Multifunction DAQ
-
Product
DB25F-DB25F, 25-Pin D-Sub Cable for SMUs, Low Leakage, 2 m
782015-02
Multifunction Cable
DB25F-DB25F, 25-Pin D-Sub Cable for SMUs, Low Leakage, 2 m
-
Product
PXIe-6363, 32 AI (16-Bit, 2 MS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module
781056-01
Multifunction I/O
The PXIe‑6363 offers analog I/O, digital I/O, and four 32‑bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6363 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
SH68-68-EPM Shielded Cable, 68 D-Type to 68 D-Type, 0.35m
199006-0R35
Multifunction Cable
68-Pin Female to 68-Pin Female, Twisted Pair, Shielded Multifunction Cable - The SH68F-68F-EPM Cable, sometimes referred to as SH68-68-EPM, connects NI DAQ 68-pin devices to 68-pin accessories. The SH68F-68F-EPM Cable has D-type connectors and is offered in different lengths.
-
Product
3U cPCI I/O & Comm Board
75C3
Multifunction I/O
NAI’s 75C3 is a 3U cPCI multifunction I/O and communication board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed A/D channels and 28 Discrete I/O programmable channels, or with a reference supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
SH37F-Tajimi Shielded Cable, 10M
199254-10
Multifunction Cable
37-Pin D-SUB Female to 4 7-Pin Tajimi Female, C Series Strain/Bridge Input Module Multifunction Cable - The SH37F-Tajimi connects with compatible sensors to accessories or cables with Tajimi push-pull connectors.
-
Product
Multifunction I/O Device
Multifunction I/O
The Multifunction I/O Device features I/O with varying channels, sample rates, output rates, and other features to meet many common measurement requirements. You can use the device for industry applications such as laboratory automation, research, and design verification. The included DAQExpress companion software provides basic measurement and analysis, while the included NI-DAQmx driver provides the ability to create customized automated measurement and control applications. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
PXI Based Multifunction Measurement and ICT Instrument
PXI-501
Multifunction Switch/Measure Unit
The PXI-501 is a multifunction measurement instrument for functional and in-circuit measurements.It combines two parametric measurement units with a digital voltmeter, a high voltage current source and a discharge unit. This powerful combination makes it the ideal instrument for classical analog in-circuit test and manufacturing defect analysis with additional functional test capabilities.With it’s fast sampling rate of up to 4MSps it speeds up measurements and is capable of measuring and generating AC signals up to 100kHz.To enhance the PXI-501 capabilities it can be combined with an ABex TM-501 or an ABex TM-404. The ABex TM-501 enhances the in and output range of the PXI-501. Furthermore, it provides a shunt current measurement upgrade. In combination with the ABex TM-404 it’s a complete in-circuit test solution with 86 channels in one ABex slot. For sure it can be upgraded to 2838 test points in one rack by simply adding additional matrix modules.With the above-mentioned terminal modules, the PXI-501 is able to act as a ABex system controller, so that no additional controller is required in the cassis.
