Current Detectors
-
Product
Integrated Current Sensors
-
Current sensors have to be smaller, smarter, cheaper. LEM’s R&D is actively developing a range of ICS to reduce the footprint of the current sensing function and simplify the integration of current measurement in a wide range of applications in automotive, industrial, or residential.
-
Product
Constant Current System
CCS-BTA
-
Vernier Software & Technology, LLC
The Constant Current System is a DC power source with a built-in current probe designed for use in electrochemistry experiments.
-
Product
SF6 Leak Detector
KVWG-II
-
KV Hipot Power Test Equipment Co.,Ltd
SF6 Leak Detector can quickly and accurately quantitatively detect the leak points of SF6 circuit breakers, GIS and annual leak rate.
-
Product
DC Current Bias Supply
DC1000A
-
To guarantee the quality and performance of inductive components such as inductors, chokes and transformers they are tested at their real-life operating point. If the inductor is designed to carry a DC current, then its inductance must be measured with that DC current present. Until now, these measurements were made by an LCR meter connected via special interfacing to a DC bias supply available only from the manufacturer of the LCR meter. The unique NEW DC1000A can be used with any precision LCR meter and connects simply into existing test fixturing.
-
Product
RMS Responding Power Detectors
-
Recognized as the pioneer and leader in RF detectors, Analog Devices offers a broad portfolio of high performance logarithmic amplifiers and TruPwr™ rms responding detectors. ADI logarithmic amplifiers measure signals up to 100 dB dynamic range, from dc to microwave, and accuracies of ±0.2 dB, and are well-suited for both RSSI and transmit power level detection. The TruPwr rms detectors address the challenge of measuring complex waveforms found in spread spectrum CDMA/W-CDMA and higher order QAM modulation systems and provide an accurately scaled dc voltage, which is the rms equivalent of the input waveform.
-
Product
20 Amp Current Transformer Burden Test Set
1044A
-
Due to overwhelming demand, TESCO is pleased to re-introduce the 1044A 20 Amp Current Transformer Burden Test Set. This light weight, hand held unit is a simple and inexpensive means whereby a current transformer installation may be quickly checked for many sources of trouble. The 1044A provides utilities a less expensive and more traditional option for checking larger services for potential meter circuit related issues.
-
Product
Multi Channel Linear Vibration Motor Current Isolation tester
BK2017
-
The BK2017 Current and Isolation Tester was designed as a single purpose machine for quickly testing up to 8 linear vibration motors at a time. You can test current and isolation without checking other characteristics of the motor. With its simple design, it is very easy to use and the results appear clearly on the screen in about half a second. And with only 2 cables to connect, it can quickly be plugged into an automatic loader/sorter for even faster results!
-
Product
Temperature Measurement IR Sensors & Detectors
S25 TO-5
-
A single-channel silicon-based thermopile that offers the smallest single element active area size at 0.25mm x 0.25mm in a TO-5 package. Delivers a fast 18ms time constant in Argon encapsulation gas and even faster with Neon gas at 9ms. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-3000
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra big CT window*AC 1A～3000A*Current measurements of main cable
-
Product
Ultrafast Photodetector with Current Monitor, 1250 - 1650 nm, DC - 20 GHz, FC/PC
DXM20AF
-
The DXM20AF Ultrafast Detector is a DC - 20 GHz, fiber-coupled, InGaAs-based photodetector designed for applications in the 1250 nm - 1650 nm wavelength range. The core element of the detector is the fiber-coupled, hermetically sealed, microwave detector module. For convenience and simplicity of use, the module is mounted inside a rugged housing that includes a rechargeable battery, current monitor circuitry, and a digital display of the DC photocurrent.
-
Product
AC/DC Clamp-On Current Transformers
-
AC/DC Clamp-On Current Transformers by AYA Instruments
-
Product
Stealth In-Foil Metal Detector
-
Stealth In-Foil metal detectors are custom manufactured to suit any foil packaging application or aluminum casting inspection. The Stealth uses digital signal processing technology and has high sensitivity levels to ensure the detection of the smallest ferrous contaminants, despite the presence of foil packaging. The built-in data collection software with USB data transfer establishes the Stealth as an effective critical control point complying with stringent HACCP regulations.
-
Product
Clamp type DC/AC Current Sensor／with Voltage Output
LAD-240
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*With DC voltage output*DC 1A～200A
-
Product
Ultrafast Photodetector with Current Monitor, 700 - 870 nm, DC - 12 GHz, FC/PC
DXM12CF
-
The DXM12CF Ultrafast Detector is a DC - 12 GHz, fiber-coupled, GaAs-based photodetector designed for applications in the 700 nm - 870 nm wavelength range. The core element of the detector is the fiber-coupled, hermetically sealed, microwave detector module. For convenience and simplicity of use, the module is mounted inside a rugged housing that includes a rechargeable battery, current monitor circuitry, and a digital display of the DC photocurrent.
-
Product
Schottky Mixer And Detector Diodes
-
Majority carrier diodes formed by plating a layer of metal on a layer of doped semiconductor, which forms a rectifying junction.
