Filter Results By:
Products
Applications
Manufacturers
Tuners
Adjusts a signals frequency to one frequency or band of frequencies.
-
product
Antenna Tuner
DU-3000T/DU-3000TB
The DU 3000T and DU3000TB tuners optimize the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching. The DU-3000 series also measure the Power and Standing Wave Ratio (SWR), which allows you to tune the indicated SWR to the lowest possible value for the selected transmitfrequency.
-
product
Automatic Antenna Tuner
Automatic Antenna Tuner has not been released for full Beta testing and production yet as we are solving some firmware issues. We cannot give you a date nor estimate at this time when full production will commence.
-
product
Antenna Tuners
DU-3000T / DU-3000TB
The DU 3000T and DU3000TB tuners optimize the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching. The DU 3000 series also measure the Power and Standing Wave Ratio (SWR), which allows you to tune the indicated SWR to the lowest possible value for the selected transmitfrequency.
-
product
Antenna Tuner
DU-1500L
Model DU 1500 L is high power antenna tuner that uses and adjustable reactive network for matching the unbalanced 50 ohm output impedance of transmitters and transceivers to a variety of balanced and unbalanced loads.It is usable over a frequency range of 1.8-30 MHz. Provision is made for selecting one of three antennas or for bypassing the matching network.A crossed needles SWR and wattmeter with switchable 200 and 2000 watt scales and selectable peak and average power output reading is included.
-
product
Modulator
SFT3348T
Hangzhou Softel Optic Co., Ltd.
SFT3348T is a high performance and cost-effective DVB-T modulator designed by Softel. It has 8 DVB-S2 tuner inputs, after multiplexing, scrambling and modulating process, then it gives 4 RF output. To meet customers’ various requirements, this device is also equipped with 128 IP input and 4 MPTS output over UDP and RTP. Its pluggable structure design greatly facilitates the change of modules as needed. Moreover, the four CAMs/CIs accompanied can descramble the programs input from 8 Tuner inputs. SFT3348T can be upgraded and controlled through network system, which allows it to be widely used in setting up digital broadcasting network and provide good signals for scientific laboratory and DVB-T STB.
-
product
FTTH Optical Node
SFT3908
Hangzhou Softel Optic Co., Ltd.
- Support 8 tuners (DVB-S/S2/S2X) input; 1 U chassis optional for 1/2/3 cards maximum for 8/16/24 tunerinput; Each tuner card are working independently with its NMS and 1 GE Data port - 8 MPTS (8MPTS out thru bypassing) under Passthrough mode over UDP/RTP thru Data port,unicast/multicast-Version 1 -2 MPTS out after multiplexing or 512 SPTS out switchable under Mux mode over UDP/RTP thru Data port, unicast/multicast-Version 2-Up to 256 PIDs remapping per output channel(Mux mode only) - Support PID re-mapping and pass-through(Mux mode only) - Support Diseqc function(Mux mode only) - Support Biss decryption, each tuner support maximum 64 BISS key decryption (Mux mode) - Web-based NMS management
-
product
Multiplexer
SFT3107G
Hangzhou Softel Optic Co., Ltd.
SFT3107G Tuner Input Multiplexer is the latest demodulation and multiplexing device for digital TV broadcasting head-end system with TS output through IP port. It can multiplex up to 16 channels Tuner and 2 ASI input to IP (MPTS). This multiplexer has the functions of supporting auto-generation of PSI/SI information, PID re-mapping, and service filtering.
-
product
Analog Receiver / RF Tuners
The Bandit™ family of analog receivers or RF tuners provide a series of high-performance, stand-alone RF downconverter modules. These products offer a low noise figure, programmable gain and a high dynamic range and ensure there are no gaps in the RF spectrum coverage.
-
product
Demodulators and Tuners
ST offers standalone demodulation ICs for cable, satellite or digital terrestrial data transmission. Demodulation is also is integrated in many of our multimedia and application processor SoCs.
