Multiplexers
Combine multiple signals into one signal.
See Also: Switching, Switching Matrix, High Voltage Switching, Switching Matrices, General Purpose Switch
-
Product
Multiplexers
-
K&L Microwave provides triplexers, quadriplexers, and multiplexers built to customers' electrical, mechanical, and environmental specifications. The list below contains part numbers meeting existing industry and customer specifications. Use the quote cart to request a quote on a specific design or to provide specifications for a custom design.
-
Product
Precision Low-Loss Multiplexers
-
Maury’s line of diplexers (DP-series) and triplexers (TP-series) are designed for applications which require combining/ splitting signals at or around harmonic frequencies (nFo) and are connectorized for design-in and test and measurement applications.DP-series diplexers are designed using low-pass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.TP-series triplexers are designed using low-pass, bandpass and high-pass filters and pass bias between the low-frequency (or Fo) port and the common (or DUT) port.Power handling is rated at 100W CW (average) and typical insertion loss is better than 0.5dB between the low-pass (Fo) and common ports.DP- and TP-series multiplexers are ideal accessories for passive, active and hybrid-active multi-harmonic load pull systems.
-
-
Product
Diplexers, Triplexers, Multiplexers & Combiners
-
LBA Technology custom engineered diplexers, triplexers, and multiplexers provide broadcast ers the ability to transmit two or three different AM signals for one series-fed antenna.
-
Product
Hand Multiplexers
MTM
-
The manual torque multiplier is a low cost solution that's ideal for wheel nuts and remote locations where air and electricity aren’t easily accessible. The gearing design allows for a high torque output with minimal input. Commonly used in petrochemical, power generation, transportation, shipping and maintenance industries.
-
Product
Multiplexers
-
The range extends from Lumped Element Diplexers at 300 MHz through to 60 GHz devices based on BSC’s Exact Filter Technology. Our design experience and in-house production facilities have allowed us to construct Diplexers with near contiguous passbands meeting the most demanding technical requirements.
-
Product
High Performance LXI RF & Microwave Multiplexers
Microwave Multiplexer
Our standard microwave multiplexers offer the highest density configurations available, packaging up to 16 SPnT switches into a 2U high rack-mount enclosure. Standard microwave multiplexer systems include 50Ω Versions up to 67 GHz and 75ΩVersions up to 2.5 GHz. Alternatively, you can use our Microwave Switch Design Tool to mount any combination of our wide range of transfer and SPnT relays onto your own front panel design.
-
Product
Hand Multiplexers
HG
-
HG hand torque multipliers are the ideal tools for applications where air and electricity aren't easily accessible. The gearing design allows for a high torque output with minimal input. Commonly used in petrochemical, power generation, transportation, shipping and maintenance industries.
-
Product
LXI Video RF Multiplexers
RF Multiplexer
Pickering's LXI Video RF multiplexers, high performance MUXs suitable for video switching applications designed for the switching of RF signals in 75 systems at frequencies up to 1GHz. These multiplexers are also ideal for 75 monitoring applications that require a multiplexer to select one channel to be routed to measuring equipment.
-
-
Product
Filters and Multiplexers
-
CAES offers an extensive line of RF filters and multiplexers designed and manufactured using our internal capabilities in machining and component and substrate fabrication.These heritage processes have proven flight pedigree in space, on board Gen 5 aircraft and shipboard platforms. CAES' proprietary plating processes enables industry leading high-Q, low l
-
Product
Multiplexers (MUX)
WDM
-
It is highly desirable to reduce the number of cables required to communicate between spaces on Navy ships due to increased weight, cost and maintenance concerns. To reduce weight and expense, copper-based NTDS parallel and serial type cables can be converted to fiber optic and multiplexed using Wavelength Division Multiplexing (WDM) technology. WDM technology allows for multiple fiber optic wavelengths to be combined in a single fiber and then separated back to individual fibers at the distant end. Using Coarse WDM (CWDM) which utilizes wavelengths 20nm apart ranging from 1271 nm to 1611 nm, provides for up to 18 optical wavelengths to be combined into a single fiber. Optionally Dense WDM (DWDM) can be used allowing for up to 160 optical wavelengths.
