Current Transducers
-
Product
Hall Effect DC Current Sensor
CYHCT-WS3
-
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-WS3 is a Hall Effect sensor for the measurement of DC current. The sensor has agalvanic isolation between the high power primary conductor and the secondary electronic circuit and withdifferent output signals and different power supplies.
-
Product
PXI/PXIe Wide Current Range Multiplexer Module, Dual 6-Channel, 2-Pole
40-514-104
Multiplexer Module
The 40-514-104 (PXI) and 42-514-104 (PXIe) are low density multiplexers in dual 6-channel, 2-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
Product
High Current Resistance Measurement Systems
-
Measurements International Ltd.
Modular Designed Base Unit with Expanded Capabilities to 10,000 Amp, Complete Turn-key System, Resistance and Temperature Curves, Complete Measurement Systems Available, Proven Technology.
-
Product
Laboratory EM current meter / water level and wave height meter
-
ACM2-RS and ACM3-RS are 2-D and 3-D electro-magnetic current meters for laboratory experiments. The models provide digital output, a high-speed sampling rate and insusceptibility to electro-magnetic noise. ACH-600RS is a highly sensitive capacitance water level meters. With the new system, a maximum of four different sensors can be connected to the compact interface unit, enabling simultaneous recording on a personal computer. Additionally, the system can provide analog output as well as necessary. While conventional water level and wave height meters cannot be used near velocity sensors, our instrument can be as near as 5 cm without increasing noise, due to its special isolated circuit. The result is an innovative system that is capable of achieving highly accurate data.
-
Product
Neodymium Low Frequency Transducers
-
High energy neodymium magnetic designs, complex cooling systems and new technologies for high-power handling, minimal distortion and low weight.
-
Product
Leakage Current Tester
-
Test Voltage : - 1V to 500V DC settableAccuracy : ± 1% of set Value ± 1digitLeakage Current : - Accuracy - ± 0.5% ± 1digitDigital Model – 19.99μA / 199.9 μA / 1.999mA / 19.99mAAnalog Model - 10μA /25μA/100 μA/1mA/2.5mA/10mASeparate Indication for Charge / Measure and Discharge modeAvailable in Digital Version Also
-
Product
AC Current Sensor
RCTi and RCTi 3ph
-
The RCTi & RCTrms sensors convert ac current to an isolated 0-5V voltage or 4-20mA current loop. TA5V-5A allows compatibility with existing 1A or 5A CT metering circuits. Both offer a choice of proportional (rms) and instantaneous outputs. The available RCT current ranges are 0-100A to 0-50,000Apk. Both RCTi and RCTrms provide accurate measurement over a wide bandwidth ensuring precise measurement even with harmonically distorted wave shapes - using a flexible clip-on sensing coil. The RCTs are available as single and three phase models.
-
Product
Current Transformers
-
Supreme Instrument Laboratories
Portable Low Tension precision grade multi ratio Current Transformers, housed in laminated wooden cabinet, wound primary with suitable terminals on highly insulated bakelite panel upto 100 Amps. For higher ranges, a centre hole is provided for passing primary conductors for desired range.
-
Product
Current Transformer
-
OutputDC 10VLinearityAs graph aboveApplied VoltageAC 2000V, 1min (between aperture and terminals)ImpendanceDC 500V, over 100M (between aperture and terminals)Fire Retardant Level94V0Output Terminals2.54 mm pinAnti-vibration50 Hz 5G
-
Product
Clamp type AC Current Sensor／for Low Leakage Current Measurements(ZCT Series)
ZCT-340SL
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Best sensor for low leakage current measurements of less than 1mA.*Suitable for low current measurements of terminal feeder.*High sensitivity and least affection from external magnetic field.
-
Product
Electromagnetic Ammeters And Voltmeters Fb-1, AC Electric Current, AC Voltage
-
ELECTROMAGNETIC DEVICES FOR MEASUREMENT OF ACTIVE VOLTAGE AND ACTIVE CURRENT.