-
Product
PXIe-7868, Kintex-7 325T FPGA, 18-AO Channels, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
785571-01
Multifunction Reconfigurable I/O
Kintex-7 325T FPGA, 18-AO Channels, 1 MS/s, PXI Multifunction Reconfigurable I/O Module—The PXIe-7868 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of timing and synchronization. With 18 analog output channels connected directly to a Kintex-7 325T FPGA, you have ample space to design applications that require precise timing such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe-7868 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe-7867 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
Product
SHC68-C68-S, 68 pin VHDCI to 68 pin VHDCI, 2m
186380-02
Multifunction Cable
SHC68-C68-S, 68 pin VHDCI to 68 pin VHDCI, 2m
-
Product
Kit, Cable Assembly, SH-37F-OM6/4, 9219 Calibration Cable Kit
146907-01
Multifunction Cable
Kit, Cable Assembly, SH-37F-OM6/4, 9219 Calibration Cable Kit
-
Product
SH37F-Tajimi Shielded Cable, 1M
99254-01
Multifunction Cable
SH37F-Tajimi Shielded Cable, 1M
-
Product
USB-6341, 16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device
782251-01
Multifunction I/O
16 AI (16-Bit, 500 kS/s), 2 AO (900 kS/s), 24 DIO USB Multifunction I/O Device - The USB‑6341 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6341 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI-6284, 32 AI (18-Bit, 625 kS/s), 48 DIO, PXI Hybrid, Multifunction I/O Module
779122-01
Multifunction I/O
32 AI (18-Bit, 625 kS/s), 48 DIO, PXI Multifunction I/O Module—The PXI‑6284 offers analog input, correlated digital I/O, two 32‑bit counter/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
SH68-68R1-EP, Shielded Cable, Right Angle Connector, 1 m
187051-01
Multifunction Cable
68-Pin Female SCSI to 68-Pin Right-Angle Female SCSI, Twisted Pair, Shielded, 1 m Multifunction Cable - The SH68F-68R1F-EP Cable, sometimes referred to as SH68-68R1-EP, connects NI DAQ 68-pin devices to 68-pin accessories. The right-angle connector is useful for small spaces where clearance is limited.
-
Product
2-Channel DAQ Module
FMC142
-
Sundance Multiprocessor Technology Ltd.
The FMC142 is an analog-to-digital (A/D) and digital-to-analog (D/A) FMC daughter card that provides two 16-bit A/D channels at 370MSPS and two 16-bit D/A channels at 2.5GSPS which can be clocked by an internal clock source (optionally locked to an external reference) or by an externally-supplied sample clock. A trigger input is also available for customized sampling control. The FMC142 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1-2010). It offers front panel analog I/O access and can be used in a conduction-cooled environment.
-
Product
PXI-6120, 4 AI (16-Bit, 800 kS/s/ch), 8 DIO, PXI Multifunction I/O Module
78396-01
Multifunction I/O
4 AI (16-Bit, 800 kS/s/ch), 8 DIO, PXI Multifunction I/O Module - The PXI‑6120 is a simultaneous-sampling, multifunction data acquisition device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. It is ideal for a variety of applications, such as stimulus/response applications for whih synchronization among analog input, analog output, and digital I/O is required; 42 V automotive applications; radar; sonar; and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
3U OpenVPX SOSA™-Aligned MFIO-Intensive Processing Board
68G6
Multifunction I/O
The 68G6 is a SOSA™-Aligned 3U OpenVPX board that can be configured with up to three NAI smart I/O and communication function modules. In addition to the standard expansion plane (EP) PCIe and control plane (CP) Ethernet control interfaces, the 68G6 facilitates convenient external access to supported NAI PCIe function modules through its 1 x1 PCIe interface, enabling seamless expansion of host SBC functions for enhanced project solutions, while also offering external access to supported NAI FMx modules via a SATA II interface. The 68G6 is on NAI’s certifiable product development roadmap supporting DO-178C and DO-254 design assurance guidelines for safety-critical applications. Ideally suited for rugged Mil-Aero applications, the 68G6 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
1-Channel DAQ Module
FMC170
-
Sundance Multiprocessor Technology Ltd.
The FMC170 is an analog-to-digital (A/D) and digital-to-analog (D/A) FMC daughter card that provides one 10-bit A/D channel at 5Gsps and one 10-bit D/A channel at 5Gsps. The sample clock can be supplied externally or by an internal clock source (optionally locked to an external reference). The clock tree enables cascading of multiple boards for phase-locked sampling. A trigger input is also available for customized sampling control.
-
Product
Multifunctional testers
MI 3100 SE EurotestEASI
-
MI 3100 SE EurotestEASI is a fast, accurate and easy to use multifunctional measuring instrument which performs a complete set of installation safety tests according to IEC/EN 61557. Besides, the MI 3100 SE EurotestEASI enables on-line voltage monitoring, phase sequence testing and earth resistance measurement. EurotestEASI is equipped with integrated characteristics of fuses and RCDs for PASS / FAIL evaluation of test results.
