Adapters
Interfaces that facilitate interconnect between two dissimilar elements.
-
Product
Coaxial Waveguide Adapter, 1.0 mm (f), 75 to 110 GHz
W281C
Coax Adapter
The Keysight W281C is a 1-mm female to W-band waveguide adapter with a frequency range of 75 GHz to 110 GHz. The Keysight W281C is used with the Keysight 8510XF systems.
-
Product
PCIe Adapter for XMC
PCIe8LXMCX1
-
Simple and easy to use. Install PCIe8LXMCX1 into your PCIe system to adapt an XMC card. The XMC can have bezel and or rear IO. Pn4 and/or Pn6 are supported with PCIe8LXMCX1. 8 lanes are routed from the PCIe gold fingers to the XMC position.
-
Product
OX 774 WDM Node
-
- Two Output - Sensitivity: -16dBm- Output Level: 85 dB- Operates With 12V ONU Adapter- DC to DC Cable-2.5 / 1.5 mm Plug provided- Use with PSP (STB Adapter)
-
Product
Test and Analysis
-
ESDEMC Technology will calibrate; the Contact Mode ESD current waveform and tip voltage to 4 GHz and 30 kV, the frequency response of ESD Target & Adapter Line to 4 GHz, and the DC Resistance
-
Product
Adapter, 1.0 mm (m) to 2.4 mm (m), DC to 50 GHz
11922A
Coax Adapter
The Keysight 11922A precision 2.4 millimeter coax in adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and a frequency range from dc to 50 GHz.
-
Product
Adapter Kit, 3.5 mm
83059K
Accessory Kit
The Keysight 83059K adapter kit includes the 83059A 3.5-mm male adapter, the 83059B 3.5-mm female adapter, and the 83059C 3.5-mm male to 3.5-mm female adapter.
-
Product
High-Stability Adapter
10723A
Accessory Kit
The Keysight 10723A high-stability adapter converts the 10706A Plane Mirror Interferometer into an 10706B High-Stability Plane Mirror Interferometer. The 10706B is a thermally-stable optic with measurement drift reduced to approximately 1/12 the value achieved by conventional plane mirror interferometers.
-
Product
Air Data Adapter Test Panel
TA-241
-
AZ-241 Adapter Panel is designed to meet manufacturer's requirements. This panel will allow by the book testing of the air data computer when interfaced with the main air data test fixture. The Scott-T transformer is optional or can be customer supplied. Without the Scott-T your API can read the altimeter resolver directly.
-
Product
SM / Expansion Unit
-
A testing procedure designed to thoroughly test the electrical characteristics of a wire or cable, may require additional test points to connect the end points of all conductive paths. The changing and alteration of Test Adapter Cables (TACs) would become obsolete when having access to one or several expansion units. Increased testing efficiency alleviates the long, drawn out down times of the disabled aircraft while improving product readiness. Additional time can be spent on troubleshooting and problem identification and will not require the user to unhook and connect TACs to different matrices. Adding additional expansion units will save the user time, money, and effort.
-
Product
Adapter/Stainless Steel
WADP-24FSM
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customers demand. All Warisons products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to 2 PCB-Mounted 12X Male InfiniBand Connectors (LVDS)
510150210
PCB Adapter
PCB Adapter, Receiver, QuadraPaddle, 192 Position, to 2 PCB-Mounted 12X Male InfiniBand Connectors (LVDS)
-
Product
USB Graphics Adapter, Internal Mount, DB-15 connector
DB-UVGA16
Graphics Card
- Mounts in DB9 cutout on chassis or in PCI slot- Uses internal USB pin header- Display resolutions up to: 1600 x 1200 (4:3), 1680 x 1050 (16:10)- Supports multiple display modes: Primary, Extended, Mirr
-
Product
Adapter/Stainless Steel
WADP-QSMSF-01
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Low-Profile PCI-to-CardBus/PCMCIA/PC-Card Adapter, 1 Rear Slot, Universal
P311
-
This product is recommended for Systems Integrators and OEMs only due to the non-standard "volume envelope" that is required around the host's PCI connector.