-
Product
SF6 Leakage Detector
GDWG-IV
-
GDWG-IV SF6 Gas Leak Detector is infrared type leak detector. It is color LCD display and real-time shows SF6 concentration. It rapidly detect SF6 breaker, GIS leakage point and yearly leakage rate qualitatively and quantitatively. It's a good device suitable for power supply department, installation and overhaul unit, power test institute.
-
Product
GAOTek Portable H/L Voltage Clamp Current Leaker
GT00YA00ZX
-
The GAOTek Portable H/L Voltage Clamp Current Leaker measures high voltage current with a 12.5 in (32 cm) insulating rod, adopting the latest CT technology and integrating mask digital technology. This instrument provides high precision, reliability, and stability with its integrated design between transducer clamp and domain. This leaker can be used to measure any wire with or without the insulation layer where the voltage is below 10 kV. The insulating rod is portable, moisture resistant, heat resistant, shock resistant, and insulating. It provides additional functionalities such as online current testing, peak and data holding, data storage, detection of high and low current in primary and secondary circuits separately, and provision of suitable calculations to conclude change in high and low pressure.
-
Product
Clamp type DC Current Sensor／for DC Leakage Current Measurements
DCZCT-110S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size, General purpose*DC leakage current measurements
-
Product
Partial Discharge Detector
APD-ANNUNCIATOR
-
The APD-ANNUNCIATOR is a remote partial discharge detection equipment inside any energized cabinet. The probe is installed in the unit under test, instantly reporting its status. This equipment gives a great benefit because it avoids long term damage to the switching equipment.
-
Product
Current Sensor For Outdoor Use
CT-41B
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Equivalent to protection grade IP67
-
Product
Split type AC Current Transformer
CTS-300
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*5A output for metering application.*Short circuit switch for secondary output is provided for safe operation.*High accurate transformer for the application of first class meter.*Easy to install by metal fitting.
-
Product
Low Input Bias Current Op Amps (≤100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
Logger Version 2-D Electro-Magnetic Current Meter for Deep Ocean
INFINITY-Deep AEMD-USB
-
INFINITY-Deep is an autonomously deployable data logger for current speed measurements in the deep oceans. The currents in the deep oceans are very weak. It is too hard to accurately measure the deep water currents by some ADVs (Acoustic Doppler Velocimeters) that detect the Doppler-effect by scatter with the suspended particles in the water, because the concentration is very low.
-
Product
Rogowski Coil Current ProbesTOP
-
*Switching current waveform and pulse response characteristics of power devices*Current measurements of inverter system*AC current measurements (at large DC offset)*Impulse high current measurements*Bus Bar high current measurements
-
Product
Current Injection Sets
-
Built in c based Time Interval Meter measuring from1 millisec to 9999 sec. Panel with easy and clear legends to read. Continuosly variable outputs. Auto Cut-off & output isolated. Self sensing of contacts i.e. NO or NC Potential free star stop signals Available in Portable / Lab type models with metal cover
-
Product
Industrial Current Sensors
RCT
-
Power Electronic Measurments Ltd
The RCT range of AC current transducers are designed for permanent or semi-permanent installation and are available with industry standard outputs.
-
Product
Custom Detectors
-
Besides the described types Inphora can supply detector-filter combinations with parameters matching the customer's special requirement, with different sized housing, without housing. If the application determines the detector's spectral responsivity, we can achieve that with a filter designed exactly to the specifications. CCD cameras with unusual spectral sensitivity functions can be matched with filters to obtain CIE tristimulus response or photopic response. Similarly, photmultiplyers can be matched also with INPHORA filters. When determining parameters for a custom detector-filter combination several details have to be considered:
-
Product
Current Shunt Module
CURS100
-
The CURS100 converts a current signal output by a sensor or output device (e.g., 4 to 20 mA) to a voltage that can be measured by a datalogger. The 100 ohm resistor used for the current shunt allows currents up to 25 mA to be read on a 2500 mV range (CR10, CR10X, CR510, CR500) and currents up to 50 mA to be read on a 5000 mV range (CR23X, 21X, CR7, CR5000, CR9000, CR9000X).
-
Product
AC Current Isolated Sensor Two / Four Wire Transducer
TSCT (Average Sensing) / TFCT (TRUE RMS)
-
Kusam Electrical Industries Limited
• Transform Input: AC 5~400A directly into DC 4~20mA, no need external CT.• Suitable for application with high waveform distortion :(Frequency converter, Motor, SCR )• High accuracy ＜0.5%• High response time• High stability, easy connection.
-
Product
Partial Discharge Detector
PDD 100
-
The Insulator partial discharge detector is a state-of-the-art technology used by NASA. The Parabolic design of the disc helps to maintain and detect ultrasound from safe distance of 100 Meters. Enhanced ultrasound detection is provided to the device, by combining the features of the already proven Ultra sound sensing technology with extended range and sensing capabilities. A pistol like grip laser pointer, and rifle sights make the Insulator partial discharge detector easy to handle and use.
