Combinational Testers
ICT, Functional test, and boundary scan test all in one piece ATE.
See Also: In-Circuit Test
-
Product
Environmental Testers
-
Our range of environmental test equipment provide users to test and measure all aspects of the environment. The comprehensive range includes temperature, infra red, sound level, humidity, LUX level and air flow.
-
Product
Network & Cable Testers
-
Detects PoE end/mid-span voltages on network cables. LED indicators instantly show “GO/NO-GO” detection on PoE networks. Plug cables directly into the builtin RJ45 jack or use the included patch card to detect voltage in wall jacks.
-
Product
Burn-in Board Continuity Tester
CT-1
-
Burn-in Board Coninuity Tester. Verifies burn-in board continuity and component tolerances. 768 I/O channels, can be forced to the constant current source or grounded independently. Highly accurate measurement of resistance, voltage, and capacitance using a pair of precision instrumentation amplifiers.
-
Product
Loudspeaker Cable Testers
EMO E450
-
The EMO E450 cable tester will test for continuity, cross connection, and open circuit in cables fitted with NL8FC 8-pole and NL4FC 4-pole Speakon connectors, 3-pin XLR connectors, and 2 or 3 pole A-gauge jacks. EP retrofit kits are available to allow cables fitted with EP 4, 5, 6, or 8 pin connectors to be tested. The EP connectors fit in two pre-punched holes on the rear of the tester accessed by removing the blanking panel. The kit's flying leads plug directly into connectors mounted on the tester's PCB.
-
Product
Multifunction Earth Tester
MT-200
-
Multifunction earth tester for measuring earth resistance, protective conductors’ continuity, insulation up to 1000V, with touch-screen display and integrated Wi-Fi
-
Product
Memory Tester
RAMCHECK LX DDR3
-
Quickly test DDR3 DIMM and SO-DIMM memory. In just seconds, RAMCHECK LX will perform a thorough test of the module and provide complete identification. Also tests expensive LRDIMM modules.
-
Product
CT Burden Tester
585
-
The 585 Burden Tester is a hand held unit rated for use up to 20A. The design features a digital LED meter for displaying the current transformer (CT) secondary current. The burden is applied for a specific length of time controlled by circuitry inside the unit to help prevent the burnout of the burden elements.
-
Product
HDMI Tester
21-8575-00
-
The HDMI Tester is designed to provide fast convenient verification of proper pin connections of HDMI cables and wall plates. The set includes a Main Test Unit and Remote Test Receiver.
-
Product
Pitot-Static Tester
PS-525
-
The PS-525 Pitot-Static tester is a low-maintenance digital tester that is fully portable.
-
Product
Transformer Winding Resistance Testers / TRT ? 2
TRT-2
-
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Fast measurement: Test current 0.02A to 2A DC, Digital display of resistance and test current.
-
Product
IEC60669 Pendulum Impact Tester
CX-BC2
-
Shenzhen Chuangxin Instruments Co., Ltd.
This Pendulum Impact Test Device Conforms to the standard GB2099.1, GB16915.1 and IEC60669, IEC60670 standard. To check the impact resistance performance of plug and socket electrical accessory's enclosure.
-
Product
Digital (1kV below) Insulation Tester
2801 IN
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled with advanced safety features.● Three test voltages : 250 / 500 / 1000V.● Displays and sound warning if external voltage present.● Ener-Save™ feature to extend battery life.● Continuous battery monitoring.● Auto ranging / auto-null / auto-off.● Insulation tested at 1mA.● Built-in carry case, test leads in separate pouch.● Real-time barg-raph display of test voltage and voltage decay during discharge.● Audible and visual message displayed if external voltage is present.● Large LCD.● Display can be customized for special orders.● Continuity buzzer.● Show test time duration (up to 99.9s) for easy comparison.● BS 16 edition.
-
Product
Installation Tester
MT-300
-
Advanced multifunction installation tester for verification of electric safety of private and industrial electric systems
-
Product
Friction and Wear Tester
EFM-III Series
-
The EFM-III series is a friction and wear tester for tribology evaluation in conformity with JIS K 7218. This tester is designed for scientific elucidation and technical evaluation of the characteristics relating to sliding friction, wear and lubrication, that are surface behaviors of relative properties of two interacting material surfaces (relative properties of solid materials in relative motion).
-
Product
Digital ELCB (RCD) Tester
2712 EL
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 2 Lines × 16 characters LCD.● Very low consumption.● 50Hz and 60Hz operation.● Menu-driven.● Accurate digital readout of disconnection time.● Automatic data hold function.● Over temperature protection.● Over voltage protection.● Fuse protection.● Zero crossing circuitry permit testing at 0° or 180°.● Disconnection phase polarity shown on LCD display.● Auto off and off override.● Polarity trip indicator (positive or negative phase)● Wiring polarity indicator.● Measure voltage between Line and Earth before testing.● Frequency measurement indication.