-
product
MFJ Dummy Load/Wattmeter
MFJ-267
1.5 kW Dry Dummy Load has built-in precision, true peak-reading SWR/Wattmeter switchable to external antenna! Worlds most versatile 1.5 kW dummy load has a built-in true peak reading SWR/Wattmeter that you can switch and use independently! Youll find tons of uses! Tune up your transceiver, linear amplifier, or antenna tuner into a safe 50 Ohm dummy load at full power.
-
product
Frequency Multipliers
Triplers
*No mechanical tuners*fullband operation*planar design*zero Bias
-
product
Automatic Tuners10MHz – 140GHz
Load Pull
An impedance tuner is an apparatus, which generates controllable reflection factor (Impedance) over a certain frequency range.
-
product
RF Power Delivery Systems
100 W to 2400 W 13.56 MHz Half rack mount or stand alone versions Air cooled (Air & Water 1200 W +) Analog & Digitial Interface Complete generator & tuner control via front panel GUI Software Includes all essential RF power/communication cables and mounting brackets
-
product
IRD
SFT356x
Hangzhou Softel Optic Co., Ltd.
SFT356X SD IRD is DEXIN’s all-in-one device which integrates demodulation, de-scrambler and decoding (DVB-C, T/T2, S/S2 optional) in one case to convert RF signals into analogue video (CVBS) output. It is a 1-U case which supports 2 tuner inputs. The two CAMs/CIs accompanied can descramble the programs input from encrypted RF, ASI and IP. The CAM requires NO unsightly external power cords, cables, or additional remote control device.
-
product
Noise Figure Measurements With Vector Correction
S96029B
This software application enables high-accuracy noise figure and noise-power measurements of amplifiers. It utilizes Keysight’s unique vector-source-correction technique, which uses a source-impedance tuner to remove the effects of imperfect system-source match. This approach yields accuracy that surpasses that provided by the Y-factor method and other cold-source implementations, especially for in-fixture, on-wafer, and automated-test environments. A scalar-calibrated method is also available that offers less accuracy but is faster and does not require an impedance tuner.
-
product
Noise Figure Measurements With Vector Correction
S95029B
The S95029B noise figure application enables high-accuracy noise figure and noise-power measurements of amplifiers, frequency converters, and mixers by using the Keysight vector-source-correction technique. Using a source-impedance tuner to remove the effects of imperfect system-source match, this technique produces higher accuracy results than Y-factor method and other cold-source implementations--especially for in-fixture, on-wafer, and automated-test environments.
-
product
Antenna Tuner
DU-1500T
The DU 1500T optimizes the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching.The DU1500T also measures the Power and Standing Wave Ratio (SWR), which allows you to tune the indicted SWR to the lowestpossible ratio for the selected transmit frequency.
-
product
SparkFun FM Tuner Basic Breakout
Si4703
This breakout for the Silicon Laboratories Si4703 FM tuner chip is a little more stripped down than our FM Tuner Evaluation Board. If your project already has an amp and just needs a full-featured FM tuner, this is the board for you. Beyond being a simple FM radio, the Si4703 is also capable of detecting and processing both Radio Data Service (RDS) and Radio Broadcast Data Service (RBDS) information. The Si4703 even does a very good job of filtering and carrier detection. It also enables data such as the station ID and song name to be displayed to the user.
-
product
Manual Tuners
Manual tuners are used both in the laboratory and as system components to establish or transform impedances for a number of applications. They can be used to establish optimum source or load terminations for device characterization, normalize a source or load for precision laboratory measurements and/or calibrations (noise, power, etc.), and can act as a matching transformer between a mismatched source and a mismatched load.
-
product
Inertia Single Roller Dynanometer for Motorcycles, for Flush-Floor Installation
MSR 400 | VP 630012
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 400 single roller inertia dynamometer for motorcycles is used in workshops for designers, tuners as well as educational institutions. It is perfect for dynamic power measurement with controllable acceleration as well as static power measurement at constant speed. The MSR 400 ensures the greatest measurement accuracy and reproducibility due to its active measurement of the towing power (measurement of the parasitic losses of the dyno, the losses in the vehicle's drive train and the friction losses from the tyres to the roller).
