RTU
Collects data from data acquisition (DAQ) devices and transmits the information to the main test system via a network.
-
Product
Load Cell Transmitter
MODEL SST-HV
-
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Low Power Wireless Gas Detector
CX
-
Teledyne Gas & Flame Detection
Model CX sensors are equipped with standard analog 4-20mA, and Modbus™ RTU RS-485 outputs and can be used with SmartWireless Site Sentinel CX/CXT controllers. The CX is a very low power device making it an ideal choice for a battery powered detector (optional) in applications where power is unavailable or not economically feasible.CX gas detection sensors are easily and economically deployable in both permanent and temporary installations. These low power sensor assemblies utilize electrochemical technology for a long list of toxic gases.
-
Product
High-power DC Electronic Load (6kW~60kW)
FT68200A/AL/E Series
-
Shenzhen FaithTech Technology Co., Ltd.
FT68200 series high performance high-power DC electronic load provides three voltage ranges 150 V/600 V/1200 V, maximum current 2400 A per single unit, stand-alone power from 4 kW to 60 kW, expandable up to 600 kW, 10000A by master-slave paralleling. Ultra-high power density, 6kW is with only 4U height. Wider operating region, faster dynamic frequency, as well as transient mode, OCP/OPP test, sequence test, automatic test and battery discharge test functions greatly enhances its test strength and expands application coverage. Furthermore, two times instantaneous overpower loading capability can effectively reduces user’s test cost. Built-in standard RS232, RS485, LAN, USB (serial), optional GPIB and CAN interface, supports SCPI, ModBus RTU and CANopen protocol, which facilitates system integrators. FT68200 series has full protection functions, which can be applied to power battery discharge, DC charging station, charging piles, charging pile modules, vehicle On Board chargers (OBC), high-power switching power supplies, power electronics and other power electronics products.
-
Product
4 Digit Process Meter
CM2-PR
-
CM2-PR Process Meter has been designed in simple operation and 4 digital 20mm LED display with economic cost.They are can be programmed by buttons that are hidden in front panel.They are also available to option 2 relay output and an analog output or RS485(Modbus RTU Mode) communication.
-
Product
4 2/3 Digital Process Meter (1/32 DIN)
CS3-PR
-
CS3-PR Process Indicator has been designed with 0~10V and 4(0)~20mA high accuracy measurement.A compact body design for small equipment, laboratory instrument, and others.Also are available with relay output, analog output, RS485 Modbus RTU communication to cover a wide range of applications.
-
Product
5 Digit Preset Counter
CS2-CT
-
The CS2-CT provides high speed and multifunction, counting, control and communication (Modbus RTU mode) of Pulse from flow meter or encoder, proximity switch, photo switch for length control.There are 3 external control input (DI) in standard and the optional 4 Relay, 1 Analogue,and RS485 port available. They are also support N, R, C mode for totalizer control.
-
Product
12DO(Source Type) Modbus RS-485 Remote I/O
ADAM-4056SO
Remote Interface Unit
12ch source type digital outputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system5000VDC isolation protection
-
Product
5 Digit Tacho/Linear Speed Meter (1/32 DIN)
CS3-RL
-
CS3-RL indicator was designed with high accuracy measurement of pulse and frequency.The innovation feature is input from 0.01Hz~100KHz the display resolution will auto-range according input frequency to shift decimal point.A compact body design for small equipment, laboratory instrument, and others.Also are available option relay output, analog output, RS485 Modbus RTU communication for most popular applications.
-
Product
Multifunctional Meter
CPM-10
-
CPM-10 Multifunction Power meter measure single phase 2 wire ,single phase 3 wire, three phase 3 Wire and 3 Phase 4 wire systems with high accuracy measurement for parameters such as voltage, current ,active power, reactive power, apparent power, power factor ,frequency, effective energy (V,A,W,Watt-Hr,Var,Var-Hr,VA,PF,Hz), having LED display and standard communication RTU Modbus RS485..Optional functions 1 set relay output,1 analogue,1 RS485 (ModbusRTU Mode) or 1 pulse output. Most suitable for power management,remote input /output, alarm and remote signal control uses needs.Case depth 120mm only, easy panel mounting installation
-
Product
5 Digit Programmable Speed/Velocity Meter
CM1-RL
-
CM1-RL series provides a simple economic programmable speed/velocity table, it 20.0mm, 5-digit LED display, press the key to set the display range and its anti-jamming design and reliable quality, simple installation, you can meet the needs of general measurement of speed/velocity.This instrument also has 2 group relay outputs, 1 analog output, or 1 groups RS485 (Modbus RTU mode) communication features three a (More features please refer to page description). Operation press the inner design, the more human-no action can be avoided, especially suitable for all kinds of machinery used.
