Tuners
Adjusts a signals frequency to one frequency or band of frequencies.
-
Product
Mux-scrambling Modulator
SFT3712
-
Hangzhou Softel Optic Co., Ltd.
SFT3712 Tuner input (SFT3712A ASI input) multiplexer scrambler is the latest multiplexing and scrambling device for digital TV broadcasting head-end system. The mux-scrambler 2 groups of ASI output and 2 corresponding IP output (share one gigabit DATA port, RJ45 interface). In conclusion, its high integration and cost effective design make this device widely used in the Next Generation of CATV Broadcasting system.
-
Product
Mechanical Noise Tuner Control
S93027B
-
The S93027B enables to control Maury Microwave’s LXI tuner as the impedance tuner and measure the noise figure of unmatched devices (Gamma opt. < 0.9) with the N524xB PNA-X with option 029 and the S93029B noise figure measurement software.
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 6U VPX
Model 57791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- One programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconvertersXilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x8- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Camera Detector
P7030
-
The easy to use Camera Detector is so small it can be carried or stored anywhere. Discreet sweeps of the home, office or hotel room can be done quickly and efficiently. When a camera is discovered, a LED light flickers and an audible alarm sounds. An auto adjusting sensitivity tuner allows you to scan variable distances and can check multiple channels. It can detect frequencies anywhere from 50 MHz to 3 GHz, picking up most wireless cameras.
-
Product
L-Band RF Tuner and 4-Channel 200 MHz A/D with Virtex-6 FPGA - 6U VPX
Model 58690
-
- Two L-Band tuners accept RF signals from 925 MHz to 2175 MHz- Two programmable LNAs boost LNB (low-noise block) antenna signal levels with up to 60 dB gain- Two programmable analog downconverters provide I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Four 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Demodulators and Tuners
-
ST offers standalone demodulation ICs for cable, satellite or digital terrestrial data transmission. Demodulation is also is integrated in many of our multimedia and application processor SoCs.
-
Product
Automatic Antenna Tuner
-
Automatic Antenna Tuner has not been released for full Beta testing and production yet as we are solving some firmware issues. We cannot give you a date nor estimate at this time when full production will commence.
-
Product
Single-Axle Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/1 CAR | VP 230035
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/1 single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/1 CAR guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.
-
Product
Analog Receiver / RF Tuners
-
The Bandit™ family of analog receivers or RF tuners provide a series of high-performance, stand-alone RF downconverter modules. These products offer a low noise figure, programmable gain and a high dynamic range and ensure there are no gaps in the RF spectrum coverage.
-
Product
Autotuner
HF-AUTO-R
-
The Palstar HF-AUTO-R is the full-function remote control unit for use with the HF-AUTO automatic antenna tuner. The HF-AUTO-R allows for remote operation of the HF-AUTO base unit up to 500' away and duplicates all buttons, controls, and display info.
-
Product
Amplifiers
LA-1K
-
Introducting the new LA-1K RF Sensing Dual HF LDMOS 1000 Watt Amplifier. While the LA-1K will work with a wide variety of tuners and transceivers, Palstar custom-designed the LA-1K to work as the perfect match for our very popular HF-AUTO autotuner. MADE IN THE USA
-
Product
Modulator
SFT3348T
-
Hangzhou Softel Optic Co., Ltd.
SFT3348T is a high performance and cost-effective DVB-T modulator designed by Softel. It has 8 DVB-S2 tuner inputs, after multiplexing, scrambling and modulating process, then it gives 4 RF output. To meet customers’ various requirements, this device is also equipped with 128 IP input and 4 MPTS output over UDP and RTP. Its pluggable structure design greatly facilitates the change of modules as needed. Moreover, the four CAMs/CIs accompanied can descramble the programs input from 8 Tuner inputs. SFT3348T can be upgraded and controlled through network system, which allows it to be widely used in setting up digital broadcasting network and provide good signals for scientific laboratory and DVB-T STB.
