Link
See Also: Camera Link
-
Product
500-Pin SEARAY Connector, Male With Backshell, 2 Amp, 250 Port
C500RMR-4SB-5C
SEARAY Male Connector
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This accessory is designed to allow users to directly terminate a cable via solder bucket connections to a PCB linked to a 500-Pin SEARAY connector. Pickering Interfaces recommend the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Science Bay Module for Gavia AUV
-
The Gavia Science Bay Module is a generic payload module that allows a Gavia user to add up to six scientific sensors to the Gavia AUV. The module includes several hull penetrations, including four (4) penetrations that can accommodate WetLabs ECO pucks, two external wet plugs that can provide power and serial communication for external devices, one slot for a SeaBird CTD, one penetration that can accommodate an Aanderaa Optode oxygen sensor, as well as a weak link on the bottom of the module. The weak link provides the option of towing an external sensor and reduces stress on the wet plug.
-
Product
GoldenGate RFIC Simulation Software
-
GoldenGate RFIC Simulation and Analysis Software is an advanced simulation and analysis solution for integrated mixed signal RFIC designs that is fully integrated into the Cadence Analog Design Environment (ADE). GoldenGate is part of Keysight's RFIC simulation, analysis and verification solution that also includes Momentum for 3-D planar electromagnetic simulation, SystemVue & Ptolemy wireless test benches for system-level verification, and the Advanced Design System (ADS) Data Display for advanced data analysis. This suite links the RF system, subsystem, and component-level design and analysis as part of a unique and comprehensive RFIC design flow.
-
Product
IP Link Pro Control Processors
-
Ethernet-enabled control processors with enhanced speed, security, and memory
-
Product
PXI 2A Multiplexer, 16-Bank, 4-Channel 2-Pole
40-614A-002
Multiplexer Module
This 16-bank, 4-channel, 2 pole version is part of the 40-614A High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.These 2A multiplexer modules are designed for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
"Signal Transporter"
LTX-5525
-
The LTX-5525 conveys sixteen independent channels of digital information over a fibre optic link ranging from metres to more than 10 kilometres. Each of the 16 incoming TTL channels is sampled 100 million times per second, multiplexed and transmitted serially over an optical fiber at two gigabits per second. The receiver acquires this digital data and de-multiplexes it to 16 separate output ports.
-
Product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 128-Channel, 1-Pole
42-614D-015
Multiplexer Module
The 40-614D-015 (PXI) and 42-614D-015 (PXIe) 1-bank, 128-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Micro-Ohmmeters
RMO-A Series
-
The RMO-A is a portable micro-ohmmeter designed for contact resistance measurements of switchgear during manufacturing, commissioning and maintenance stages. This micro-ohmmeter is widely used by medium and high-voltage circuit breakers manufacturers. Other typical applications are testing of disconnecting switches, high-current bus bar joints, cable splices, and different high-current links. It accurately measures not only in factory environments but also in high-induction fields and substationsThe RMO-A series contains 6 models, rated from 100 A (RMO100A) to 600 A (RMO600A). The RMO500A (formerly CPM500) is our best seller, with 500 A ripple-free current and weighs only 8 kg.Although placed in a very portable and lightweight metal housing, RMO-A micro-ohmmeters have very high output power capabilities. They can generate 600 A test current continuously for up to 20 s. You can test with current up to 100 A without rest time. High output voltage enables a wider measurement range at the highest test currents, as well as the use of thinner/longer test cables. For testing with 100 A, 20 m test leads can be provided with only 16 mm2 cross-section.RMO-A micro-ohmmeter generates a true DC ripple-free (less than 1 %) current with automatically regulated test ramps. During a test, the RMO-A ramps up with increasing current before measuring and decreasing current after the measurement. This significantly decreases magnetic transients and ensures great accuracy.An additional option is a built-in High Precision module suitable for measurement of very low resistances, ranges from 1 to 30 µΩ, with 0,01 µΩ resolution.These instruments can store up to 500 measurements in internal memory. A built-in thermal printer is available as an option.Our free DV Win software communicates with the RMO-A micro-ohmmeters via USB or RS232 interface. It allows you to run the test remotely from PC, as well as to download test results, analyze and generate fully configurable test reports.
-
Product
Portable Meter Test Kit
UTEC 430
-
The UTEC 430 is the first Portable Meter Test Kit to support both the Radian Dytronic (RD) and the installed base of Radian Metronic (RM) reference standards. The ability to support both reference standards makes the 430 the ideal budgetary solution for traditional on-site meter testing using Phantom Load current sourcing. Do not let its compactness fool you, the UTEC 430 has three 30 Amp current output elements for performing single-phase or three-phase meter testing. When each element is combined using the optional open link cable harness, the UTEC 430 can source up to 90 Amps.
