Thermocouple Simulators
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Lightning Surge Simulators
LSS Series
-
A simulator to reproduce “High energy induced lightning noise” which is induced by potential change on the ground, or done to power lines or telephone lines as result of lightning current.This immunity test is required by major standards including IEC61000-4-5 and JEC 210/212 and is widely used in many industries.
-
Product
Tool, Locator, Thermocouple, ITA
910104135
Locator Tool
Used with Crimp Tool p/n # 910101102 to crimp thermocouple ITA contacts.
-
Product
MAX31855 J-Type Thermocouple Arduino Shield
SEN-30004-J47
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
Product
Multiphysics Simulator
-
The COMSOL Multiphysics simulation environment facilitatesall steps in the modeling process defining your geometry, specifying your physics, meshing, solving and then post-processing your results. Model set up is quick, thanks to a number of predefined modeling interfaces for applications ranging from fluid flow and heat transfer to structural mechanics and electromagnetic analyses.
-
Product
Modbus Test & Simulation Software
ModBus Constructor 1.7
-
Using Modbus Constructor you can quickly create a data management model for any of your Modbus devices. Unlike other available solutions on the market which provide displaying data as columns of abstract numbers of the same type, Modbus Constructor represents each data element exactly as you need. You may define type, format or scale independently. This makes them easy to read and analyze.
-
Product
Impulse Noise Simulators
INS Series
-
A simulator to reproduce fast rise-up noises which are generated when switching ON / OFF electric current on the inductive load. It can be used for performance evaluation of electronic equipment upon reproduction of line noises which are intruded to the power supply lines or induced noises onto the telecommunication lines.
-
Product
High Frequency Noise Simulator
SKS-H04GA
-
Shanghai Sanki Electronic Industries Co., Ltd.
The high-frequency noise simulation generator is an EMC test instrument that reproduces high-frequency noise with a fast rise time when the switch is turned on/off. Since the pulse rise time is less than 1ns and contains wide bandwidth noise, it is very suitable for reproducing malfunctions. The line noise entering the power line and the induced noise entering the communication line can be reproduced, and the performance evaluation of the malfunction and function degradation of electronic products can be performed.
-
Product
68HC11D Simulator
SIM11D
-
Simulate your M68HC11 microcontroller designs on your personal computer. Helps find hidden errors easily and efficiently.
-
Product
Eight-channel USB Voltage and Thermocouple DAQ
Model DI-2008
-
Includes DI-2008 instrument, WinDaq software, calibration certificate, terminal screwdriver, and USB cable (6-feet). Eight differential and isolated analog input channels. Seven bi-directional digital input ports, including: Counter input for totalizing applications, Rate input for frequency/flow/rpm applications. ChannelStretch™ channel expansion to 128 analog and 112 digital channels. Programmable voltage and thermocouple measurements per channel. 10 mV to 50 V programmable range per channel in 12 steps.
-
Product
K Thermocouple Immersion Probe
TP750
-
Immersion “K” Type thermocouple probe. Tolerance according to IEC 60584-2 standard.
-
Product
Thermocouples With Terminal Heads
-
Thermocouples with Terminal Heads including Mineral Insulated, Industrial Style & remote wall mounted housing thermocouples.
-
Product
Photovoltaic Array Simulation Solution
-
The Keysight N8937APV and N8957APV photovoltaic array simulators are capable of testing PV inverters up to 1,500 V, enabling designers to participate in the recent industry shift to the higher voltage. They can quickly simulate I-V curve characteristics under different environmental conditions (temperature, irradiance, age, cell technology and more), enabling the user to quickly and comprehensively test their solar inverters.
-
Product
High Intensity Pulsed Solar Simulator
GEN 2
-
Alpha-Omega Power Technologies, LLC.
The GEN 2 pulsed solar simulator and data acquisition systems can generate over 1,200 suns with a spot size of 12 mm x 12 mm at a rate of 2 pulses per second.
-
Product
Multi-channel GPS Signal Simulator
MP6220
-
*Up to 8 channels support positioning test*Can also be used as a single channel
-
Product
Cycle Drop Simulation Generator
-
Beijing KeHuan Century EMC Technology Co,.LTD
Cycle drop simulation generator
-
Product
VectorPro - Simulation Cyclizer for VCD to WGL/STIL
VectorPro
-
VectorPro is a low-cost, intuitive test development tool used to translate VCD/EVCD simulations into cyclized ATE Test Vectors in either WGL or STIL formats. This highly versatile tool reads in both VCD and EVCD formatted design simulations, and through the use of its flexible GUI, users are able to view and modify the simulation to fit the needs of their Test Environment.