-
Product
PXI Pull-Thru Adapter, Single Slot, 6.75" Series Adapters, 1 Module Position
510109461
Pull-Thru Adapter
PXI Pull-Thru Adapter, Single Slot, 6.75" Series Adapters, 1 Module Position
-
Product
PCI bus Test Adapter
pcibus1b
-
All important PCI bus signals routed to pin headers for easy connection of logic analyzer. Filter assistance for logic analyzer: D-FF to delay FRAME# by one cycle. To see actual PCI data transfers, filter for FRAME2# high + FRAME# low (address phase), or IRDY# low and TRDY# low (data phase). Business card size. Notched for 5V PCI bus (can be used on 3.3V bus with mechanical modification).
-
Product
PXI Pull-Thru Adapter, Wired, QuadraPaddle, to Two 68 Pin Male VHDCI
510140114
Pull-Thru Adapter
PXI Pull-Thru Adapter, Wired, QuadraPaddle, to Two 68 Pin Male VHDCI
-
Product
D.V.A. Adapter
640
-
*Read peak volts on CD ignition coils with your existing digital multimeter *New, completely redesigned unit is half the size of the previous adaptor *Adapts standard digital multimeter into peak reading voltmeter *High quality test leads with alligator clips are incorporated into the adaptor
-
Product
USB to TTL Adapter
SKU-012-0X
-
The USB to TTL adapter connects the Serial UART to the standard USB port for testing and monitoring functionality. The Adapter facilitates ease of use and helps to reduce board space and cost.
-
Product
XMC-to-PCI Express Adapter
4823
-
The Technobox, Inc. P/N 4823 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 1x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
Resistivity Cell For N1413 (26/50 Mm Electrodes)
N1424B
Resistivity Cell
The N1424B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424B to the B2985B/87B.
-
Product
ITA, G20, 20 Module, EMI, 2"
410120223
ITA
ITA, G20, 20 Module, 6.75" Series Adapter, EMI, 2"
-
Product
SHC68-C68-D4 Shielded Single-Ended Cable, 0.55 m
781013-01
Digital Cable
68-Pin, Male VHDCI to 68-Pin, Male VHDCI, 50 Ω, 0.55m, Shielded Digital Cable - The SHC68-C68-D4 Digital Cable connects NI 6535/6/7, 654x, 655x, and 657x digital instruments with other NI accessories like the CB-2162 Connector Block or SMB-2163 Terminal Block. You can also use it with certain Digital I/O Adapter Modules for FlexRIO, Digitizer Adapter Modules for FlexRIO, Signal Generator Adapter Modules for FlexRIO, and high-speed serial instruments. It is flexible and easily fits around custom test fixtures and other equipment. It is a shielded, 50 Ω cable and is offered in different lengths.
-
Product
Test Adapters
-
In our specially developed MG range of linear test adapters (test fixtures), we use solid aluminium components in our mechanical construction. This is to ensure the reliability and contact accuracy of the test adapter.
-
Product
ITA 192-Pin PCB Adapter to 3x IDC 64
YAV90Q06
PCB Adapter
3x 2 IDC 64 x 1000mmCables set J6200560 (Order Separately)
-
Product
Dual Port Fiber 100GbE Ethernet PCI Express Server Adapter With NVIDIA® ConnectX®-6. Ideal For High-Performance Data Center Networking.
PCIE-2421NP
-
NVIDIA® ConnectX®-6 Dx Controller2 100GbE QSFP56 portsPCIe Gen. 4 x16 host interfaceLow profile (half length) form factorsSupports 100GBASE-SR4, 100GBASE-CR4 and 100GBASE-KR4 modulesSupports SR-IOV based virtualization
-
Product
Coaxial Waveguide Adapter, 1.85 mm (m), 50 to 67 GHz
V281B
Coax Adapter
The Keysight V281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
PMC (ccPMC VITA 20)-to-4X PCI Express (PCI-e/PCIe) Adapter
6768
-
Our conduction-cooled adapter that permits the insertion of a single PMC into a PCI Express (PCIe/PCI-e) slot (4X). The adapter orients the ccPMC in a reverse manner such that the rear I/O from PN4 appears at the 68-pin SCSI-style connector installed on the adapter’s bracket.
-
Product
NF-SF 50 N-Female to SMA-Female Adapter
-
NF-SF 50 Adapter, N-Female to SMA-Female, Frequency Range: DC to 18 GHz, Impedance: 50 Ohm
-
Product
PCIe and VPX Compatible Adapter Carrier
PCIe2VPX3UX4
-
The power supply designs utilize switching regulators controlling MOSFET´s. An LC filter insures clean power at the VPX device. The PCIe gold fingers are rated for 1.1A each, and a total of 5.5A on the +12V rail. 55W are available to the card after power conversion.