-
Product
FTTH Optical Node
SFT3908
-
Hangzhou Softel Optic Co., Ltd.
- Support 8 tuners (DVB-S/S2/S2X) input; 1 U chassis optional for 1/2/3 cards maximum for 8/16/24 tunerinput; Each tuner card are working independently with its NMS and 1 GE Data port - 8 MPTS (8MPTS out thru bypassing) under Passthrough mode over UDP/RTP thru Data port,unicast/multicast-Version 1 -2 MPTS out after multiplexing or 512 SPTS out switchable under Mux mode over UDP/RTP thru Data port, unicast/multicast-Version 2-Up to 256 PIDs remapping per output channel(Mux mode only) - Support PID re-mapping and pass-through(Mux mode only) - Support Diseqc function(Mux mode only) - Support Biss decryption, each tuner support maximum 64 BISS key decryption (Mux mode) - Web-based NMS management
-
Product
Talon 8 Channel 6 GHz RF Rugged Rackmount Recorder
Talon RTR 2628
-
- Eight-channel phase-coherent RF recording- Ideal for signal intelligence, phased-array radars, beamforming, and DF (Direction Finding) systems- Records RF frequencies from 30 MHz to 6 GHz- Captures 80 MHz of instantaneous bandwidth- Eight-channel RF tuner can be set for phase-coherent operation or independent tuning- Eight 250 MHz 16-bit A/Ds- Eight DDCs with decimations to 65,536 for selectable bandwidths- 3.2 GB/sec real-time aggregate recording rate- 4U 19-inch rugged rackmount PC server chassis- Windows® workstation with high performance Intel™ processor- Front panel removable SSD drives- Up to 122 terabytes of storage to NTFS RAID disk array- SystemFlow® GUI with signal viewer analysis tool- Optional GPS time and position stamping
-
Product
1100-Channel GSM Channelizer wih Quad A/D - PCIe
Model 78663
-
Model 78663 is a member of the Cobalt® family of high-performance PCIe boards based on the Xilinx Virtex-6 FPGA. This fourchannel, high-speed A/D converter with1100 GSM DDCs (digital downconverters) accepts IF signals from an RF tuner. It is ideal for capturing all transmit and receive signals in both upper and lower GSM bands.
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - PCIe
Model 78791
-
Model 78791 is a member of the Onyx® family of high-performance PCIe boards based on the Xilinx Virtex-7 FPGA. It is suitable for connection directly to an L-band signal for SATCOM and communications systems.
-
Product
Four-Wheel Drive Single Roller Dynamometer for Cars with Axle Load of 2.4T
MSR 500/3 CAR 4WD | VP 230037
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/3 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/3 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.
-
Product
Mux-scrambling Modulator 8 Ch
SFT3394C
-
Hangzhou Softel Optic Co., Ltd.
SFT3394C is a high performance and cost-effective QAM modulator designed by Softel. It has 16 DVB-S/S2 FTA tuner input to 16 non-adjacent carrier output with multiplexing, scrambling and QAM modulating included. It also supports maximum 512 IP input port and one IP (MPTS) output through GE1 and TS input for re-mux through 2 ASI ports. SFT3394C is also characterized with high integrated level, high performance and low cost. It supports dual power supply (optional). This is very adaptable to newly generation CATV broadcasting system.
-
Product
Autotuners
HF-AUTO
-
The Palstar HF-AUTO 1800 watt automatic antenna tuner covers 160 to 6 Meters with a power rating of up to 1800 watts PEP. Hams have enjoyed the benefits of low power auto-tuners for years, but now Palstar takes it to the next level and offers auto-tuning with a power rating of 5 Watts to 1800 watts.
-
Product
Transcoder
-
Hangzhou Softel Optic Co., Ltd.
