Programmable Voltage Sources
-
Product
PXI-4130, ±20 V, ±2 A DC, 40 W PXI Source Measure Unit
779647-31
-
±20 V, ±2 A DC, 40 W PXI Source Measure Unit - The PXI‑4130 is a programmable source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4‑wire) sense. With its five current ranges, it is ideal for transistor characterization that requires accurately sourcing a constant current or voltage while sweeping another current. The PXI‑4130 also includes a utility channel that can source either current or voltage. This PXI SMU can act as either a constant voltage source or a constant current source, with a settable compliance limit for either mode. In addition, you can enable remote sense on the SMU channel to maximize voltage output and measurement accuracy on your device under test (DUT) for high-precision applications.
-
Product
Multi-module Programmers
-
Xeltek offers both traditional gang programmers and modern stand-alone models for production cluster setups. Traditional gang programmers come with four independent sockets that allow chips to be programmed concurrently.Recent trends have shifted from gang programming to cluster setups. Cluster setups consist of multiple stand-alone programmers operated by one operator for enhanced efficiency and cost-savings during production.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-156
-
The 40-297A-156 (PXI) and the 42-297A-156 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 85.3 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Argon Calibration Source
AR-1
-
The AR-1 produces low-pressure argon emission lines from 696-1704 nm for use in performing fast, reliable spectrometer wavelength calibrations.
-
Product
PXI Precision Resistor Module 2-channel 10 to 36k
40-261-002
-
PXI programmable resistors featuring fine resistance setting resolution and excellent resistance stability and accuracy through the use of advanced switching networks and software correction techniques. The two modules in this range support two identical resistor channels that can be set to values of between 1.5Ω to 2.9kΩ or 10Ω to 36kΩ with a precision of better than 2mΩ (40-261-001) or 15mΩ (40-261-002- this version) making them ideal for simulating sensors that can be accurately controlled to fine values.
-
Product
Medium Voltage Drives
-
Target markets include Oil and Gas, Water and Wastewater, Power Generation, Rubber and Tire, Mining, Cement and other industrial applications. They can be applied equally well to applications requiring Constant Torque (CT) output performance as well as the traditional Variable Torque (VT) pump and fan loads.
-
Product
ISP Programmer Superpro Is01
-
Features:Until now,Support IC manufacturer, pcs devices and keeps growing.1)High speed thanks to the flexible hardware engine. Programming speed adjustable for complicated application environments brought by user target board, length of ISP cable etc.2)Stand-alone and PC-Hosted (USB2.0 High Speed) dual mode;3)Supports ISP programming of devices with I2C, SPI, UART, BDM, MON, MW, JTAG, CAN, ICC, RS232 and any other serial port.4)ATE interface;5)Over-current and ESD protection to protect your equipment;6)DLL and API for easy integration into customers’ system.Hardware Specifications:1) ISP cable integrates I2C, SPI, UART, BDM, MON, MW, JTAG, CAN, ICC, RS232 interfaces。2) VDD (0-5.5V /0.5A) and Vpp (0-15V / 0.2A) lines provided to power the target board and the target devices.3) Cable driver circuit supports target devices of voltage level 1.5-5V and is ESD protected.4) USB 2.0 (high speed) interface for PC hosted mode and management of project files on SD card.5) A 20 Characters x 4 lines LCD and a 6-key keypad are built with it for stand-alone operation. In stand-alone mode project files are stored on the SD card (up to 16GB). The number of the project files is limited only by the capacity of the SD card.6) ATE interface is built for easy external hardware control. 6 lines SEL0-SEL5 are for project selection (maximum 64 files); 2 command lines START and STOP; 3 STATUS lines PASS, FAIL and BUSY. All signals are optical-isolated.7) A universal AC adaptor of DC12V/2A is included for power supply.8)WINDOWS XP/Vista/Win7/Win8/Win10 32/64bit compatibility.Software Specifications:1) Supports almost all devices with ISP interface.2) Supports Jam and Staple files from ACTEL and ALTERA; Direct C files from ACTEL.3) Programming speed selectable (High, Normal and Low) for complicated applications such as different cable lengths, different target load characters.4) Dynamic buffer function. Application examples include device S/N, MAC address, frequency or transducer calibration etc.5) File format on SD: FAT16, FAT32.6) Functions for IP protection: Project security, SD security, batch control, administration management etc. 7) API and DLL provided for easy integration into customers’ system like ICT and ATE.8) Software provides the features for multiple units to work concurrently controlled by USB HUB.Applications:1)R&D application like in-circuit test and debug.2)Volume production. Devices may be programmed after the board is fully assembled. One example is the serial number writing to an on-board serial device.3)Field application. Comes with portability, stand-alone mode and mobile data storage media (SD card), it is suitable for field test, debug and data acquisition.4)Third application modules. Friend s/w interface (DLL and Virtual Com communication command set) and h/w interface ( ATE and USB) are provided and make it very easy for customers to integrate ISP01 as a functional module into their systems. One example is the ICT equipment. With this integration user can finish in-circuit test and in-circuit programming in one step.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 63.7 Ohm
40-294-011
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Broadband Optical Source - PXI
SLED 1000 Series
-
The SLED 1000 Series is a super-luminescent LED light source with high output power, large bandwidth and low spectral ripple. It comes in various wavelength models to address applications in the telecom and datacom markets.The SLED is a single-slot PXIe module and is ideal for building a customized optical testing platform that delivers reliable and repeatable results in manufacturing or R&D environments.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-045-HI
-
The 40-230-045-HI (PXI) and 42-230-045-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 2.954MΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Noise Source Family
SNS Series
-
Works in conjunction with the NFA Series of noise figure analyzers to simplify measurement set-up and improve accuracy and reliability, automatically downloading electronically stored calibration data.