-
Product
PXI MUX 1 Bank of 128 Channel 1 Pole
40-610-022-1/128/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
16/8 Channel 14-bit 250 MS/s Digitizer
V1725 / V1725S
-
The V1725S family comes in a VME form factor, with 16/8 input channels. The communication to and from the board is provided through the VMEBus and Optical Link interfaces.
-
Product
I2C Bus Monitor - USB
Model JI-216
-
The JI-216 I2C Bus Monitor is a low cost, easy-to-use PC hosted instrument specificallydesigned for troubleshooting and debugging I2C networks. The JI-216''s FPGA basedarchitecture provides for the capture and display of all valid or invalid messages and I2Cbus events. Captured I2C messages are available for display in two modes: real-timestreaming, or triggered. These modes provide optimized data display for either hardwareor software development. The SDA/SCL timing display aids in tracking down and solvinghardware timing problems. JI-216''s broad bandwidth (DC 3.4Mbits/s), wide input signalrange (0 15.0V), and variable signal filtering provides flexibility in monitoring a variety ofI2C bus systems. An intuitive Windows application manages instrument setup andcontrol. Communications and unit power is provided via a USB 2.0 link.
-
Product
LinkExpert Software
-
LinkExpert enables complete control and management of Teledyne LeCroy's family of Protocol Analyzer and Exerciser hardware. LinkExpert provides a convenient interface to run Compliance, Conformance and Validation tests on PCI Express (PCIe) and SAS (Serial Attached SCSI) links. The LinkExpert software interface is provided free of charge and includes as standard, several validation tests for PCIe Hosts (Root Complexes) and Devices (End Points).
-
Product
Tool and Process Monitoring
BK MIKRO
-
BK Mikro is typically used as a broken tool detection system but can also be used for many other applications such as object inspection, position recognition and checking for part defects. The selection of the scanner and controller for broken tool detection systems is mainly application based. Follow the links below to explore specific models or contact us with application questions about our broken tool detection systems.
-
Product
VME Sequencer PCI Express to VME Interface
SIS3104-2
-
The SIS3104-2 is the Artix-7 based successor to the SIS3104 board. It is backward compatible to the SIS3100/SIS3104 standard models and can be used as a drop in replacement. With two Gigabit/s link firmware transfer rates in excess of 160 MByte/s are possible im combination with the SIS1100-e2 single lane PCI Express card.
-
Product
Smart Profiling
-
The average thermal profiler on the market operates like the old chart recorder migrated onto a PC. It is a passive data acquisition unit that informs the user of the PCB profile. Smart profiling goes beyond that into the realm of data intelligence. Based on your input, the profiler tells you where you are, where you want to go, and how to get there. Intelligent databases provide such information without even needing to run a manual profile! The data can be linked and shared with all authorized personnel.
-
Product
BERT Measurement Solutions
-
Bit error rate testers (BERTs) are usually the initial step for communications testing. These instruments generate digital test patterns, typically pseudorandom binary sequences (PRBSs), that drive devices under test (DUTs). Following the transmission of the signal through the link, the receiver in the BERT captures the signal. This setup can be used for multiple testing purposes, such as to evaluate the performance of a transmitter, a receiver, or an optical link.
-
Product
Low Cost Emulator
EB-XAG49
-
* Emulates P51XG49 Microcontrollers * Real-Time Operation up to 30MHz * 3.3V or 5V Voltage Operation * Source-Level Debugger for C and Assembler * MS-Windows Debugger Software * Reduced Set of C-Compiler and Assembler * Support for ROMless and ROMed Microcontrollers * 64K of Code Memory * Performance Analyzer * Real-Time and Conditional Breakpoints * 44-pin PLCC Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115 Kbaud
-
Product
IO Expander
AD16x2DA16x8-125ETH
-
The IO Expander is an additional module to provide more input and output capabilities to the AD16x2DA16x8-125ETH. Via high speed link it connects 8 TTL inputs, 16 TTL outputs, 8 SPDT RF switches, and a GPS module.
-
Product
Radar Threat and Target Simulation Unit
MS 1605
-
PTG is used to field/LAB evaluation / testing of RADAR. PC is used to control the profile of the target generation. PTG will work in both stand alone and remote mode. The PTG has keypad and LCD for stand-alone operation. The PC can interface the PTG through the USB link. The operator can communicate through the GUI to the PTG. MIL1553B Communication used for Interfacing with RADAR.
