Magnet
Attract iron and are surrounded by a magnetic field.
-
Product
3-AXIS DIGITAL ELF GAUSSMETER: 20-4000 Hz
IDR-210
-
Integrity Design and Reseach Corp.
Typical Applications include checking the frequencies and magnetic fields (BW: 20-4000 Hz) produced by equipments such as computer monitors, television sets, power lines, induction heaters, industrial, scientific and medical equipment and household appliances, etc. Magnetic fields are invisible radiations, the best method to detect them is by using one of the accurate gaussmeter from Integrity Design & Research Corp.
-
Product
Materials Measurement Suite
N1500A
-
With Keysight N1500A materials measurement software suite, you can determine the intrinsic electromagnetic properties of many dielectric and magnetic materials. The complete system is based on a versatile Keysight network analyzer which measures the material’s response to RF or microwave energy. The N1500A software controls the network analyzer and calculates results. Depending on the Keysight network analyzer and sample holder or fixture used, frequencies can extend from a few hundred MHz into the low THz.
-
Product
Radiating Loops
-
The magnetic, handheld coil was designed to generate defined mag-netic fieldstrength in the frequency range from DC up to 5 (7) MHz. The main application is immunity testing against magnetic fields.
-
Product
Shaft Speed Switches
-
A speed switch senses rotating shaft speed, comparing it to one or more settable over/under/zero speed alarm trip-points. A shaft speed sensor detects magnets embedded in a shaft-mounted pulser wrap/disc. As the shaft rotates, the passing magnets are detected across an air-gap as pulses with frequency proportional to shaft RPM. When a conveyor belt or bucket elevator begins to slip the pulse frequency (shaft RPM) crosses to the alarm side of a trip-point threshold, a corresponding relay de-energizes, providing shutdown or alarm.
-
Product
Opto-Isolated Current Loop Signal
4029
-
SPECTEC Innovative Sensor Solutions
SPECTEC's Model 4029 digital opto-isolated current loop signal conditioner prevents ground loops and interrupts any galvanic signals riding on magnetic speed sensor's output signal.. This signal conditioner converts magnetic, variable reluctance and inductive sensors' sinusoidal signals into a 4-20 mA output suitable for interfacing with process control units, dataloggers, flow controllers, and computers.
-
Product
Magnetic Field Sensors
-
Analog Devices magnetic field sensors combine integrated bulk Hall cell technology and instrumentation circuitry to minimize temperature related drifts associated with silicon Hall cell characteristics. The architecture maximizes the advantages of a monolithic implementation while allowing sufficient versatility to meet varied application requirements with a minimum number of components.
-
Product
Digital Arrester Clamp Tester (with Data output)
ALCL-40H
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*ALCL-40 is designed to test the diagnostic of OXIDE SURGE ARRESTER.*The least influence from the external magnetic field and noise by triple shielding of CT.*Compliant with IEC6099-5.*Enabled the measurements for 100nA resolution and harmonics current.
-
Product
IC Side Channel Analysis
-
These probes allow you to couple fast, transient magnetic field, E-field, and current pulses into ICs.
-
Product
Vehicle Electromagnetic Field Exposure Test System
SEM-400
-
Beijing KeHuan Century EMC Technology Co,.LTD
Vehicles are our daily public transportation. Electromagnetic pollution in vehicles has attracted more and more public attention. The newly revised compulsory standard GB27630-201X "Passenger Car Air Quality Evaluation Standard" intends to require the electromagnetic field in the car as one of the indicators, according to GB/T37130-2018 "Measurement method of vehicle electromagnetic field relative to human exposure" The measurement method is to measure the intensity of the magnetic field in the car. In the frequency range of 10Hz-400kHz, the electromagnetic field measurement result should meet the public limit requirements of GB8702-2014 for electromagnetic exposure.
-
Product
Vision Measurement
CMM Camera System
-
Aberlink’s camera system offers a non-contact facility on any Aberlink CMM. A innovative design of magnetic, kinematic joint allows the probe and camera to be swapped in just seconds. This means that components can be inspected using both touch trigger and vision inspection technology on the same machine.
