Visual Basic
A programming language and environment that allows rapid creation of user interfaces by dragging and dropping elements such as buttons and controls.
-
Product
Fiber Visual Fault Locator
-
Fiber visual fault locator is a pen type device which is able to locate the breakpoint, bending or cracking of the fiber glass,this small fiber optic equipment can locate the fault of OTDR dead zone and make fiber iIdentification from one end to the other end .
-
Product
Visual Inspection Software
AdVISE
-
R&S®AdVISE visual inspection software automates the process of visually monitoring an equipment under test (EUT) during a test sequence. This eliminates human inattention, ensures reproducible results and simplifies the test documentation. A typical application is EMS testing with R&S®EMC32 and R&S®ELEKTRA test software.
-
Product
Measurement, Data Analysis, Visualization, Automation
Imc STUDIO
-
With imc STUDIO, you are ready to start your measurement in a few minutes. A clearly organized channel configuration list, extensive sorting and filtering functions, numerous assistants, built-in sensor management and support of TEDS are just some of the useful functions for achieving quick, intuitive system configuration.
-
Product
BCX Basic Cyclic Corrosion Cabinet
-
Atlas Material Testing Solutions
Basic cyclic tests are used to qualify a coating or material for a specific end use on a pass-fail basis, or determine the probability of corrosion of a specific material.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Analysis and Visualization of Arbitrary Test Reports and Result Data
TEST-GUIDE
-
Test execution in development projects leads to the accumulation of various reports and data. Test automation intensifies this, producing very high numbers of test executions, which are distributed over several users and test environments. This multitude of test results from different sources can be efficiently managed and analysed using TEST-GUIDE.
-
Product
Visual Fault Locator VFL
X4007
-
X-4007 series visual fault locator is used for the measurement in single-mode or multi-mode fibers. It features a rugged design, a universal connector and an accurate measurement.
-
Product
Basic Pulsed-RF Measurements
S95025B
-
Eliminate the need for external test sets and pulse generators using the built-in pulse modulators in the PXI VNA pulsed-RF measurement solution. S95025B also controls external pulse generators and modulators and can synchronize to external master pulses. If using external master pulses or external pulse modulators, the Y1731A PXI adapter odule is recommended.
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
COM Express Type 6 Basic Module With 5th Gen Intel® Core™ I7 & 4th Intel® Core™ I7/i5/i3 & Celeron® Processor And Intel® QM87
CEM880
-
The CEM880 COM Express Type 6 basic module features 5th generation Intel® Core™ processor (H-processor line), one onboard 4 GB extended temperature DDR3L chip, and one 204-pin SO-DIMM DDR3L socket supporting up to 8 GB. With outstanding computing performance, low power consumption, wide temperature range, and seismic design, the rugged basic-size SoM (system on module) drives Internet of Things innovation and is ideal for graphics-intensive and rich I/O applications such as telecommunication, medical imaging, digital signage, gaming machines, military, and networking.
