SCR
Thyristor, Silicon Controlled Rectifier
-
-
Product
Atlas SCR Thyristor and Triac Analyser
SCR100
-
Thyristors and Triacs need special test conditions to analyse effectively - that's where the new Atlas SCR comes in. The SCR100 can apply gate test currents from 100µA up to 90mA (with test load currents of up to 100mA) so it's not limited to sensitive parts.It will automatically identify the type of part (Thyristor or Triac), identify all three leads and also categorise the gate sensitivity. This new version takes a standard Alkaline AAA battery.
-
Product
SCR CONTROLLER WITH REGULATOR
-
The SCR Controller and the Regulator Board are used in SCR controlled power supplies.CEHCO offers single phase and three phase SCR Controllers with Regulator Boards.Click the links below for additional details.
-
Product
SCR Diode Testers
-
SCRs and Diodes are used in the power sections of various power systems. A SCR Diode Tester is an important piece of equipment to determine if a SCR or a diode is defective in a power circuit. It is difficult and time-consuming to troubleshoot SCRs and Diodes with a digital meter.
-
Product
SCR CONTROLLED VARIABLE DC POWER SUPPLY
P5085C
-
Shown below is an AC to DC power supply with 4/20 ma interface. Input is 240 VAC, 1 PH, 60 Hz. Output is 0 to 10.5 DC, 130 Amps. This power supply can be interfaced to a PLC system. These units are customized units, built to order.
-
Product
HIGH VOLTAGE SCR CONTROLLED POWER SUPPLY
xPS Series
-
High Voltage SCR Controlled Power Supply, P/N 18278PS Power Rating: 350 KW. Input: 480 VAC, 3 PH, 60 Hz Output: 0 to 5000 VDC, 70 Amps max Ripple: 2 % approximately at maximum rated voltage Configuration: 12 pulse externally SCR controlled rectifier system Protection Devices: Input contactors Overload relay shutoff Input surge suppressor Thermal switches Output current limiting resistor (made with 5 Ohm Kanthal heating element) Emergency power shutoff Cooling: Each 6 pulse rectifier assembly is cooled by three 10” fans Interface: 4/20 ma converter interface for output voltage and output current to SCR controller. Enclosure: The overall dimension of the unit is (78”H x 38”W x 53”D). It is comprised of two separate enclosures each with dimensions of (78” H x 38” W x 26” D) which are integrated together to form a single enclosure. Each half enclosure has one 6 pulse transformer and one 6 pulse high voltage rectifier. Weight: Approx. 5000 lbs. SCR Controller: The 12 pulse SCR controller is supplied by the customer. We were responsible for the 12 pulses Transformer and 12 pulses Rectifier section. Portability: Unit can be lifted up with a fork lift. It can also be moved around with a 5000 lb pallet jack. Transformer: Two 200 KVA transformers are used to step 480 VAC to 3750 VAC each in a 12 pulse configuration Rectifiers: Two 6 pulse rectifier assemblies capable for 5000 VDC and 60 Amps output were used. The high voltage rectifier assemblies are isolated and protected in a fiberglass plenum within the enclosure. Blocking Diode: Each diode of the 6 pulse rectifier consists of 10 diodes in series to offer a blocking voltage of 12000 V (PIV)
-
Product
Surge Suppressor to Suppress SCR Spikes from Customer Equipment Going Back to Utility Power, P/N 5965C
-
This Suppressor Board is ideal for SCR Controlled Power Supplies when SCR control is on the primary side.The Suppressor Board will prevent SCR spikes to go back into the 480 VAC utility power lines.
-
Product
SCR CONTROLLED DC POWER SUPPLY
74239
-
CEHCO P/N 74239Power Rating: 60 KWInput: 480 VAC, 3 PH, 60 HZOutput: 0 to 240 VDC, 250 Amp MaxSCR Controlled Power SupplyContactor, Start/Stop Control, Thermal Protection includedVoltage and current adjust availableFull operation and maintenance provided
-
Product
SCR Controlled DC power Supplies
-
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with an SCR controller. The AC input power can be single-phase or three phases. With single-phase AC input, the DC output ripple is very high (50%). With three-phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three-phase AC input instead of a single phase.
