line TDEMI eXtreme (TDEMI X) is the latest and most advanced level of full digital measurement equipment for emission testing on the fast lane. It is based on the unrivaled and patented TDEMI® real-time technology of GAUSS INSTRUMENTS. It is easy and efficient in upgrading its frequency range by a various number of extensions which can be integrated into the instrument step by step. The frequency ranges are 1 GHz, 3 GHz, 6 GHz, 18 GHz, 26.5 GHz or 40 GHz respectively. A large variety of configuration possibilities makes the TDEMI X to the customized solution perfect fitting into your lab and to your application according to civil standards (e. g. CISPR, EN, FCC Part 15, ANSI C63.2, ANSI C63.4), military standards (e. g. MIL-461G, but also its previous versions and revisions) as well as avionic standards (e. g. DO-160). The frequency range of the TDEMI X instruments starts at 9 kHz in its standard configuration and can be extended down to 10 Hz by the option MIL/DO-UG or even down to DC by the available option OSC-UG as well. Like all other TDEMI measurement systems, the TDEMI X measurement systems can be remotely controlled and fully automated via Ethernet (TCP/IP) very easily.
-
Product
Three-Phase AC Power Source 320 Vrms, 6 KVA, 5000 Hz
AC6906H
-
Keysight’s AC6900 Series three-phase power sources provide a complete AC and DC power solution by combining the capabilities of a multimeter, harmonic analyzer, and power analyzer in one instrument.
-
Product
6 ½ Digits Dual-Display Digital Multimeters
SDM3065X
-
The SIGLENT SDM3065X-SC includes a multiplexer that provides multi-point measurement capabilities. The scanner features 12 multi-purpose + 4 current channels and supports the following measurement functions: DCV, ACV, DCI, ACI, 2WR, 4WR, CAP, FREQ, DIODE, CONT and TEMP ( RTD and Thermocouple ). It provides a convenient and versatile solution for test applications that require multiple measurement points or signals and is an ideal tool for R&D burn-in and production testing.
-
Product
Power Supply 1502D
-
reliable and precise power of the output DC stabilization and digital LED displays. The output voltage is adjustable from 0 ~ 15V DC in smoothly with the knobs to control coarse and precise. Output current is regulated (limited) fluent in 0.6A ~ 2A. Securing the power supply protects it against accidental short circuits, and thus against overload and damage. In addition, the power supply has 5 fixed output voltages: 1.5 V, 3.6 V, 4.8 V, 6 V and 7.2 V, specially designed for mobile services, power systems and electronic components, etc. can be used in the design of electronic products, scientific work in laboratories, production lines and in teaching. Power can be used in the design of electronic products, scientific papers, laboratories, production lines and in teaching.
-
Product
180V-260V AC Socket Tester With RCD Test (For UK)
1943
-
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*Test for 180~260VAC circuit.*LED indicators & Digital display.*30mA leakage current measurement.*RCD Test.I*t can perform self test after plug-in ( Voltage sould be above 180V ).*Detect faulty wiring status in 3 wire receptacle.*This socket tester will give LED indication as well if the main voltage is below 200V or above 260V.*Earth loop impedance test.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 11W*Frequency: 50Hz
-
Product
Digital H.V. Insulation Tester(12kV)
7012 IN
-
Standard Electric Works Co., Ltd
● Protection class: IP66 (Lid closed)● Test insulation resistance up to 20TΩ (20000GΩ).● Short-circuit current up to 5mA● Microprocessor controlled.● 24 insulation test voltages : 500V, 1kV, 1.5kV, 2kV, 2.5kV, 3kV, 3.5kV, 4kV, 4.5kV, 5kV, 5.5kV, 6kV, 6.5kV, 7kV, 7.5kV, 8kV, 8.5kV, 9kV, 9.5kV, 10kV, 10.5kV, 11kV, 11.5kV, 12kV ● AC/DC voltmeter (600V).● PI (Polarization Index) indication.● DAR (Dielectric Absorption ratio) indication.● Auto-ranging on all insulation ranges.● Backlight function.● Menu driven.● Visual and audible warning if external voltage is present. (≥30Vac or ≥30Vdc)● Auto-hold function to freeze the reading.● Overload protection.● Adjustment for testing time (duration) : ● 1~30 minutes● Auto-off.● Calendar.● Optical USB to RS-232 data transmission.● 200 measurement results can be saved in the memory and recalled on the display.● Safety standard : EN 61010-1 CAT IV 600V EN 61010-2-030 EN 61326-1
-
Product
4-Port Serial Interface, Modular, With/Without Optical Isolation, 3.3V
CPCI-7500
-
*This Model has a 37-pin D-Sub male connector*RS232, RS422, RS485, 20 mA Current Loop*Modular structure through SI modules*With or without optical isolation*Mode configuration free for each port*128-byte FIFO-buffer, common interrupt*Transfer rate programmable up to 115,200 Baud*Option: up to 1 MBaud for RS485 and RS422*Automatic direction recognition for RS48*Mode: configurable RS232, RS422, RS485, 20 mA Current Loop (active, passive) with or without isolation (SI modules)*Transmission mode asynchronous, full, half duplex*Transfer rate: progr. up to 115.2 kBaud up to 1 MBaud on request*Protocol: 5, 6, 7 or 8-bit character 1, 1? or 2 stop bits*Parity: even, odd, none, mark or space*Interrupt lines: automatic through BIOS
-
Product
4G Router
BB-SR31000315
-
SmartFlex, Global, 2× ETH, 1× RS232, 1× RS485, Plastic, ACC Int. LTE Cat.4, 3G/HSPA+, GPRS/EDGE, Global, 2x SIM. LTE B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B28, B38, B39, B40, B41. Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
Ratemeter
TR400
-
Full-logic control process ratemeter displays speed and direction of rotating equipment.• Displays rate or time-in-process• Detects and converts 0.01 to 4,000 Hz signal input• Optional relay outputs: 2 or 6• Optional analog output: 4-20 mA or 0-10 V• Completely field programmable• Full diagnostic functions• Single-channel or bi-directional (quadrature) decoding• Front panel reverse direction indication• 3 programmable inputs• Built-in relay test function
-
Product
LXI Microwave Multiplexer, SP6T, 10-Bank, 18GHz, 50Ω, SMA
60-800-110
-
Our 60-800-110 is a 10 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PCIe 12-Bit, 6 GS/s, Gen3 Digitizer
EON Express CompuScope
-
The GaGe EON Express CompuScope PCIe Gen3 digitizer board features unprecedented speed and resolution in a 6 GS/s streaming digitizer with 1.75 GHz bandwidth and PCIe data streaming rates up to 6 GB/s.
