Impulse Winding Testers
See Also: Coil, Insulation Test, Surge Testers
-
Product
Earth Resistance Testers
-
Precision Mastech Enterprises Co.
Specialized instruments used to measure the effectiveness of grounding systems in electrical installations.
-
Product
AMIDA VCSEL Tester
-
AMIDA VCSEL tester can be divided into three parts: LIV measurement system, Near Field measurement system and Far Field measurement system. To achieve the above three measurements, in addition to the necessary optical components and optical instruments, the core technology is to provide fast and stable current pulses to drive the VCSEL laser diode to emit light, and then to test various optical and electrical properties
-
Product
Optical Length Testers
-
Optical Wavelength Laboratories
The BOLT and VOLT Optical Length Testers from OWL offer a unique, economical alternative to users who need to measure the length of optical fibers. Rather than purchase expensive certification test sets, the BOLT can be added to an installer’s existing fiber test kit for a fraction of the cost.
-
Product
Master Compression Tester
CT166AK
-
Tests compression on all domestic and foreign cars and light trucks with gasoline engines, including mini engines. High quality 2-1/2" gauge features a dual scale dial with ranges from 0-300 PSI and 0-21 bar.
-
Product
Scratch Tester
-
Scratch testers from Anton Paar are used to characterize film-substrate systems and to quantify parameters such as adhesive strength and friction force by using a variety of complementary methods. This makes scratch testers invaluable tools for the determination of coating adhesion, scratch resistance, and mar resistance in research, development, and quality control.
-
Product
Drop Tester
AccuDrop 160A
-
Model AD-160A is 1 of 3 models in the ACCUDROPTM Series. It helps determine the ruggedness of packagesand the effectiveness of their interior cushioning when exposed to impact during material handling. Theeffects of dropping are easily duplicated in your laboratory using the controlled and precise flat, corner, andedge drop tests.
-
Product
Adhesion Testers
-
Adhesion testing is the best way to determine whether your films and coatings adhere to substrates the way you need them to.
-
Product
Earth Resistance Tester
-
PeakTech Prüf- und Messtechnik GmbH
A Rugged sealed digital earth tester is built with all the protection you need for outdoor use. The instrument is suitable for the testing of single earth electrodes such as lightning conductors and other small earthing systems according to VDE 0413. The resistance of conductors such as continuity and conduit coupling joints can also be measured. Two-terminal operation measurement, which reduces the accuracy, can also be done by shorting P and C terminals. It has an advanced circuit design that permits the instrument to operate with the minimum influence from earth voltage and earth resistance of the auxiliary spikes.
-
Product
Cable Testers
FiberMASTER
-
FiberMASTER provides optical loss (dB) measurements meeting Tier 1 certification requirements.
-
Product
Current Tester
MIG0624
-
The MIG0624 current tester is designed to test surge protection devices for low voltage applications (<1000 V). MIG0624 is a current generator delivering a 8/20 µs impulse up to 24kA. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied.
-
Product
CW Repeater Tester
MS 1108
-
The CW Repeater Tester is a computer-controlled system used to test CW Unit Electronics and its modules.
-
Product
CableEye Tester Calibration Verification Board | Cable & Harness Tester
CB50
-
Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently.
-
-
Product
ADSL/ADSL2+ Tester
-
ST332B tester is a multi-functional and hand-held ADSL2+ test instrument with small size, specially designed for xDSL line test (xDSL include: ADSL, ADSL2, ADSL2+, READSL etc) and maintenance.
-
Product
DIP Tester
Model DS-10
-
Putting it a conveyor to flow through a solder bath to obtain information needed to manage it. The created temperature profile makes it possible to monitor the 50ms sampling temperature of the preheat and solder temperature sensors in addition to the conventional management items.
-
Product
Network & Cable Testers
-
Detects PoE end/mid-span voltages on network cables. LED indicators instantly show “GO/NO-GO” detection on PoE networks. Plug cables directly into the builtin RJ45 jack or use the included patch card to detect voltage in wall jacks.
-
Product
Box Compression Tester
BCT-03
-
Jinan Leading Instruments Co., Ltd.
BCT-03 Box Compression Tester is professionallyused to test the compression resistance property of carton box, corrugated box,honeycomb cardboard box and other packaging. And it’s also applicable tocontainer compression test of plasticbucket (edible oil, mineral water), fiber drum, carton, paper, cans, containerbarrels (IBC barrels).