-
Product
PXI 2A Multiplexer, 1-Bank, 4-Channel, 32-Pole
40-614C-020
Multiplexer Module
This 1-bank, 4-channel, 32 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI Express 4-Port
7404e
-
The 7404e PCI Express serial interface provides four multifunction serial ports, each individually field-configurable for RS-232, RS-422, or RS-485. Each serial port utilizes a 16C954 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is register compatible with legacy 16550 software applications. In addition, the board derives a 62.5 MHz clock from the PCI Express link. This ultra-high-speed clock is divided by a flexible 8-bit clock prescalar with 1/8 steps to provide support for the widest range of standard and non-standard baud rates.
-
Product
IO-Link
-
IO-Link is the key to taking automation solutions to the next level. Browse our IO-Link offerings to learn how to build your most powerful application yet!
-
Product
Multi Wavelength Monitor
LV5490/LV5480
-
The LV 5490 is a multi waveform monitor that supports 4K video format (4096×2160、3840×2160) based on 3G-SDI dual link or quad link, HD-SDI quad link, and 12G-SDI. The following two 4K video division transmission systems are supported. ・2-SAMPLE INTERLEAVE DIVISION ・SQUARE DIVISION
-
Product
Optomechanics
-
Welcome to Thorlabs; below you will find links to our extensive Optomechanical product line, a subset of our entire line of photonics products. Optomechanics is a broad category that includes optical tables and breadboards, optical mounts and construction components, mechanical devices with integrated electronics, kits that make it easy to buy a popular set of components or a set of components that can be assembled to perform a specific function, and general laboratory supplies and tools. Because of the large selection, Optomechanics does not include translation and rotation stages and their controllers; instead those products have their own category.
-
Product
End Point IP Core
PCIe
-
The highly configurable PCIe End point IP core supports x1, x2, and x4 lane with a selection of 32/64-bit data path. Depending on design requirements, a maximum of 8 VCs and 8 TCs are supported. The IP core consists of many useful features that can be included to enhance system performance and to address special design needs in different applications. The data link layer allows the configuration of infinite credits to boost the flow control efficiency. By-pass mode, cut-through mode, and store-and-forward mode are other optional items. The transport layer features include configurable ECRC generation and checking, support for up to 64 configurable outstanding non-posted requests, and configurable payload size from 128 to 4 Kbytes
-
Product
2U Dual Flange Kit
DAQA191A
-
Secures DAQ or DMM instruments to the front of a System II cabinet; can be used with the DAQA194A Dual Lock Link Kit
-
Product
PXI/PXIe High Density 2A Multiplexer, 2-Bank, 64-Channel, 1-Pole
40-614D-010
Multiplexer Module
The 40-614D-010 (PXI) and 42-614D-010 (PXIe) 2-bank, 64-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 22 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Fiber Optic Qualification & Dispersion Test Links
8800 Family
-
Delaire USA qualification test systems are designed to act as worst-case links for bandwidth/dispersion and attenuation, or to meet the customer's loss, dispersion, and distance requirements for custom applications. Because the test links are constructed from hand-selected, industry-standard fiber and not simulated with dispersion elements, all of the effects including loss, dispersion, and fiber nonlinearities are present and authentic. Typical applications include optical transciever testing and qualification for 40G AND 100G systems
-
Product
Satellite Interception system
-
Shoghi has designed and developed various solutions to passively intercept traffic (Voice, Fax and Data) from Global Mobile Personal Communications by Satellite (GMPCS) and point to point satellite communication networks.All solutions are fully integrated monitoring and analysis platform which enables acquisition, processing, storing and analysis of Voice, Fax, Data and High speed IP traffic.To challenge the various monitoring scenarios Shoghi has designed both tactical and strategic solutions equipped with automatic post processing, decoding demodulation and decryption of intercepted Voice, Fax, Data and High speed IP traffic.Our GMPCS Satellite monitoring solutions are capable of intercepting Voice, SMS, Fax and Data traffic along with Call Related Information and Geo-location from Thuraya-2, Thuraya-3, ISAT Phone Pro, Iridium satellite networks.The point to point satellite communication monitoring systems are capable of intercepting traffic including Voice, Fax and Data from C and Ku-band satellite carriers from Intelsat, Eutelsat, Arabsat, Turksat etc. The Satellite Monitoring system can also process and decode GSM traffic on satellite and decode high speed IP traffic online.1.Satellite Monitoring Solutions:2.Satellite Carrier Analysis System3.C/Ku Band Satellite Monitoring4.DCME Analysis System5.GSM Abis Link Monitoring Module6.IP Link over Satellite Monitoring7.Satellite Carrier Reconnaissance and Analysis System8.VSAT Monitoring System9.Satellite Terminal Geolocation System