-
product
Automated Tuners / Impedance Tuners / Load Pull Tuners
MT97x, MT98x and XT98x series automated tuners (also known as automated impedance tuners and automated load pull tuners) are precision instruments that are optimized for a broad class of in-fixture and on-wafer applications, and may be used in any automated or manual application requiring the ability to match the impedance of a microwave circuit element or to establish specific impedances at a terminal interface. The tuner design is based on the slide screw concept using the inherently broadband slab-line transmission structure. Each unit has two non-contacting probes deliver high VSWR with superb accuracy and reliability over a wide frequency range. These probes can be fully retracted leaving a low-loss, well-matched transmission line, which is a significant benefit in power related applications where two-port tuners capable of handling large amounts of power are required. As integral components of Maury Device Characterization Solutions, these PC-based tuners are controlled using Maury's family of Device Characterization Software tools, including MT930 IVCAD, MT993 ATS and the DLL-based measurement automation environment. Maury Microwave automed impedance tuners are ideal for load pull, harmonic load pull, active load pull, hybrid active load pull, noise figure, noise parameters and all automated tuner applications.
-
product
Camera Detector
P7030
The easy to use Camera Detector is so small it can be carried or stored anywhere. Discreet sweeps of the home, office or hotel room can be done quickly and efficiently. When a camera is discovered, a LED light flickers and an audible alarm sounds. An auto adjusting sensitivity tuner allows you to scan variable distances and can check multiple channels. It can detect frequencies anywhere from 50 MHz to 3 GHz, picking up most wireless cameras.
-
product
Multichannel COMINT Receiver
HUGIN 2000
HUGIN 2000 Multichannel Receiver is the flagship of Novator Solutions COMINT receivers. The COMINT receiver utilizes one or two high-end wideband RF tuners and enable the users to monitor wideband spectrums and receive thousands narrowband channels.
-
product
BG Series Bass Amplifiers
250 Watt Bass Combos with Built-In TonePrints and Integrated Tuner.
-
product
Unitune Series Tuners
Clip-On Tuners with Strobe and Chromatic Modes and 108 LED Matrix Display for Uncompromised Tuning Quality.
-
product
Autotuner
HF-AUTO-R
The Palstar HF-AUTO-R is the full-function remote control unit for use with the HF-AUTO automatic antenna tuner. The HF-AUTO-R allows for remote operation of the HF-AUTO base unit up to 500' away and duplicates all buttons, controls, and display info.
-
product
IRD
SFT3975C
Hangzhou Softel Optic Co., Ltd.
SFT3975C HD IRD is SOFTEL’s new product which can receive signals from tuners (DVB-C, DVB-T/T2, DVB-S/S2/S2X, ATSC-T, ISDBT optional), ASI and IP. After demodulating, de-scrambling, re-multiplexing and decoding, it gives content out through various video/audio interfaces (HDMI, CVBS, 3G-SDI) or ASI or IP. This IRD is featured with two CAM/CI slots and BISS which supports to descramble encrypted Tuner, ASI or IP signals.
-
product
Slide Screw Tuners
Slide screw tuners are particularly suited to establishing impedances for device characterization, or for any other application requiring a precisely repeatable mismatch condition. This is due to the precision with which a specific matching condition can be repeated if the tuner has calibrated position indicators.
-
product
Frequency Multipliers
Doublers
*no mechanical tuners*fullband operation*planar design*bias voltage required
-
product
Handheld Performance Tuner
Max Energy
Max Energy Tuning extracts every bit of energy possible out of every molecule of fuel giving you more miles at part-throttle and more power at wide-open throttle. In order to increase engine efficiency, horsepower and torque, our engineers first optimize the spark and fuel curves point by point over the entire rpm band. With the additional power and optimized transmission functions, drivers use less fuel to accelerate and maintain cruising speeds without the torque converter un-locking and transmission down-shifting to a lower gear. The results are maximum power and fuel mileage.