-
Product
Battery Internal Resistance Tester
TOB-R-203
-
Xiamen Tob New Energy Technology Co., Ltd
Battery internal resistance tester used for lithium battery, lead-acid battery, Ni-Cd/Ni-MH battery and all kinds of batteries.
-
Product
Automated Filter Tester
3140-1
-
The model 3140 filter tester uses the same aerosol generation technology as the model 8130A respiratory filter tester. It works with Emery oil, DOP, DEHS, paraffin and other oils. Two new generation CPCs simultaneously count upstream and downstream particles. This enables accurate, repeatable and fast measurements, for example a HEPA filter can be tested in less than 15 seconds.
-
Product
Cable Testers
TEST-9110 Series
-
Designed to measure and control the DC resistance, electrical capacity, insulation resistance of electrical circuits and check the electrical insulation strength of electrical circuits.
-
Product
Gurley Legality Tester
DRK461A
-
Shandong Drick Instruments Co., Ltd.
It can be applied to quality control and research and development of papermaking, textile, non-woven fabric, plastic film, etc
-
-
Product
IoT Tester for Cellular & Non-Cellular Technologies
CMW290
-
The R&S®CMW290 is the ideal test solution for the integrated wireless communications modules used in laptops, data cards, wearables and various IoT products. The R&S®CMW290 offers functions tailored to these applications within the R&S®CMW product family. The tester provides network emulation (signaling mode) as well as generator and analyzer functions for the supported cellular and non-cellular standards including GNSS and broadcast technologies.
-
Product
Gigabit Ethernet Tester
GET-100
-
GET-100 is a handheld 10M/100M/1000M gigabit Ethernet tester, used for the Ethernet installation, operation and maintenance services.The GET - 100 design in a small and portable device which provides packet capture, network monitoring, networkperformance testing, data generation, test leads and error test functions in an organic whole unit. It is widely used in network layer 1/2/3 BER test and RFC - 2544 test. GET-100 help maintenance people to quickly locate fault and analysis network
-
Product
Protection Relay Tester
PW866i
-
PW866i (6×32A, 4×300V) Protection Relay Tester could be used for testing all kinds of relays, also supports testing IEC 61850 combined relays. Its local control system is with 10.4inch LCD screen based on Windows system.
-
Product
5 kV INSULATION TESTER
MD-5075x
-
The digital megohmmeter model MD-5075x is Megabras' cutting edge insulation analyzer equipment and it is one of the most complete and sophisticated available in the international market. A powerful software allows for further analysis of tests results, including features such as graphical representation and automatic report generation.
-
Product
Mini Lan Tester
21-8580N-0
-
Auto decipher the link status is NIC or Hub.?The deveices is working in 100 Base -TX Full Duplex 10 Base-T Full Duplex or Half Duplex?The deveiceis transmitting a pack or not?Data transmitting error has occurred
-
Product
Portable Electricity Meter Testers
EE-120A-3S
-
The EE-120A-3S unit consists of a three-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types of electricity meters using the voltages of the network. The meter error can be measured for active, reactive or apparent energy in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Maximum Demand Test, Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the three-phase network – with direct measurement or with optional current clamps.
-
Product
Insulation Resistance Testers
-
Shanghai Beha Electronics Co., Ltd.
*This is a variable high voltage insulation tester from 500V to 15kV in 500V steps.*The is menu driven and uses Dynamic Current Auto ranging technology.*It has a Bar-Graph which displays the voltage stressing the insulation while the test is in progress and the voltage decay during the automatic discharge of the tested circuit.*The top line of the display shows the elapsed time at the start of the test. Digital readout of the total time will remain displayed even after testing has ceased.*A 4-digit display (2000 counts) is showing the actual insulation resistance.*This instrument displays a voltage warning and sounds when AC or DC is present before injecting the test voltage.
-
Product
Combustion Leak Tester
AC560000
-
Fast, economical and accurate method to test for combustion gas leaks in head gaskets, cylinder heads and engine blocks. Dual chamber design provides more accurate test results. Test fluid can be used for both gasoline and diesel engines.
-
Product
Portable Hydraulic Testers
-
Flo-tech portable hydraulic testers simultaneously measure the flow rate, temperature and pressure of hydraulic fluid. Flow rates are derived from an internal turbine meter assembly. These units were designed for testing pumps, valves, cylinders, motors, hydrostatic or power shift transmissions and power steering systems in both mobile and stationary applications. When used in a preventive maintenance program, untimely or catastrophic repairs are minimized. Three families of testers are available to provide operators with the perfect solution that fits their needs, each quipped with a carrying handle to improve portability.
-
Product
Battery Testers
-
Wuxi IMHOO Technology Co., Ltd.
Voltage of batteryBattery type1.5VButton Cell, AA,AAA,C,D,N3V Lithium6V Camera Battery9V 12V 15V 22.5V Power Source Not use batteryWeight 260gmeasurement 100x63x33mmPacking50pcs/CTN