-
Product
PCI D/S, S/D, I/O & Comm Board
76CS3
Multifunction I/O
NAI’s 76CS3 is a PCI/PCIe multifunction I/O and communication board designed for applications requiring Digital-to-Synchro/Resolver (D/S) and Digital-to-LVDT/RVDT (DLV) stimulus output, as well as I/O and communication functions. This full-slot board contains five independent, function module slots. The board can be configured for 6 separate D/S channels, or for D/S in combination with I/O and communication modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
Multifunctional testers
MI 3102 BT EurotestXE
-
MI 3102 BT EurotestXE is a multifunctional measuring instrument which performs a complete set of installation safety tests according to IEC/EN 61557. It supports AUTO SEQUENCE® testing of the TN, TT and IT earthing systems. ISFL measurements and the IMD tests can be performed. Besides, the MI 3102 BT EurotestXE enables on-line voltage monitoring, phase sequence testing, earth resistance measurement, illuminance measurement and TRMS current measurement. EurotestXE is equipped with integrated characteristics of fuses and RCDs for PASS / FAIL evaluation of test results.
-
Product
Multifunction Calibrators
-
These field and bench calibrators source, simulate, and measure pressure, temperature, and electrical signals with exceptional precision. They can automate calibration procedures, store data, and even calibrate and troubleshoot HART-compatible devices. Our bench calibrator can even be used to calibrate our field calibrators. Also find here 5.5- and 6.5-digit bench multimeters for to assist with a variety of general test and calibration applications.
-
Product
Multifunctional testers
MI 3152H EurotestXC 2,5 kV
-
MI 3152H EurotestXC 2,5 kV is an instrument from the new generation of Metrel’s multifunctional measuring instruments. The already well known functions like complete installation safety testing according to IEC/EN 61557 and AUTO SEQUENCE testing of TN and TT earthing systems expanded with insulation resistance measurement with the test voltage up to 2,5 kV are managed by a completely new user interface based on large colour touch screen display.
-
Product
Multifunctional Meter
AEM-DD
-
AEM-DD provide high accuracy DC power measurement,display and remote communication of five loops(V,A,P,Kwh). Multi-circuit designand relay output modular expansion design decrease the overall cost and make the functionality more flexible.
-
Product
Multifunction Reconfigurable I/O Device
Multifunction Reconfigurable I/O
Multifunction Reconfigurable I/O Devices feature a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware-in-the-loop (HIL) testing, custom protocol communication, sensor simulation, and high-speed control.
-
Product
Multi-Function Recorder
DR-300
-
The DR-300 is the only tool you need to capture and diagnose power system anomalies, and meets regulatory compliances including PRC-002-2. With multiple recording modes and continuous transient oscillography, you will never miss an event. The DR-300 captures high speed transients and long term system disturbances with enough memory to give you a complete view of the system disturbance. While simple and quick to set up and diagnose a fault; it has the power to analyze complex system anomalies.
-
Product
PXIe-6355, 80 AI (16-Bit, 1.25 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module
783632-01
Multifunction I/O
PXIe, 80 AI (16-Bit, 1.25 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6355 offers analog I/O, digital I/O, and four 32‑bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6355 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
DAQ- Data Aquisition Boards
ETS Series
-
The ETS Series products are designed to create a simple "Go, NoGo" test platform that executes quickly and requires minimal Operator interaction. Low-cost alternative to traditional PC-based test equipment. Test Electronics sources and stocks a large variety of data acquisition and sensor boards to make your hardware build quick and easy. Develop your own embedded test system or use the embedded test systems we have developed.
-
Product
PXIe-6259, PXIe, 32 AI (16-Bit, 1.25 MS/s), 4 AO, 48 DIO, PXI Multifunction I/O Module
779778-01
Multifunction I/O
The PXIe-6259 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Multifunctional Meter
CPM-12
-
CPM-12 multifunction power meter provide high accuracy single phase and three-phase measuring and displaying, energy accumulating, power quality analysis, and data communication.Hardware can be option a a RS485 Modbus communication port.Auto wiring change (Note) via softwareCE and FCC approved