SFT3248 (SFT3248B) is a professional bidirectional trans-coder to convert video between H.264 and MPEG-2 format and also to trans-code between HD and SD programs simultaneously. It is equipped with 6 tuner inputs to receive channels directly from satellite, or ASI /IP inputs to receive digital channels. (SFT3248B is a simple version with 4 Tuners only or 4 ASI inputs only without IP input.) After trans-coding, it outputs MPTS & SPTS through the DATA port or ASI port.
-
Product
Automatic Tuners10MHz – 140GHz
Load Pull
-
An impedance tuner is an apparatus, which generates controllable reflection factor (Impedance) over a certain frequency range.
-
Product
RF Switch Modules
-
Analog Devices RF switch modules include the highest bandwidth switch modules. SPST, SPDT, SP4T, SP6T, and SP8T versions (reflective and absorptive) are available for a wide range of power (up to 27 dBm) applications, including antenna switching, filter switching, and tuner applications.
-
Product
L-Band RF Tuner and 2-Channel 400 MHz A/D
Model 78891
-
Accepts RF signals from 925 MHz to 2175 MHz, Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm, Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz
-
Product
8-in-1 Transcoder
SFT3248
-
Hangzhou Softel Optic Co., Ltd.
SFT3248 is a professional bidirectional trans-coder to convert video between H.264 and MPEG-2 format and also to trans-code between HD and SD programs simultaneously. It is equipped with 6 tuner inputs to receive channels directly from satellite, or ASI /IP inputs to receive digital channels. After trans-coding, it outputs MPTS & SPTS through the DATA port or ASI port.
-
Product
Antenna Tuner HF+6m
DU 800 T
-
The DU 800 T optimizes the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching. The DU 800 T also measures the Power and Standing Wave Ratio (SWR), which allows you to tune the indiceted SWR to the lowestpossible ratio for the selected transmit frequency.
-
Product
L-Band RF Tuner and 2-Channel 500 MHz A/D with Virtex-7 FPGA - 3U VPX
Model 52791
-
- Accepts RF Signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to +10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Two 500 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously; optional: 400 MHz 14-bit A/Ds- Two FPGA-based multiband digital downconverters- Xilinx Virtex-7 VX330T or VX690T FPGAs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 & 3) interface, up to x4- Clock/sync bus for multimodule synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
IRD
SFT3975C
-
Hangzhou Softel Optic Co., Ltd.
SFT3975C HD IRD is SOFTEL’s new product which can receive signals from tuners (DVB-C, DVB-T/T2, DVB-S/S2/S2X, ATSC-T, ISDBT optional), ASI and IP. After demodulating, de-scrambling, re-multiplexing and decoding, it gives content out through various video/audio interfaces (HDMI, CVBS, 3G-SDI) or ASI or IP. This IRD is featured with two CAM/CI slots and BISS which supports to descramble encrypted Tuner, ASI or IP signals.
-
Product
Encoder-Modulator
SFT3542H
-
Hangzhou Softel Optic Co., Ltd.
SFT3542H24 in 1 encoder modulator is SOFTEL’s newest devices which integrate encoding, multiplexing, scrambling and DVB-C/T modulation. It supports 24 CVBS input, one DVB-C tuner input and 128 IP input with Data1 (GE) and Data2 (FE) port. It also support DVB-C/T RF out with 4 adjacent carries (50MHz~960MHz), and support Data1 (GE) output port to support 4 MPTS out. This full function device makes it ideal for small CATV head end system, and it’s a smart choice for hotel TV system, entertainment system in sports bar, hospital, apartment…
-
Product
Automatic Antenna Tuner 3.5 kW
DU 3500 AL
-
The DU 3500 AL automatic tuner has been primarily manufactured for an automatic PA, but it can also be used with any manual PAs as well. The tuner is primarily compatible with the OM POWER automatic PA.This tuner was designed for antennas calibrated to HAM BANDs. The maximum power can only be utilized with these antennas. With other antennas, it should be set at a lower power (max. 2kW).The major advantage of the tuner is that during competitions it is possible to change BANDs particularly quickly.
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD can also be extended with a 3rd or 4th eddy current brake.