-
Product
ANSI X3.28 to Modbus RTU Converter
Model 2399
-
* Converts ANSI X3.28 commandslinto Modbus RTU packets.* New 32 Address Mode supports multi-channel Modbus Controllers like the Watlow MLS300.* Control Modbus RTU devices from any ASCII serial source.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes serial baud rate conversion.* Internal logic is IEEE-488.2 compatible and uses SCPI commands for configurtion setup.* 2399 mounts on a DIN rail or on any flat panel.* Inexpensive way to maintain manufacturing equipment such as semiconductor fusion chambers, etc as the ANSI Controllers become obsolete.* Application Note AB23-3 describes how to use the 2399 to replace obsolete Watlow Controllers in the Axcelis/Fusion Gemini Asher.* 2399 Serial Keyboard Program lets you control and setup the 2399 and test the ANSI modes.* 239x Table Loader Program uploads ANSI Command Table entries from an Excel csv file.
-
Product
Multifunction Meters
-
Measures V, A, PF, Hz, KW, KVA, KVAr, Kwh, KVAh & KVArhTRMS MeasurementCan be used for Continuous MonitoringAuto / Manual Scroll Display (User Selectable)State of Art Microcontroller DesignPortable, Handy, Plug-n-Play and Easy-to-useLCD Display with BacklightRS-485 5KV Isolated Port (Optional) with MODBUS RTU Protocol (Optional)POWER MASTER Software for MIS Reports (Optional)
-
Product
Load Cell Transmitter
MODEL SST-LV
-
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Thermocouple Temperature Indicator
CM2-TC
-
CM2-TC Thermocouple Temperature Indicator has been designed in simple operation and 4 digital 20mm LED display with economic cost.They are can be programmed by buttons that are hidden in front panel.They are also available to option relay output and an analog output or RS485(Modbus RTU Mode) communication.
-
Product
RH and Temperature Digital Transmitters
HD9817T… Series
-
Dual relative humidity and temperature transmitter for HVAC applications, environmental monitoring, pharmaceutical storage, food transport, greenhouse automation, etc. Equipped with an IP65 stainless steel AISI 304 housing, it is suitable even for severe environments; besides, its ultra-compact dimensions (Ø 14 x 133 mm) and wide range of outputs (analogue 0…1V, digital RS232C OR RS485-MODBUS RTU, USB 1.1-2.0) make it ideal for integrating into a variety of OEM applications. It is supplied with the HD9817TC software for reading measurements and calibrating the relative humidity sensor.
-
Product
RTU (Remote Terminal Unit)
R2+ RTU
-
*The R2+ Remote Terminal Unit (RTU) is a distributed architecture and large I / O capacity designed to meet the various demands of current Power SCADA / EMS applications.
-
Product
Autonomous RTUs
-
Infinite Industrial Informatics Lt
Autonomous RTUs are power network independent devices, opening up new horizons for telemetry in off-grid areas. An autonomous RTU features in measuring capabilities and contains a wireless MODEM for data and alarm transmission. It can also provide all necessary circuits for powering measuring transducers and sensors. The device is commonly powered by an internal battery and is housed in a IP66 to IP68 enclosure for outdoor use. The battery lifetime requirements extend from few months to 15 years. Another common requirement is continuous, maintenance free operation in harsh environmental conditions and extended temperature ranges.
-
Product
Modbus Register Converter
Model 2390
-
* Converts Modbus Registers and variables for replacement Modbus devices.* Maintain existing software when upgrading Modbus systems.* Provides serial control of Modbus RTU devices from any ASCII source.* User defined Register Conversion Table supports all Modbus RTU devices.* Internal Register Conversion Tables for Watlow F4-to-EZ-ZONE and F4-to-F4T conversion.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes baud rate conversion capability.* Uses SCPI commands to load the Conversion Table and set serial settings.* Small metal case mounts on a DIN rail or on any flat panel.* 239x Table Loader Program uploads the 2390 Register Conversion Table from an Excel csv file.* 239x Serial Keyboard Program provides instant control of the 2390 and Modbus Slave Devices without writing a program.
-
Product
16DI Modbus RS-485 Remote I/O
ADAM-4051
Remote Interface Unit
16ch digital inputProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system2500VDC isolation protection
-
Product
10 Digit Rate/Batch Counter
CS2-MC
-
The CS2-MC provides dual input(A/B phase) and display with high speed, counting, control and communication (Modbus RTU mode) of Pulse from encoder, proximity switch, photo switch or flow meter for counting, length and position control. There are 3 external control input (DI) in standard and the optional 4 Relay, 1 Analogue, and RS485 port available.The relays are also support N, C, R, E mode and Hi/Lo energized for batch / totalizer and position control.