-
Product
PXI Resistor Module 2-Channel 2R to 16.3k
40-293-031
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-255-HI
-
The 40-230-255-HI (PXI) and 42-230-255-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 43.424MΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-141-HI
-
The 40-230-141-HI (PXI) and 42-230-141-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 201kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
-
Product
AC Power Sources, Frequency Converter
MAC-01, -02, -03
-
For reliability, all models of the Titan AC Power Sources/Frequency Converters are fully current limit protected against either continuous or transient short circuit or overload conditions. When an overcurrent condition exists, the internal current control loop overrides the voltage control loop and scales back the sinewave drive until it sees a safe output current level.
-
Product
HIGH VOLTAGE MEGOHMMETER
MI-15KVe
-
The MI-15KVe High-Voltage Megohmmeter is a truly portable device that allows the measurement of insulation resistances using test voltages up to 15 kV. It employs a state-of-the-art technology for the safe measurements of insulation resistances up to 3.000.000 MΩ with four test voltages: 1 kV - 5 kV - 10 kV and 15 kV.
-
Product
RF Voltage Probe
P-20 Series
-
The P-20A is a PASSIVE 10:1 RF VOLTAGE PROBE with a 50 Volt DC BLOCK built in. It has been designed to allow users of RF test equipment to use standard signal tracing techniques. The P-20A makes it possible to conveniently and accurately monitor or inject signals up to 3 GHz into RF circuits without significantly loading or detuning them.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-052-HI
-
The 40-230-052-HI (PXI) and 42-230-052-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4.5Ω and 5.762MΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
10 GHz Signal Source
YIG Series
-
The SC5503B and SC5502A are designed to meet demanding low phase noise applications. This is accomplished by employing a multiple phase-locked loop architecture as well as a YIG oscillator as the heart of its synthesizer. Frequency accuracy is provided by an onboard 10 MHz temperature compensated crystal oscillator (TCXO) which can be phase locked to an external reference source if required. These modules can be used as standalone CW signal sources or as LO sources for frequency conversion systems such as the SignalCore IQ modulators and demodulators. They are designed to meet the requirements of many modern applications such as wireless device testing, software-defined radio research, point-to-point radio, multi-channel coherent systems, and other academic and military programs.
-
Product
RF Reference Source
96040A Series
-
The 96040A RF Reference Source enables you to simplify your RF calibration system by replacing many of the instruments and accessories that make up your current system.
-
Product
Light Sources
-
Fiber optic light sources are a low-cost way to analyze and identify accurate fiber optic readings, while certifying optical fiber. Receive the ability to measure fiber optic light continuity, loss, and quality of the signal.
-
Product
Surge Voltage Generator
SSG 1100
-
Cable fault location with the BAUR SSG 1100. Surge voltage generators are used for pre-location and pinpointing of high- and low-resistive as well as intermittent faults in power cables. The energy stored in a high-voltage capacitor is released at regular intervals or as DC voltage. The thus generated acoustic signal at the fault position can be recorded with a ground microphone and a universal receiver.* High surge voltage up to 32 kV* Continuously adjustable voltage* Voltage monitoring through kV meters with 3 measuring ranges* Automatic discharge unit
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-225-HI
-
The 40-230-225-HI (PXI) and 42-230-225-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 3Ω and 13.6kΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Laser Sources and Amplifiers
-
We design and manufacture a range of tunable C-band and L-band telecom laser sources, customizable fixed-wavelength laser sources, broadband super luminescent (SLED) sources, swept laser sources, and Erbium-Doped Fiber Amplifiers (EDFA).
-
Product
Long Life Seismic Energy Source
1500LL
-
Excellent low frequency content. Using heavy-duty cluster spreader bars cluster elements in excess of 1,000 cubic inches possible without sacrificing peak output
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-314-HI
-
The 40-230-314-HI (PXI) and 42-230-314-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 470Ω with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 2.04k Ohm - SPST
40-294-122
-
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Light Source
LS-HA
-
provides the stable and smooth wide-band spectral output. It’s proper for most visible to near infrared range measurement. This light source is also designed to be used in the standard measurement package. It ‘s a simple and quick measurement platform.
-
Product
Light Source Measurement Products
-
Xinye Optoelectronic Engineering Co.,Ltd.
Light Source Measurement Products by Light Source Measurement Products
