Ground Fault
-
Product
High Resistance Neutral Grounding Devices
-
HRG systems limit the fault current by placing high resistance between neutral point of transformer (or generator) and ground. As it is not possible to locate the fault point in delta connected systems, an artificial neutral point is created and delta connected system can be grounded. This allows a fault current of a few amperes thus locating the fault point gets easy. When the neutral point is grounded thru high resistance, both continuity of operation is provided during fault condition and sufficient current (typically between 2 A and 10 A) flow is provided for ease of locating the fault point.
-
Product
Fault Injection Module
WF 3154 C-Series
-
The WF 3154 from WireFlow is a 4-channel Fault Injection Module for Compact RIO. Each channel provide three solid state relays that can be used to create electrical fault conditions like: Open circuit, Short circuit to battery, Short circuit to ground.
-
Product
NI-9852, 2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
779707-01
CAN Interface
2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI-9852 is a fault‑tolerant Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9852 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9852 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9852 is only compatible with CompactRIO systems.
-
Product
Pole Mounted Detector of PtG and PtP faults in 6-69V Line
LineTroll 111K
-
The unit mounts 3-5m below the conductors and monitors all three phases. The indicator is powered by replaceable long-life lithium batteries which have a lifeexpectancy of 10-15 years. It provides a 360 degree visibility for indication both for transient faults and permanent faults.
-
Product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Single Channel
42-204-001
Multiplexer Module
The 40-204-001(PXI) and 42-204-001 (PXIe) are single channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault.
-
Product
Optical Visual Fault Locator
SAT-3C01
-
Shaanxi Aitelong Technology Co., Ltd
SAT-3C01 Optical Visual Fault Locator is used for optical identification, fault locating of SM fiber or MM fiber, which is a basic maintenance tool of optical network, LAN, FDDI, ATM optical system, and telecom network system, suitable for field working.
-
Product
3D Ground Penetrating Radar data processing & Interpretation software
Condor
-
Condor is modern processing, visualisation and interpretation software for the efficient management of Raptor 3D GPR array data.Boost performance and improve workflows.- Efficient sub-surface imaging- Effective workflows- Simple and intuitive- Dedicated to processing Raptor data- Modern Windows software (64-bit)
-
Product
12-bit, 4 Analog Current Outputs With Separate Grounds, Optically Isolated 500 V
APCI-3504-C
-
4 analog current output channels with 500V optical isolation, 12-bit resolution, each output has its own ground line.
-
Product
Detection of Earth Faults (PtG) and Short Circuit (PtP) Faults
CableTroll 2330
-
CableTroll 2330 is an indicator for detection of earth faults (PtG) and short circuit (PtP) faults on multi and single core cable terminations. The unit uses NorTroll type current sensors.
-
Product
Primary Cable Fault Locating
Directional Impulse Detector
-
The Directional Impulse Detector ( D.I.D.) is a compact handheld detector used to locate primary cable faults by sensing the magnetic field generated by the current pulse from a high voltage discharge device (thumper). A meter deflection indicates the intensity of the received signal. No deflection indicates that you have walked beyond the fault or away from the cable.
-
Product
USB-8501, 1-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786306-01
CAN Interface
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Programmable Ground Resistance Tester
-
AllWin Instrument Science and Technology Co., Ltd.
Executive test in 40A/60A of UL60950-1Test resistance range 0~510m ohmOutput current range 5~40A
-
Product
Power Quality Measurement & Digital Fault Recording
-
In view of the growing number of factors with a disturbing influence on power systems and the ever increasing sensitivity of devices and installations on the consumer side, simple monitoring criteria such as undervoltage or overcurrent are no longer adequate. Reliable registration of all the relevant processes within the electrical power system calls for constant observation of a wide variety of derived parameters, such as individual harmonic content, system unbalance and interharmonics, and the swift identification of even slight deviations from the norm.
-
Product
3U VPX 1 -Slot Power & Ground With VITA 67.1 Connector Installed J2
101V301P03-9002R
-
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
Product
Fault Locator
TRANSFLEKT
-
TRANSFLEKT simplifies the location of transient faults on the low voltage distribution network.
-
Product
Above Ground Insulator Tester / RF-IT
RF-IT
-
Hand Held InstrumentEasily locates shorted bolts, replaces bolt to boltUse on structure with or without CPUses Radio Frequency to test effectiveness of above ground insulatorsAuto Shut-Off feature
-
Product
7U VPX 1 Slot Power & Ground, 3.125G
101VPX701P-1X40R
-
3.3V, 5V and 12V power, rear connectors fully loaded. Use with Elma’s slot-to-slot or slot-to-I/O bulkhead cable products for system development.
-
Product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A
40-193A-001
Fault Insertion Unit
The 40-193A-001 is a 7-Channel Fault Insertion switch with one fault bus, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
Product
Visual Fault Diagnostics and Repair System
ScanExpress Viewer
-
ScanExpress Viewer™ is a printed circuit board (PCB) CAD data & photograph visualization tool for boundary-scan test development, electronic manufacturing test, and product repair environments.When combined with ScanExpress ADO™ (Advanced Diagnostics Option) for detailed results from ScanExpress Runner™, ScanExpress Viewer displays fault coordinates and connected traces superimposed directly on a board photograph or CAD layout diagram for expedient repair.
-
Product
Underground Cable Fault Locator
KM-CFPL-620 /620B
-
Kusam Electrical Industries Limited
“KUSAM-MECO” underground Cable Fault Pre-locator is an automatic Cable Fault Locator which adopts ARM, FPGA & Dot Matrix Color LCD display Technology. This tester combines both pulse reflecting technology (TDR) & (intelligent Bridge testing (Bridge) (Model-KM-CFPL-620B) for measuring the exact fault location such as broken line, cross faults, earthing, (poor insulation & poor contact of the lead covered cables as well as plastic cables. (Model-KM-CFPL-620B)).It is a microprocessor based fault locator with a user friendly menu. It is easy to operate. It tests almost all telecom & signal cables. It has an English menu which is easy to understand & use. With Megameter & Ohmmeter it enables to test insulation resistance & loop resistance. It has USB Port for uploading test data to computer
-
Product
3U VPX 1 Slot Power & Ground 25G Pass Through
101VPX301P-9X13
-
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
Product
Ground Testing
-
Ensuring an effective earth system is essential in a telecommunications system, and Megger is expert in earth testing having been there right from the start. These days Megger offers top end systems for design and soil surveys as well as tough easy to use testers for field engineers. We have tried to make the testers self checking as much as we can, to allow you to concentrate on collating and understanding the results.
-
Product
Cable Fault Locator
FaultCaster
-
Low Cost Full specification Professional Digital TDR Measures Distances to Open or Short Circuit Faults Extended Measuring Range to 2000m (6000ft) on all cable types Fast-Edge Step TDR technology for improved range & Resolution
-
Product
PXI Fault Insertion Switch, 7-Channel, Two Fault Buses, 20 A
40-194A-002
Fault Insertion Unit
The 40-194A-002 is a 7-Channel Fault Insertion switch with two fault buses, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
Product
Fault Locators
-
For the first time, you can detect the type of fault and locate the position of an electrical fault that causes intermittent or persistent circuit breaker trips, thus giving you the critical information needed to reduce call backs for circuit breaker trips.
-
-
-
-
Product
Fault Locator
REZAP FAULTMASTER
-
REZAP FAULTMASTER is an auto-recloser that keeps customers on supply during intermittent faults.
-
Product
7U VPX 4 Slot Power & Ground 10G Pass Through
101VPX704P-9X12R
-
Power for 3.3V, 5V and 12V are included, rear connectors areall fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