-
Product
Environmental Simulation
-
During the development phase of new products, we analyze the weak points in simulation tests and test the products for environmental influences. The relevant standards are used as the basis for the simulation tests.
-
Product
Configurable Thermocouple Transmitter
HD778TR1
-
Configurable 4...20 mA/20...4 mA 2 wire temperature transmitter for K, J, T, N thermocouples.
-
Product
MIMIC NetFlow Simulator
-
MIMIC NetFlow Simulator generates a variety of flows and enables you to fully test your applications. Since you have a complete control over generated flowsets you can easily verify that your graphing application is correctly displaying the values and your collector correctly collects precisely generated flowsets.
-
Product
Gyro Simulator for Aircraft or Bench Use
TA-256A
-
This is a transformer isolated gyro simulator that can substitute for the KI256 attitude indicator and thus eliminate the requirement to remove that gyro to a remote stand and route a vacuum or pressure source out to the aircraft.
-
Product
Thermocouple Wires & Connectors
-
Is designed for sensor manufacturers for the production of commercial grade thermocouple junctions, and for users of large numbers of exposed junctionthermocouples such as test & development laboratories where multipoint temperature sensing of test pieces is required.
-
Product
Monitoring & Simulation
-
ETAP Power System Monitoring & Simulation (PSMS) is at the heart of the ETAP Real-Time power management system. Power System Monitoring & Simulation is the smart choice for both small and large electrical utility systems, generation plants, industrial sites, manufacturing facilities, and off-shore oil platforms.
-
Product
Synchro/Resolver Conversion & Simulation PMC boards
-
Versatile, rugged, and time saving Synchro/Resolver conversion and simulation PMC boards featuring multiple high accuracy, independent channels and easy programmability, to provide a highly accurate and convenient method to test and simulate positioning systems in lab and embedded environments. The SB-3642 conversion and SB-3644 simulation boards’ versatility and ruggedness enable them to be used first in the lab, and then be readily designed into embedded applications, just by the switch of a carrier card.
-
Product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30001-J
-
Breakout board for the MAX31855J digital thermocouple interface IC. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header, has a vertical mini thermocouple connector and four mounting holes for standoffs and 4-40 screws.
-
Product
DC/10 MHz – 18 GHz USB Thermocouple Power Sensor
U8481A
Power Sensor
The U8480 series is the fastest USB thermocouple sensor in the world without compromising the best in class linearity of the legacy 8480/N8480 series thermocouple sensors, all in a compact USB based form factor
-
Product
T-Type Thermocouple, 32°F to 500°F Temperature Sensor
745685-T02
-
T-Type Thermocouple, 32°F to 500°F Temperature Sensor - The T-Type Thermocouple works with NI measurement devices and software to help you acquire temperature data within a measurement system. You can use LabVIEW or FlexLogger software and NI-DAQmx driver software to configure … measurements and predefined scaling coefficients for the T-Type Thermocouple and acquire synchronized temperature data in units of degrees. The T-Type Thermocouple is available in various lengths and configurations including field-cuttable, ready-made sensors, and thermocouple wire extensions with a -20°F to 221°F temperature range.
-
Product
Solar Simulator
Unisim
-
TS-Space Systems is the first company to pioneer the use of metal halide sources in solar simulators for photovoltaic testing. The high temporal stability and close spectral match combined with the ability to control the output spectrum via multiple separate wavebands means the Unisim solar simulator is the only solar research tool designed for the accurate measurement of multiple junction devices, including the new generation of four junction devices. As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability. Using the latest HMI and halogen luminaire technology, the Unisim solar simulator provides a highly stable area of illumination. The simulators also use cutting edge filter technology in order to provide the best spectral match available for AM0 and AM1.5. Further to this, the spectrum can be achieved via two, three or four separate spectral wavebands which allows a high degree of spectral control for research and development. Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the instrument designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.
-
Product
Full-Featured Thermocouple and Voltage Measurement Instruments
EX10XX Series
-
A wide range of measurement types, including pressure, strain, temperature, position and voltage, can be performed using this instrument when combined with the EX10SC signal conditioning expansion chassis. Each input incorporates an independent signal conditioning path with software selectable filters for maximum flexibility.
-
Product
Local Loop Simulator 128 Channels
458-CC-16/458-CM
-
FEATURES: Accepts 1 to 16 Line Modules; User-Friendly Interface; Multiple Configurations; Field-Upgradeable Software; One-Year Warranty/Calibration. The 458 Series 16-slot Chassis, which consists of the 458-CC chassis and one of three control modules, provides a wide variety of configurations through use of up to 16 plug-in Line Modules.