-
Product
Digital Fiber Multiplexers & Wavelength Shifters
FiberSaver Series
-
We don’t always have unlimited amounts of fiber at our disposal. Whether working in pre-fibered event venues, houses of worship or moving camera signals across busy metropolitan areas, fiber counts can quickly add up – especially when bi-directional optical transmission is required. MultiDyne’s FiberSaver Series is built for the system designer who needs a robust yet compact solution for signal links where fiber strands are limited, or where fiber feed requirements exceed budgets. FiberSaver products help technicians send and receive more optical signals over fewer fibers. Wavelength-agnostic inputs will multiplex just about any digital optical coming from SMPTE cameras, Network Switches, etc., and combine them with several optical matrix inputs. Scalable in increments of six channels, content producers now have a cost-effective solution to carry extra signals for sports production, distance learning and remote broadcasting.
-
Product
USB Data Communications Multiplexers
-
These USB multiplexers are ideal for the testing of multiple devices that use USB interfaces, allowing the test system to select one target device from many. The design is bi-directional to permit use as a multiplexer or de-multiplexer with no impact on performance and uses long lifetime electro-mechanical relays characterized for use in data communications systems.
-
Product
High Performance LXI Microwave Multiplexers
Microwave Multiplexer
Pickering's LXI Microwave Multiplexers offer the highest density microwave multiplexer configurations possible, packaging 16 multiplexers into a 2U high rack. All versions of this multiplexer have an extremely high level of performance, offering low VSWR, high isolation, low loss and high power handling. Occupying only 2U of valuable rack space - our microwave multiplexers provide a space saving solution for systems requiring high performance multiplexers in the construction of microwave switching systems.
-
Product
PCI Very High Density Multiplexer, 99-Channel, 1-Pole
50-670C-021-99/1
Multiplexer Module
The 50-670C-021-99/1 is a 99-channel,1-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 18GHz, 50Ω, SMA
40-785C-422
Multiplexer Module
The 40-785C-422 (PXI) and 42-785C-422 (PXIe) are dual SP4T 18GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI-2797, 40 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module
782357-01
RF Multiplexer
40 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module—The PXI‑2797 offers a high-density, terminated multiplexer with dual 6x1 multiplexer banks in the same module. The internal termination of the PXI‑2797 helps prevent high-power reflections that arise from open channels on the module. It is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules.
-
Product
PXI 2 Amp Multiplexer, Quad 8-Channel, 1-Pole
40-635A-108
Multiplexer Module
The 40-635A-108 is a quad 8-channel, 1-pole MUX and is part of a range of Multiplexer modules available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
Product
PXI/PXIe High Density 2A Multiplexer, 10-Bank, 4-Channel, 3-Pole
42-614D-022
Multiplexer Module
The 40-614D-022 (PXI) and 42-614D-022 (PXIe) 10-bank, 4-channel, 3-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above).
-
Product
16 Channel Multiplexer (2/4-wire) Module for 34970A/34972A
34902A
Multiplexer Module
The Keysight 34902A module for the 34970A/34972A Data Acquisition/Switch Unit employs reed relays to achieve scan rates up to 250 channels-per-second. Use this module for high-throughput automated test applications as well as high-speed data logging and monitoring tasks.
-
Product
PXI/PXIe MEMS Optical MUX, Single 2-Channel, Single-Mode
40-855A-012
Multiplexer Module
The 40/42-855A-012 is a PXI/PXIe 2-channel multiplexer with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
LXI Microwave Multiplexer, SP4T, 6-Bank, 26.5GHz, 50Ω, SMA
60-803-306
Multiplexer Module
Our 60-803-306 is a 6 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI 16:1 Optical MUX SC Loop-Thru
60-851-223
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
Product
PXI Quad 4 to 1 RF Multiplexer 3GHz 50 Ohm MCX Terminated
40-876-104
Multiplexer Module
The 40-876-104 is a 50 Ohm 4 to 1 RF multiplexer with 4 banks in a single PXI slot. Additionally, extra switching allows the common connection to be terminated into 50 Ohm, maintaining signal integrity. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
PXI/PXIe High Density 2A Multiplexer, 4-Bank, 8-Channel, 4-Pole
42-614D-008
Multiplexer Module
The 40-614D-008 (PXI) and 42-614D-008 (PXIe) 4-bank, 8-channel, 4-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI 20 Banks of 4 Channel 2 Pole MUX
40-615-022-20/4/2
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 50GHz, 50Ω, SMA-2.4
40-785C-552-E
Multiplexer Module
The 40-785C-552-E (PXI) and 42-785C-552-E (PXIe) are dual SP6T 50GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
LXI Microwave Multiplexer, SP6T, 12-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-512
Microwave Multiplexer
Our 60-800-512 is a 12 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber
40-852A-118-HI
Multiplexer Module
The 40/42-852A-118-HI is a PXI/PXIe 8-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
