PCI Express
Serial architecture local bus with each lane running at 2.5 Gigabits/sec speeding communication between CPU and graphics controller. Also known as: PCIe
See Also: Serial, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, Serial ATA, Serial Peripheral Interface, SMBus, PCI Express Test, PCI Express Analyzers, PCIe
-
Product
PCIe 16 Bit Arbitrary Waveform Generator - 40 MS/s on 2 Channels
M2P.6541-X4
Arbitrary Waveform Generator
The M2p.65xx series offers different versions of arbitrary waveform generators for PCI Express with a maximum output rate of 125 MS/s. These boards allow to generate freely definable waveforms on several channels synchronously. With one of the synchronization options the setup of synchronous multi channel systems is possible as well as the combination of arbitrary waveform generator with digitizers of the M2p product family. The 512 MSample on-board memory can be used as arbitrary waveform storage or as a FIFO buffer continuously stream data via the PCIe interface. Importantly, the high-resolution 16-bit DACs deliver four times the resolution than AWGs using older 14-bit technology.
-
Product
PCIe Cable: x8, 2.0 m
Y1202A
PCIe Cable
Use to connect a PXIe or AXIe chassis to a desktop or rackmount computer.
-
Product
PCI Express Control of PXI/CompactPCI
PCIe-8560/PXI-8565
-
The PCI Express-to-PXI/CompactPCI expansion kit provides control of PXI/CompactPCI modules installed in a PXI/CompactPCI expansion system using the high-bandwidth PCI Express technology. With comprehensive hardware and software transparency, the expansion kit enables fast and convenient detection of any installed PXI/CompactPCI cards in the expansion system, without requiring additional drivers or software installation. The PCIe-8560 and PXI-8565 are connected by a shielded twisted copper cable of up to seven meters for remote operating convenience. Suitable for remote industrial control or automation, the PCI Express-to- PXI/CompactPCI expansion kit is designed to withstand rugged environments and harsh operating conditions.
-
Product
PCI Express 5.0 Protocol Exerciser/Analyzer
Summit Z58
Analyzer
The Summit Z58 is a PCIe 5.0 protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z58 can emulate PCI Express 5.0 root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
Product
Intel® Celeron J1900 & Atom E3825/E3845, 3.5" MI/O-Compact SBC, DDR3L, VGA, HDMI/DP, 48-Bit LVDS/eDP, 2GbE, Mini PCIe, MSATA, IManager, MIOe
MIO-5251
Single Board Computer
Intel® Celeron J1900 & Atom™ E3825/E3845, DDR3L-1066/1333MHz SODIMM up to 8GBDirectX11, OpenGL3.2, OpenCL1.2, multi-display: VGA+LVDS/eDP+ HDMI/ DP*Flexible design using integrated multiple I/O: MIOe to approach vertical applications & keep domain knowhow2 Intel i210 GbE, rich I/O: 4COM, SATA, USB3.0, SMBus/I2C, GPIO full-size Mini PCIe w/ SIM holder, full-size mSATASupports iManager, SUSI APIs, WISE-DeviceOn and Edge AI Suite
-
Product
Desktop Network Appliance Platform With Intel® Celeron® Processor J1900 And 4 LAN
NA342
-
The NA-342 is compact network hardware platform for VPN, Firewall, UTM and other network security applications. It supports low power Intel® Celeron® J1900 processor and up to 8GB of DDR3L memory. In addition, the NA-342 features one internal 2.5" HDD for storing event log and a Mini PCIe for wireless card installation. The NA342 has an optional feature to support LAN bypass function through WDT and GPIO pin definitions to prevent sudden shutdown.
-
Product
PCI Express card carrier, PCIe Gen 3 x8 connection
SA4-COUNTRY
-
The SA4-COUNTRY is a peripheral slot board for PICMG® CompactPCI® Serial systems and acts as carrier for low profile PCI Express® Card. The SA4-COUNTRY is provided with a PCI Express® x8 connector.
-
Product
Multichannel, High-Speed Data Converter
Model 71862
-
The 71862 is a multichannel, high-speed data converter with programmable DDCs (digital downconverters). It is suitable forconnection to HF or IF ports of a communications or radar system. Its built-in data capture feature offers an ideal turnkey solution as well as a platform for developing and deploying custom FPGA-processing IP. XMC (VITA 42) with PCIe Gen 3 interface.
-
Product
2U 20" Short-Depth Edge Server
HPC-6240+ASMB-622V3
-
2U 20" short-depth edge server with a 5th/4th Gen Intel® Xeon® CPU, 4TB DDR5, and 8 PCIe Gen5 slots. Built for high-density AI and edge data centers.
-
Product
cPCI Serial 4U 84HP 9 Slots
Chassis
As the established PICMG 2.0 CompactPCI has evolved, so has Hartmann Electronic’s product line. The 4U cPCI 9 slot solution is designed with quality and versatility in mind. This chassis comes complete with a 3U, 9 slot PCIe Gen3 backplane with single star topology, powered by two 300W cPCI Serial power supplies.