-
Product
Device Current Waveform Analyzer, 1 GSa/s, 14/16-bit, 2 Channel
CX3322A
-
The CX3322A is a 2-channel model for engineers and researchers who just need one or two current waveform measurements at one time. Using a single channel current sensor (CX1101A, CX1103A) and a passive prove interface (CX1151A) enables power measurements. The bandwidth and the memory depth per channel are option and can be selected from 50 MHz, 100 MHz and 200 MHz, and 16 Mpts, 64 Mpts and 256 Mpts, respectively. The number of channels is not upgradable, but upgrade products for both bandwidth and memory depth options are also available for customers who need more performance after purchasing the product. You could also minimize the initial investment for later upgrade with this affordable 2-channel model.
-
Product
Current Mirrors
-
Analog Devices current mirrors are precision, high dynamic range, wide variable supply parts used for optical power monitoring, voltage biasing with current monitoring, and voltage-to-current conversion. Our current mirrors can monitor current down to as little as 3 nA and as much as 3 mA, with a linearity of 1% or better. The current dynamic range is 120 dB or 6 decades of current range, while the overcurrent protection feature in our devices forces the input pin to ground to avoid part damage. Over temperature (–40°C to +85°C) and process, the dynamic range only suffers 10 dB at the lower end of the range.
-
Product
Portable Voltage and Current Instruments
-
Each model in our portable test equipment range is designed for accuracy and reliability, providing high performance and ease of use for applications. Products are used in various lab and field applications across industries such as research and development, semiconductor, and process control. For higher range electrical source and measure we have a series of bench multifunction calibrators and multimeters.
-
Product
Multi-Channel, Programmable Current Source
CS-48-100
-
The Model CS-48-100 is a multi-channel, programmable current source. Developed for both semiconductor and digital superconductor electronics, it is computer-controlled and features 48 low noise current source outputs. Each source output has the capability to both set and read back currents and can be set to a zero current high Z mute state. Each of the 48 sources are optically coupled for control and are sourced from their own secondary winding for complete galvanic isolation. The device consumes a maximum of only 80 W and handles a maximum load current of 4.8 A total over all outputs. Operating over a range of 0-100 mA on each channel, the device features accuracy of +/-25 ?A. The mute state can be set thru a rear panel interlock or from the front panel button for maximum circuit protection. The unit can be mounted in a standard-sized rack.
-
Product
AC/DC Current Probe, 100 MHz, 15A
N2893A
Oscilloscope Probe
The Keysight N2893A is a 100 MHz bandwidth, active current probe for InfiniiVision and Infiniium oscilloscopes. The probe features flat bandwidth (DC-100MHz), low noise(<2.5 mA rms) and low circuit insertion loss. Auto demagnetization (degauss) and calibration removes any residual magnetism and unwanted DC offset in the probe. The probe is powered directly by the InfiniiVision and Infiniium Autoprobe interface, eliminating the need for an additional power supply.
-
Product
DC Bias Current Source
TH1778AS
-
Changzhou Tonghui Electronic Co., Ltd.
■ Test Frequency: 0Hz - 2MHz ■ Provide 0~20A of constant current output, and must be controlled by TH1778A ■ Support 6 machines on line at most and
-
Product
Flexible Monitoring of Voltage & Current in A 2 B ® Networks
Line Test Box LTB 1024
-
The Automotive Audio Bus (A 2 B ® ) from Analog Devices Inc. reduces the complexity of audio systems. In addition to the automotive industry, it is also increasingly being used in other areas such as conference systems. We have developed a line measuring device specifically for this A 2 B ®technology: the Line Test Box LTB 1024.
-
Product
Current Probes
XQ13
-
Beijing GFUVE Electronics Co.,Ltd.
The model XQ13 ac micro amp clamp on current probe is suitable for 10A-100A cable online measurement, it belongs to high performance current sensor field.