-
Product
DC Power Supplies
LPS Series
-
The LPS series power supplies are designed for various applications in semiconductor equipment along with OEM and industrial applications. Available for use in constant current or constant voltage applications they are available in power levels from 1,000 to 13,500 Watts. Common applications include heater, filament and magnet supplies along with test and burn-in applications. All models can be paralleled for increased power and custom configurations are available.
-
Product
AC Magnetostriction Measurement Equipment
TLVM
-
This equipment measures quantitatively magnetostriction to indicate mechanical striction in magnetizing direction caused when magnetic steel sheet sample was alternately magnetized and is used for research and development of magnetic steel sheet. Magnetostriction is detected as speed signal through the parameters of magnetic flux density and compressive stress with laser doppler vibration meter.
-
Product
Magnetic Sensors
-
BERNSTEIN offers electromechanical reed contact magnetic switches and electronic versions which operate according to the Hall and magnetoresistive principle.The electronic versions are characterised by their enhanced mechanical properties (extremely high resistance to vibration, shock or impact) and are not prone to wear in operation. Thanks to the use of only one single “active” component (reed contact), “traditional” electromechanical magnetic switches are extremely reliable in operation. The universal current capability and low procurement costs allow these switches to be used in a wide range of applications.
-
Product
Magnetic Research System
MagRS
-
The MagRS base system comes with a 4 or 7 in magnet, with additional options to customize the system for your experimental needs. Choose to add VSM capability, temperature option accessories, or optical access. MagRS comes standard with ExactGAP magnet pole gap indexing and GlideLOCK precision sample positioning.
-
Product
Hall Probes
-
Hirst Magnetic Instruments Ltd
is a magnetic field sensor that passes electrical current when the sensor is perpendicular to a magnetic field. The stronger the B-Field, the more current it passes. Pira DCS # 5M10.10.
-
Product
TMR Angle Sensors
-
MultiDimension Technology Co.,Ltd.
Angle sensor are proportional to the sine and cosine of the angle of a magnetic field applied parallel to the surface of the sensor, which can be provided by a small magnet positioned above the device.
-
Product
Door Contact Sensor
ENVIROMUX-M-DCS
-
Monitors access with a magnetic bridge sensor, which responds to any magnetic material (no special inserts necessary). Can also be used for monitoring side wall and covers. Includes mounting hardware. For normally closed circuit connection. 2-wire interface. Screw terminal. Maximum cable length: 1,000 ft. Wide actuating gap, approximately 1". Dimensions WxDxH (in): 0.5x0.5x2 (Switch), 0.5x0.5x2 (Magnet). Operating temperature: 32 to 158°F (0 to 70°C). Regulatory approvals: RoHS.
-
Product
Calibration & Demag.
Model 5655
-
The model 5655 is a capacitive-discharge magnetizer / demagnetizer / calibration unit.
-
Product
Magnetic Field Tester
MS-440
-
This device recognises fast and simply magnetic fields generated by electric reels and permanent magnets.
-
Product
Three-Phase Transformer Winding Resistance Meters
TWA Standard Series
-
When it comes to winding resistance measurement on three-phase power transformers and autotransformers, TWA Standard series offers some of the most technically advanced instruments with LCD display in the market. Both models are capable of testing six transformer windings with a one-time cable connection, as well as three-phase automatic transformer demagnetization. The stored magnetic energy is safely automatically discharged at the end of the test. The built-in tap changer control unit enables automated test mode, where the instrument operates the tap changer without operator input and records winding resistance results based on pre-selected stabilization criteria. This option makes the operator’s job significantly easier.Both models can output test currents from 5 mA to 25 A DC for the purpose of winding resistance measurement. TWA40D has a special test mode for checking the synchronization of on-load tap changers with three phases simultaneously tested in parallel, in which the total test current can rise to up to 40 A DC.TWA40D has additional advantages when it comes to non-intrusive tap changer analysis. The unique DVtest method enables checking the moving contacts of on-load tap changers during the transition, measuring the transition time, detecting open circuits, and many other types of faults. It is performed with 0.1 ms sampling rate, simultaneously with the measurement of tap changer motor current which helps with the detection of motor and mechanical issues. A special proprietary algorithm is used for testing tap changers connected through a built-in series (booster) transformer. The DVtest can be performed either on one phase or on three phases simultaneously. It can also be performed as an additional test simultaneously with the winding resistance test in all tap positions.An additional unique advantage of TWA40D is the capability of simultaneously testing the winding resistance of all three phases of a three-phase transformer (connected in a YN configuration). This can significantly shorten the total testing time – for example, it enables the operator to perform 33 measurements instead of 99 on a tap changer with 33 tap positions.The test leads for TWA three-phase transformer winding ohmmeters are interchangeable with the TRT turns ratio testers, which means that both sets of tests can be performed with a single test lead connection to the power transformer terminals.