-
Product
PCIe 2.0 Test Platform
PXP-100B
Test Platform
The Teledyne LeCroy PXP-100B Test Platform provides a convenient means for testing PCIe 2.0 add-in cards with a self-contained portable and powered passive backplane. The PXP-100B provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer. As an alternative to an interposer, the PXP-100B includes two mid-bus probe footprints to allow connection to an analyzer via a mid-bus probe.
-
Product
Full 4-Axis Motion Control Universal PCI Express Card
PCIE-1245
-
Encoder input: 5 MHz for CW/CCW,P/D,AB mode; Pulse output: up to 5 MHzSupports memory buffer (10 K points) for trajectory planningSupports point-to-point, line and E-Gear; Supports hardware emergency inputCircular and helical interpolation (PCIE-1245 only)Position latch up to 10KHz and memory buffer 1K points (PCIE-1245 only)Position compare triggering up to 100 KHz, and memory buffer is up to 100 K points (PCIE-1245 only)1D&2D plane position compensation (PCIE-1245 only)Gantry mode by semi-closed loop pulse train control (PCIE-1245 only)Dynamic PWM output for velocity following (PCIE-1245 only)
-
Product
Pico-ITX SBC With Intel® Pentium® Processor N4200 & Celeron® Processor N3350, HDMI/LVDS And LAN
PICO312
-
The PICO312 is a palm-sized fanless pico-ITX motherboard built with the latest 14 nm Intel® Pentium® processor N4200 or Celeron® processor N3350 (codename: Apollo Lake SoC). One 204-pin DDR3L-1867 SO-DIMM socket supports system memory up to 8GB. The tiny 2.5” pico-ITX embedded board features Intel® Gen9 graphics engine bringing a true high definition visual experience with dual display configurations through one LVDS and HDMI. In addition, it was designed for special needs of fanless operation under temperature from -20°C to +70°C. The PICO312 features a full-sized PCI Express Mini Card slot in support of mSATA and a pair of expansion connectors with additional signals including one PCIe x1 lane, one LPC, one DDI, four USB 3.0 ports, one SMBus and one HD audio, giving this SBC high expandability to meet all requirements.
-
Product
1-Port Gigabit Ethernet, Intel® I225, 2.5Gb/s, IEEE 1588, TSN, 1x RJ45, B+M Key (3042, PCIex1)
PCM-34R1TP
-
Meets Advantech iDoor technology standardSingle 2.5GbE LAN Port (RJ45)M.2 3042 B+M Key compliant (PCI Express)PCIe Gen2 x1 bandwidth specificationSupports Time Sensitive Network (TSN) (IEEE 1588) and PXECompatible with embedded automation PC UNO-1/2/3/4 seriesCompliant with FCC/CE Class A CertificationOperation temperature 0~60 degree support
-
Product
Octal Serial FPDP Interface with Virtex-6 FPGA - 6U VPX
Model 58611
-
- Four or eight channels of serial FPDP interface- Fully compliant with VITA 17.1 specification- Fiber optic or copper serial interfaces- One or two Virtex-6 FPGAs- Up to 2 or 4 GB of DDR3 SDRAM- PCI Express interface up to x8- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available
-
Product
mSATA SSD Carrier
SD3-GLISS
-
SD3-GLISS fits into any CompactPCI® Serial peripheral slot that is PCIe enabled. Hardware RAID operation is supported, running with an enhanced ARM-based processor to offload the host CPU.
-
Product
PCIe® Gen5 NVMe SBExpress Test System
SBExpress-RM5
-
The SANBlaze SBExpress-RM5 is a complete turnkey PCIe® Gen5 NVMe SSD Drive validation test system. The SBExpress-RM5 feature set provides unique functions applicable to all aspects of a product lifecycle, from development and QA, to design validation and manufacturing test cycles. The ability to drive Gen5 NVMe SSDs with a wide range of configurable attributes provides engineers with a flexible, multi-controller supported validation test platform. Development, qualification, and certification test cycles can be highly automated, thus reducing overall test time, and rapidly surfacing errors and non-conformance.The SANBlaze SBExpress-RM5 hardware provides a rackmount chassis with sixteen dual or single port front-accessible drives.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 2 Channels (Single Ended) or 2 Channels (Differential)
M2P.5961-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Intel® Pentium N4200/Celeron N3350/ Atom™ E3900 Series Pico-ITX SBC
MIO-2360
Single Board Computer
Embedded Intel® Pentium N4200/Celeron N3350/Atom™ E3900 seriesDDR3L 1866MHz support up to 8BGDual display: 24-bit LVDS+VGA/HDMIFlexible design using integrated multiple I/O: MIOe to approach vertical applications & keep domain knowhow2 COM, 1 SATA, USB3.0, PCIe Mini Card and mSATASupports iManager, SUSI APIs, WISE-DeviceOn and Edge AI Suite
-
Product
14-Bit PCI Express Digitizer
SIS1160-SFMC01
-
The SIS1160-SFMC01 is the combination of the SIS1160 carrier with the SFMC01 2 channel 2.5 GSPS 14-bit digitizer FMC.