-
Product
Economic Type Potentiometer Indicator
CS1-PM
-
CS1-PM economic type Potentiometer Indicator has been designed with high accuracy measurement, display and communication of resistance (3 wires) as like as Positioner.The meter supports Field Calibration function. It can be calibrated with sensor (Potentiometer) to meet machinery structure.They are also available 1 option of 1 Relay outputs, 1 Analogue output or 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
Product
Modbus Controllers
-
Datexel has a range of Modbus RTU Masters, Slaves, Controllers, Data Loggers and Modbus remote displays. The DAT9000 is a Modbus RTU Master with RS485, RS232 and Ethernet Interfaces. The DAT9000IO is similar to the DAT9000 but it has digital input and outputs. The DAT9000DL has an additional Data Logging facility and the DAT9000DLIO has both Data Logging and digital IO. The DAT9011 is a Modbus Master with 2 analog inputs which can chose from Thermocouple's, RTD's, Potentiometers, mA and mV's. It also has 2 outputs which can be mA or voltage. The DAT9011 can also accept digital inputs and provide 2 SPDT relay outputs. The DAT9011DL also has a Data Logging facility which can store up to 8gb of readings on a thumb drive.
-
Product
Digital Panel Meter
MPF-5A
-
Mx-5A meter to provide power (Watt or Active Power or Re-active Power or Power Factor), high-precision measurement, display and remote communication capabilities.Additional purchase: 1 group of relay outputs, 1 analog output, an RS485 communication output (the Modbus RTU Mode) interface, so that can be installed in power management, remote input and output, alarm and variety of remote communication control the use of needs.120mm (D) is ideal for assembling in panels with limited penetration depth
-
Product
Microprocessor Multifunction TRMS Power Meter + Harmonics Analyzer
8100 C
-
Kusam Electrical Industries Limited
INPUT :• Input Voltage Range :Voltage: 55 ~ 300V AC, or 300 ~ 600V AC, 45 ~ 65Hz.P.T. Ratio Programmable upto 9999 / KV.• Input Voltage Over Range :Voltage : 200 % Continuous, 300 % of rating for 10 sec.• Input Current Range :Current : 110 % of rating. 0-1A or 0 - 5AC.T. Ratio programmable upto 9999 / 5A.Input Current Over Range:Current : 400 % Continuous, 2000 % of rating for 10 Sec.• Input Frequency : 45 Hz ~ 70 Hz.• Input Burden :Voltage 0.25 VA / Unit, Current 0.25VA / Unit, at 50 / 60HzOUTPUTDC Current: 0 20 m A DCLoad resistance drive: output drive 10 V DC maximum.DC Voltage: 0 -10 V DCLoad resistance drive: output drive 5mA maximumOutput Protection: No damage even if output is Open or Short Circuit.Output Response Time : £ 1 Sec.Digital Output : RS485 Output, Isolate Type with MODBUS RTU mode., 4800, 9600,19200Baud Rate, User Selectable.
-
Product
Modbus RTU Rs486/232/422
-
It provides client/server communication between devices connected to different types of buses or networks. Modbus-RTU (Remote Terminal Unit) means that the Modbus protocol is used on top of a serial line with an RS-232, RS-485 or similar physical interface.
-
Product
Voltage/Current Indicator
CS3-VA
-
CS3-VA Voltage/Current Indicator has been designed in miniature size(24 x 48mm), and provide high accuracy measurement, display and communication of 0~300V or 0~20mA for DC/AC(average).They are also to build 2 Relay outputs, 1 External Control Input, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication.
-
Product
4 2/3 Strain Gage Meter (1/32 DIN)
CS3-SG
-
CS3-SG Strain Gauge Indicator has been designed with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV as like as Load Cell or Strain Gauge.The meter supports Field Calibration function. It can be calibrated with sensor(Load Cell/Strain Gauge) to meet machinery structure.They are also building in 2 Relay outputs, 1 External Control Input, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
Product
1-Port Modbus Gateway
ADAM-4572
IoT Gateway Platform
Supports Modbus/ASCII, RTU Protocol to control devices. Allows up to 8 clients to access field data simultaneously. Up to 31 Independent serial ports if configured to RS-485 serial mode.
-
Product
Remote Test Unit (RTU) Expert
RTU Series
-
VeEX’s Remote Test Units (RTU) are self-contained, scalable test and monitoring probes for communications networks. When used as part of the VeSion cloud-based monitoring system, these rackmount probes are optimized to work with a centralized server system. In addition, the probes can be operated in standalone mode via web browser.
-
Product
Wiring Boxes
-
Radio receiver for heating / cooling systems equipped with an integrated antenna, an output with SPDT relay and an RS485 Modbus® RTU slave communication port.