-
Product
Low Voltage Harness Tester
CR
-
Test complex assemblies with thousands of points. The system supports guided assembly with on-screen connector images, guidance LEDs on the assembly board, and immediate graphical and audible feedback to catch errors as they occur.
-
Product
Moisture Management Tester
TF128
-
TESTEX Testing Equipment Systems Ltd.
Moisture Management Tester, to measure the dynamic liquid transport properties of textiles such as knitted and woven fabrics in three dimensions
-
Product
Semiconductor Testers
-
Designing and manufacturing scalable Automated Test Equipment (ATE) targeted at testing SOC, MCU, RF PA/FEM, Sensors/MEMS and Power and Analog devices
-
Product
Audio Cable Tester
CBT-500
-
The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).
-
Product
WAN Tester
-
The Telinc WAN Tester is a sophisticated bit error rate tester in a compact, hand held package. It can test a wide variety of communications facilities and equipment including T-1, fractional T-1, E-1, fractional E-1, modems, multiplexers, CSU/DSUs, T-1 ESF CSUs, DU, NTUs and TIUs.
-
Product
Electrical Tester
T6-600
-
The electrical tester offers a variety of measurement options giving you an all-in-one troubleshooting tool. Measure true rms voltage and current from 0 to 200 A AC or 1 to 600 V AC or DC. You can also gather resistance measurement from 1 Ω to 2000 Ω. With the easy-to-read backlit display, you can keep see your work in dark environments and keep your most recent measurement on the screen with the HOLD button for easy viewing. The T6-600 also accepts optional Fluke TPAK Magnetic Meter Hanger for convenient operation.
-
Product
Temperature & Humidity Testers
-
Amprobe wireless temperature and humidity testers combine precise, accurate measurement of temperature and humidity with wireless communications up to 80 feet/25 meters to save time and steps. Measure and monitor temperature and relative humidity measurements over time using an Amprobe temperature and humidity data logger. These meters enable you to download measurements to your PC via an USB interface.
-
Product
Microhardness Testers
-
Newage Testing Instruments, Inc.
Newage Testing Instruments offers a range of microhardness testing solutions including the cost-effective MT91 and MS-ZH microhardness testing system.
-
Product
Capacitor Tester
MIG0603CAP
-
The MIG0603CAP consists of two circuits with impulse capacitance 20 µF and 0,25 µF. Both circuits generate a voltage wave shape 1,2/50 µs and are combined in a 4 unit height 19" rack. The generator circuits are defined in IEC 60384-14 and EN 132400. The serial resistors Rs, the impulse capacitor CT, and the load capacitance Cp will be automatically switched when different capacitance ranges are selected on the MIG0603CAP.
-
Product
CT Core Tester
VCCT
-
Veer make CT Core Tester VCCT is portable & easy to use Instrument. It is very useful to measure Voltage & Current of Electrical Steel like Toroidal Cores of different grade and size. VCCT is designed to test a lamination stack Toroidal Core. A Quality is judged by comparing the value of voltage applied & consumption of current.
-
Product
Two-Pole Voltage Tester
P-5
-
SONEL P-5 has all the features that characterize the P-4 Voltage Tester. In addition, the P-5 model has the ability to take resistance measurements up to 2 kΩ and has an LCD display that allows you to display the voltage and resistance values accurately.
-
Product
Multiple Impulse Generator
MIG0624LP1
-
MIG0624LP1 is a multiple impulse generator with four independent outputs each of 6kA and 1 Ohm source impedance. These are combined to deliver impulses up to 24kA. The impulses generated by this equipment are the 8/20µs and 10/1000µs current impulses. Typical applications would be testing of varistors, gas arresters and other surge protection devices.
-
Product
Pocket Network Tester
LinkSprinter®
-
The LinkSprinter Pocket Network Tester verifies the functionality of copper Ethernet links and identifies errors in less than 10 seconds. The tester reveals network connectivity status and port information while ensuring documentation for every link. The comprehensive AutoTester measures PoE voltage, performs a switch test, and confirms the DHCP server is running and responsive. The tester also verifies gateway/router, internal IP service, and cloud reachability. When paired with the secure Link-Live Cloud Service, the Network Tester automatically uploads results and allows annotation of results enabling job supervisors to easily manage the progress of deployment and troubleshooting tasks assigned to their team.