-
Product
Power Amplifiers
-
The RF power amplifier range from Laplace is specifically designed for EMC Immunity testing according to IEC61000-4-3 and IEC61000-4-6. These are compact units with characteristics matched to the requirements of IEC standards. These RF amplifiers utilize fully isolated linear MOSFET or advanced GaAs FET devices, which provide high gain, wide dynamic range and excellent third order intercepts. High efficiency and reliable operation are achieved by employing unique RF combining circuits, RF microstrip networks, sophisticated thermal design, custom machined housing and heavy duty components. The high power RF amplifiers undergo extensive burn-in prior to final test and inspection.
-
Product
2U High Performance Rackmount Server
SKY-722V4
-
2U High Performance Rackmount Server with Intel® Xeon® 6 Processors for AI training, deep learning, and GPU-accelerated computing workloads.
-
Product
LXI 75Ω 6:1 Microwave Multiplexer 12-bank 2.5GHz 1.6/5.6
60-820-012
-
Our 60-820 Microwave Multiplexer range is suitable for switching 75 ohm signals up to 2.5GHz. With the capability of supporting up to 16 banks of 6 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted DIN1.6/5.6 style connectors. A 50 ohm version, the 60-800, is also available covering frequencies to 20GHz.
-
Product
LXI Microwave Switch, 50Ω 10xSP6T Terminated & 6xSPDT Terminated 18GHz SMA
60-890-006
-
Model 60-890-006 is a mixed configuration Microwave Switch and is suitable for switching 50Ω signals up to 18GHz. With 10 banks of terminated SP6T and 6 banks of SPDT terminated relays it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA connectors.
-
Product
PXI/PXIe RF Multiplexer, Single 6-Channel, Terminated, 8GHz, 50Ω, SMA
40-881B-001
-
The 40-881B-001 (PXI) and 42-881B-001 (PXIe) are single 6 to 1 50Ω RF multiplexers with 8GHz bandwidth and automatic termination of unused signal channels. It is available as a single or dual MUX in one and two slots respectively.
-
Product
Electrical Safety Testers
-
A high performance electrical safety analyzer that complies to a wide range of universal standards. Hipot, Insulation Resistance, Ground Bond, Leakage Current (touch current and protective conductor current) and partial discharge can all be tested. A total of 6 models are available for standard compliance tests in a wide variety of applications including R&D, quality assurance manufacturing lines and laboratory tests.
-
Product
Function Generator
FG-32
-
*6 FUNCTION,6RANGE.*LINEAR/LOG SWEEP*AUTORANGE COUNTER*0.001Hz RESOLUTION.*AUTO GATETIME.*COUNTER TRIGGER DETECT.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-Purpose Digitizer - 40 MS/s on 16 Channels, 16 Single-Ended Inputs
DN2.593-16
-
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Towing Dynamometer
RS-40K
-
RS-40K towing dynamometer is designed for testing today’s DOT Vehicles (Classes 5 and 6) which include trucks and buses. The RS-40K is built with a heavy-duty steel frame, industrial axle and rides on an air ride suspension. The RS-40K is designed to maintain 40,000 Newtons of constant drawbar force and the ability to simulate an uphill slope of 25%. The dyno uses eddy current absorbers with special high temperature coils. The power is provided by an industrial generator. Testing is unlimited at lowspeeds.
-
Product
Power Quality Analyzer
APQM-700
-
*4 current inputs, physical current measurement on the neutral conductor.*Recording of up to 1100 parameters, including average, maximum, minimum and instantaneous values*Built-in heater, stable operation at low temperatures down to -20ºC.*Internal rechargeable battery, meter autonomy (min. 6 hours)*Ingress protection IP65, possibility of working in rain, snow and high humidity.
-
Product
Light Source
-
OrienTek Optical Technology Ltd.
High Precision● Highly accurate unit offering 6 calibrated wavelengths● Interchangeable connectors● Durable and reliable design● Easy-to-use interface forerror-free testing● Rubber armor protection