-
Product
Digital Power Transducer
LP Series
-
*High accuracy 0.07% rd + 0.03% ro*Excellent long term stability*Outstanding over capability and temperature performance*Wide selection of input / output ranges*Meets ANSI C37.90 (1989) and BEAMA No. 219 tests*High magnetic field immunity*Real power - able to measure distorted waveform
-
Product
Highly Inductive Resistance Meter
MR 8050
-
With the MR 8050 resistances highly inductive Resistance Meters windings of transformers, motors and reactors can be measured. (range 100 µΩ with 0.01µΩ resolution up to 6 kΩ). The performance of the test objects can be up to 800 MVA or even more. The magnetic loading of a transformer is performed quickly using a high loading voltage (60V). This is important for time critical measurements (cooling curves). The unloading of the transformers core is very fast, very safe, as the energy is total destroyed in the MR 8050.
-
Product
For Detecting Low Range And Leakage AC/DC/Pulsed Current.
FDAZCT-20L-0.6S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Lowest Influence from Magnetization,Temperature *Change,Residual Current and Terrestrial Magnetism.*Low Cost and High Performance (Output Linearity ±1% F.S)
-
Product
Proximity Sensors
-
Premier Electrosystems is an esteemed name in the manufacturing of inductive proximity switch, photo sensors, capacitive sensors, magnetic sensors, hall effect sensors, analog sensors, encoders, infrared sensors, etc. with NABL calibration certificate
-
Product
Nuclear Magnetic Resonance Equipment
SpecFIT HRC27
-
Low-field Nuclear Magnetic Resonance (NMR-DT) equipment with user-friendly interface software and data analysis under development. Compatible with Industry 4.0
-
Product
Handheld Gaussmeter
HGM09
-
Data storage on a personal computer via keystroke. The HGM09s is easy to use and has a good price/performance ratio. The handheld gaussmeter HGM09s is used to measure magnetic DC and AC fields. The measurands are flux density in Tesla or Gauss and the field strength in Amps per meter.
-
Product
Replacement Selenium Surge Suppressor Specialists
-
Surge suppressors are used to protecting circuits from transients (sudden, brief increases in voltage). Transients of widely varying magnitudes are caused by such circuit components as motors, coils, magnets, relays, and transformers. They are found in all electrical systems and are notorious for damaging diodes, SCRs, transformers, triacs, and relay contacts.
-
Product
Vibrating Sample Magnetometer
-
Is a scientific instrument that measures magnetic properties based on Faraday’s Law of Induction. High speed measurement adopting high temperature superconductivity and high accuracy measurement of small sample of Br,HcJ become possible.
-
Product
Coating Thickness Meter for Ferrous and Non-Ferrous Substrates
CM8822
-
- Operating principle: magnetic induction/eddy current (F/NF)- Measuring range:0-1000um- Resolution; 0.1/1- Accuracy: 卤1-3%n or 卤2.5um- Min. measuring area: 6mm- Min. sample thickness: 0.3mm - Battery indicator: low battery indicator- Metric/ imperial: convertible- Power supply: 4x1.5V AA(UM-3)battery- Auto power off- Operating conditions:0-+45鈩?/span>(32鈩?/span>-104鈩?/span>),鈮?0%RH- Dimensions: 160x68x32mm- weight: 250g(not including battery)- Optional accessories: other range 0-200um to 15000um
-
Product
Single Axis Magnetometers
MAG Serie
-
Macintyre Electronic Design Associa
The µMAG series is the premiere, handheld instrument for the precision measurement of the vector components of weak static and low frequency magnetic fields. The superior stability, linearity and accuracy of the uMAG, compared to Hall Effect or Magnetoresistance base instruments, make it the only choice for high quality low magnetic field measurements and best choice for gerneral purpose magnetometer applications.