-
Product
SCR Rectifiers
-
SCR-controlled rectifiers are electronically controlled via analog signals for constant voltage and current control. The compact and service-friendly design complies with high industrial requirements and guarantees excellent operational reliability.The input voltage can be from 208 VAC to 600 VAC, 3 PH, 50/60 Hz. Maximum output voltage can be from 6 VDC to 600 VDC. Maximum output can be from 1000 Amps to 100000 Amps. These units can be air cooled, water cooled or oil cooled.
-
Product
High Voltage Inclined Plane And Erosion Tester
-
SCR ELEKTRONIKS have developed HIGH VOLTAGE INCLINED PLANE AND EROSION TESTER to carryout test specified in many standard to cover test method for the evaluation of the relative tracking and erosion resistance of insulating solid using liquid contaminant (ASTM D2303). Perform the Initial Tracking Voltage Test, Time to track Test, And Erosion Test as per selection.
-
Product
MOTORIZED VARIABLE TRANSFORMER CONTROLLED POWER SUPPLY
-
Motorized Variable Transformer Controlled Power Supply, P/N 18534PSInput: 460 VAC, 3 PH, 60 HzOutput: 0 to 250 VDC, 200 Amp max.Variable Transformer is used to vary the output. SCR controller is not used, as it generates harmonics.Input control is 0 to 3.6 VDC.Indoor enclosure.Output voltage and current feedback as 4/20 mA for PLC interface.All input/output connections are inside the enclosure
-
Product
Replacement Selenium Surge Suppressor Specialists
-
Surge suppressors are used to protecting circuits from transients (sudden, brief increases in voltage). Transients of widely varying magnitudes are caused by such circuit components as motors, coils, magnets, relays, and transformers. They are found in all electrical systems and are notorious for damaging diodes, SCRs, transformers, triacs, and relay contacts.
-
Product
Bridge Rectifier Assemblies
-
Bridge Rectifier Assemblies are constructed by packaging diodes and/or SCR components with heat sink extrusions in a bridge circuit.CEHCO uses M, T, N and W heat sink extrusions to build rectifier assemblies.
-
Product
DEF Refractometer - Urea Scale
DEF-201
-
The MISCO DEF-201 digital refractometer is the ideal method for testing and monitoring the concentration of urea-based Diesel Exhaust Fluid (DEF or AdBlue) required by diesel engines equipped with Selective Catalytic Reduction (SCR) technology. This refractometer has a single scale for DEF concentration.
-
Product
Programmable Parametric Tester For Discrete Semiconductors
IST-8800
-
IST Information Scan Technology, Inc.
The IST-8800 is a fully programmable, low cost tester that provides parameter measurements or parametric GO/NO GO test for transistors, diodes, MOS-FETs, Regulators, Triacs, Zeners, SCRs, and J-FETs. These devices can be tested up to 5 amps or 1200 volts with a measurement range down to the nano amp range. Only four universal test fixtures are required which can test the device across a wide range of packages.
-
Product
Commutator Testing Unit
-
SCR ELEKTRONIKS have designed “Commutator Testing Setup” to provide Commutator manufacturers and users a simple and speedy method for testing their Commutators. This single station commutator testing set up therefore user can test one commutator at a time. In Automatic mode of testing this set up performs two tests automatically.
-
Product
Test Finger Apparatus
-
SCR ELEKTRONIKS focuses on designing a solution around the end use at her customer. Instead of offering a standard instrument for a specific task, we have an approach of customizing the test bench to target the specific goals of the process or test procedure. Our measurement instruments, test modules, electrical power systems & software libraries are developed with this vision, thereby reducing the test system’s time-to-deploy.
-
Product
MCB Temperature Rise and Power Loss Test Bench
-
The SCR Elektroniks 3 station MCB Temperature Rise and Power Loss Test Bench is economically designed to verify temperature rise and measure power loss as per clause 9.8 of IEC 60898 with the circuit designed to follow test procedure as per Cl 9.8.2. The temperature rise is measured in accordance with Cl 9.8.3 and 9.8.4 while power loss is measured and verified as per Table 15 of Cl 9.8.5.
-
Product
Power Discrete Tester
Mostrak-2
-
M2 test system has multiple test generators which cover static and dynamic test procedures. It is our first truly modular tester which allows for the system to be upgraded and expanded when needed. M2 are designed to get the tester as close as possible to the handler interface and operator at the highest possible speeds. M2 is capable of HV (3 kV) and LV (600A) testing and has dynamic switching capabilities up to 1200V. MOSTRAK systems can test the following device types: MOSFET, IGBT, Bipolar transistor, Diode - rectifiers, Thyristor (SCR) - Triac, Linear voltage regulator (VReg), Transient voltage suppressor (TVS).