-
Product
TeleScan PE Software
-
The powerful display allows users to group the devices in a simple device tree, Device/Port/Type, or Bus/Device/Function numbers. All register field descriptions are displayed by selecting the individual fields. Each register value in a single PCIe component's register can be read and if writable can be modified. The user can decode and change each bit value of any register on the fly using the built-in the PCIe specification display referenced for all registers. The extended register for M-PCIe is also decoded and displayed for devices supporting that specification. The PCIe/NVMe configuration space info on one system can be saved and later compared to a different system by loading a saved configuration onto a second system. Searching is available for locating PCIe devices. Other features include Auto Scan, Configuration Space View, Specification decoding for standard registers. The utility supports scanning on host machines using Microsoft Windows 7, 8, 10 and on Linux systems.
-
Product
Serial Interface Device
Serial Interface
The Serial Interface Device offers a number of options for connecting to serial hardware. You can choose from Ethernet, USB, PCI, PCIe, or ExpressCard interfaces to add up to 16 serial ports to your system. You can choose from common serial protocols, such as RS232, RS422, and RS485. The Serial Interface Device also offers various isolation, hyperthreading, and multiprocessor compatibility options. Some models also support 4- and 2-wire transceiver modes for full- and half-duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Highly Scalable Gaming Platform Based On 12th Gen Intel® Core™ Processors Supports Up To Eight Independent Displays Including 4K UHD
ADi-SA3X-AD
Gaming Platform
ADLINK‘s ADi-SA3X-AD all-in-one gaming platform features powerful processing and graphics performance for gaming and retail. Equipped with 12th Generation Intel® Core™ processors, the ADi-SA3X-AD provides compelling graphics performance from a PCI Express 3.0x16 discrete graphics card and/or an embedded Intel® Iris® Xe supporting up to eight independent monitors.
-
Product
3-Channel 200 MHz A/D and 2-Channel 800 MHz D/A with Virtex-7 FPGA - 3U VPX
Model 52720
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three 200 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1 and 2) interface up to x4- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
MTCA.3 Conduction Cooled MicroTCA Carrier Hub (MCH)
UTC041
-
The VadaTech UTC041 is the most feature-rich conduction cooled MicroTCA Carrier Hub (MCH) on the market. Its management software is based on VadaTech’s robust Carrier Manager and Shelf Manager which have been deployed for years with proven results. The MCMC manages the Power Modules, Cooling Units, and up to 12 AMCs within the chassis. It also manages PCIe Gen3 or 10GbE XAUI fabric switch as well as the standard GbE with 10GbE uplink Base Channel switch.
-
Product
4K HEVC Broadcast Video Encoding Card
VEGA-3311
-
a high-performance, hardware-based PCI Express or openGear module designed for real-time compression of 4K UHD video (up to 60fps) using the H.265 standard.
-
Product
PCIe FPGA Carrier For FMC, Virtex-7
PCI516
-
The PCI516 is based on the Xilinx Virtex-7 690T, which provides 3,600 DSP slices, 52,920 Kb RAM and 690,000 logic cells. The FPGA interfaces directly to the FMC DP 0-9 and all FMC LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR3 memory channels (64-bit wide and 16-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10 G/40 G, SRIO, PCIe) without the need to go through the host.
-
Product
CoalXPress Frame Grabber
Xtium-CXP PX8
-
The Xtium™-CXP is based on the industry standard PCI Express™ Gen 2.0 expansion bus to deliver high speed access to host memory. The Xtium series offers high performance frame grabbers for CameraLink, CameraLink HS and CoaXPress interface standards. The Xtium Series takes full advantage of PCIe Gen 2.0 platform to deliver bandwidth up to 3.4 GB/s using PCIe x8 slots. By enabling maximum sustained throughput and ready-to-use image data, the Xtium series minimizes CPU usage and improves processing times for the host applications. In addition, the Xtium series offers enhanced memory architecture to handle area and line scan, monochrome and color cameras. In addition, the Xtium-CXP series support image acquisition rate of up to 6.25 Gb/s from four input channels.
-
Product
MiniPCI Express to M.2 PCIe (2) Adapter (E-key)
SKU-089-11
-
MiniPCI Express has M.2 (E-key) connector. It allows connection M.2 modules with M.2 (E key) or (A-E key) to a MiniPCI Express circuit. Adapter can be installed in Full size or Half size MiniPCI Express circuits and this Adapter supports PCI express (slot 2) and USB 2.0 interfaces.
-
Product
SQFlash ER-1 U.2 2.5" SSD (SFF-8639) PCIe/NVMe Gen.4 X4, Edge Grade
SQF-CU2 ER-1
Solid-State Drive
U.2 (SFF-8639) PCIe/NVMe 2.5" SSD, Compliant with PCIe Gen. 4 x 4 interface and NVMe 1.4, AES-256 Support & TCG-OPAL Compliant. Support LDPC with RAID ECC, Read-Intensive and Mixed-Use support. Heat-spreading design with thermal solution, SMART and GUI management tool.