-
Product
Current Input0 to 20mA
TGPR-0804
-
Current input data logger. A current input data logger that is housed in a robust, waterproof (IP68) rated case. The TGPR-0804 can be used to record the output from a number of industry standard 4-20mA sensors. Common applications include pressure and flow rate monitoring.
-
Product
High Line Pressure Transducer with Digital Interface
P368
-
The Validyne model P368 is a digital differential pressure transmitter designed for high line pressures and industrial pressure measurement applications. Full scale ranges of 8 psid to 10,000 psid are available. The on-board microprocessor provides high accuracy and improved stability in changing thermal environments. Communication via RS485, USB or CanBus provides remote zero and span adjustment as well as digital pressure readings in engineering units.
-
Product
DC Constant Current Source
-
SCR ELEKTRONIKS have developed equipment namely“DC CONSTANT CURRENT SOURCE”. The system comprises of Constant Current Sources having ranges: 900A continues & 3000A short time at 8V maximum.
-
Product
SY024 Pulse Rate to Current or Voltage Converter
-
SY024 PR* is a Pulse Rate-Analog converter designed to accept a frequency and produce a proportional Current or Voltage output. The current output can be 0-20mA or 4-20mA and the voltage output version is user adjustable from 0-5V to 0-10V.
-
Product
Arbitrary Current Generator Family
PXA(e)73xx
-
The PXA(e)73xx ArbGen family features up to two simultaneously working channels with 100MS/s, 16Bit resolution and an output current up to 30mA in sink mode (at up to 30V) or ±20mA in combined source/sink mode (at up to ±10V).Every channel is equipped with 2MB memory. The whole amount of 1 million samples can be partitioned into one ore more waveform segments. Depending on the number of channels and the floating option, the Arbitrary Function Generators are built into a compact 3U PXI(e) device for 1 or 2 slots.
-
Product
Closed Loop Precise Hall AC/DC Current Sensor
CYHCS-LF
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used for accurate measurement of DC and AC current, pulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
Product
500A AC/DC Current Sensor
CT6904
-
Hioki pull-through AC/DC current sensors are best-in-class devices for use with power analyzers,, Memory HiCorders and high performance oscilloscopes. The CT6904 is a DC to 4 MHz/500A sensor, ideal for capturing current signals from switching power supplies, inverters, power conditioners, etc.
-
Product
Contactless Torque Transducers
RS425
-
These contactless Torque Transducers are not limited by operational speeds, can fit any shaft and capable of measuring torque from 1nm and up to 500knm, providing highly accurate and reliable torque measurement in many applications.
-
Product
High Speed Response, High Accuracy DC Leakage Current Sensor
DCZCT-20CDHL
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Low DC current measurements.*DC1mA～200mA*High accuracy.*±1%F.S ±10mV*Least influence of magnetization.*Less than DC1mA in current level*Convenient +5V single polarity power supply.*Reference voltage (Vref) terminal is equipped.
-
Product
3-Phase AC Voltage Transducer
ENVIROMUX-PT3-600
-
Monitors and reports voltage of any 3 phase circuit. Remotely detect blown fuses or tripped circuit breakers. Three 600 VAC inputs, three 4-20 mA outputs. Inputs and outputs isolated from one another. Frequency: 50/60Hz. Maximum primary current: 600 volts. Accuracy: ±0.25% F.S. @60Hz. Output: 4-20 mA. "Zero" adjustment for accurate 0 VAC reading, and "Calibration" adjustment for frequency and voltage level. Powered by the ENVIROMUX-S420MA-24V. Regulatory approvals: UL, CUL, CE. Requires two ENVIROMUX-S420MA-24V to monitor three phases. Caution: installation should be performed by qualified electricians only. Make sure electrical service is disconnected before making any electrical connections.
-
Product
5 Amp High Accuracy Current Probe
HA5
-
Our HA5 Current Probe covers the measurement range from 20 milliamps to 5 amps, making it the best choice for measuring very small loads and the outputs of CT (Current Transformer) step-down circuits.