-
Product
Test Bench For Circuit Breaker
-
SCR ELEKTRONIKS have developed Test Bench for Circuit Breaker to test 2, 5 & 10 at a time. Panel is provided with constant DC current source.
-
Product
Preheating Test Setup for Hair Straightener
-
SCR ELEKTRONIKS have developed "60 Stations Preheating Test Setup for Hair Straightener“ for Testing of Hair Straightener. It consists of Adjustable Constant Voltage source, Digital Timer, Digital Voltmeter, Digital Timer for carrying out Heating Test of Hair Straightener. It has got the capacity to check hair straightener that require test current 28 A at different Test Voltages.
-
Product
Thermal Characterization Testing Services
-
Thermal Engineering Associates, Inc.
Thermal Characterization - TEA offers this service to customers having need for precise thermal parameter values for product data sheets, purchase specifications, specific application configurations, and/or device comparisons. This service is offered for a wide range of Discrete Devices (i.e., Bipolar Junction Transistors, MOSFETs, IGBTs, Diodes, SCRs, Triacs) and Integrated Circuits (i.e., digital, linear and mixed-signal devices).
-
Product
Earth Contact Resistance Tester
-
SCR ELEKTRONIKS have developed an equipment namely Earth Contact Resistance Tester to test the appliance. To ensure the safety of operator it is essential that the Earth path (connection) should offer minimum impedance to by pass short circuit Current to Earth. This is ensured by measuring Resistance of the Earth path by passing heavy Current say 25 A. The Earth Contact Resistance Tester essentially comprises of a Variable Current source with digital Ammeter to measure the Current supplied. The Voltage drop across the Earth path is measured with a digital Voltmeter. Optionally for a particular Current (25 A) the meter can be calibrated in terms of Resistance. A timer is provided to switch off the Current after the Set Time.
-
Product
MCB Tripping Current Characteristic Test Bench
-
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
Product
Rebuilt Testers
-
Lorlin® manufacturers New and Rebuilt Discrete Component Semiconductor Test Systems for Transistors, Diodes, Zeners, Fets, IGBTs, SCRs, Triacs, Optos, Small Signal and Power Semiconductors. We measure, screen, test, analyze, characterize and sort the critical parameters of semiconductors devices including Leakage Current, Breakdown Voltage, Gain, Saturation Voltages, and offer a comprehensive test parameter library with an easy to use Windows based applications software. The systems us a Windows 10® 64-BIT Operating System with a USB 2.0 Interface. Engineering excellence, innovation, creativity and cutting edge technology has made Lorlin equipment well known for testing discrete components.
-
Product
Temperature Rise Test Panel
2000A
-
SCR ELEKTRONIKS have developed “TEMPERATURE RISE TEST BENCH FOR MEDIUM VOLTAGE SWITCH BOARDS” to measure rise in temperature at various points as mentioned in standard at junctions. The set-up consists of a True RMS Constant Current Source (to maintain the Current within + / - 1 % of set value with Digital Indication), PC based control system, Temperature data logging on PC, Servo-Controller and other indications. Digital voltmeter Primary Voltage) indicates the position of auto transformer (variac).
-
Product
MOTORIZED TRANSFORMER/RECTIFIER ASSEMBLY, 0-250 VDC, 200 A OUTPUT
18534PS1
-
Input power is 380 VAC, 3 PH, 50 Hz, P/N 18534PS1Output is 0 to 250 VDC, 200 Amp max.Variable Transformer is used to vary the output. SCR controller is not used, as it generates harmonics.Input control is 0 to 3.6 VDCIndoor enclosure, 50"H x 46"W x 36"DOutput voltage and current feedback as 4/20 mA for PLC interface.All input/output connections are inside the enclosure
-
Product
High Voltage Power Supplies
-
High voltage SCR controlled power supplies require the following:Output voltage is high. Output current is generally Low.Voltmeter and ammeter display the output voltage and current under load.Potentiometers are used to adjust output voltage and limit output current from minimum to maximum.
-
Product
SCR CONTROLLED DC POWER SUPPLY
PS Series
-
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with an SCR controller. The AC input power can be single phase or three phases. With single phase AC input, the DC output ripple is very high (50%). With three phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three phase AC input instead of single phase.
