Standards
A controlled reference or acknowledged technical criterion.
See Also: IEC, IEEE, Mil, Interoperability Test, Compliance
-
Product
Electrical Safety Testers
-
A high performance electrical safety analyzer that complies to a wide range of universal standards. Hipot, Insulation Resistance, Ground Bond, Leakage Current (touch current and protective conductor current) and partial discharge can all be tested. A total of 6 models are available for standard compliance tests in a wide variety of applications including R&D, quality assurance manufacturing lines and laboratory tests.
-
Product
FMC for High Speed Optical Communication Dual QSFP+ FMC
FMC424
-
Sundance Multiprocessor Technology Ltd.
The FMC424 is a dual QSFP+ FPGA Mezzanine Card. Electrically compliant with the VITA 57.1 standard the FMC424 is compatible with 4DSP FPGA carrier cards offering High Pin Count connectors. It also allows for the option to stack an additional FMC over it. Any of the 4DSP FMC that use LVDS and single ended signaling only can be mounted over the FMC424, thus offering users with the ability to build a complete high speed data acquisition, waveform generation and optical communication solution while using a single FMC site on an FPGA carrier card.
-
Product
Stress screening test chambers for temperature and climate
TS and CS series
-
Our based on the modular concept of the standard range of temperature and climatic stress screening test chambers allow you through increased compressor and large fan performance very high temperature change of up to 30 K / min with conventional refrigeration, or to 70 K / min with liquid nitrogen. These devices allow you to very quickly determine the load limits of your test object in fast motion.
-
Product
Torque Wrenches
-
Recommended torque for various connectors has changed slightly through the years, current standards often being slightly less than before. The recommended torque depends upon whether a connector is stainless steel or brass. The SMA recommended torques have the most variables, with stainless steel sma's for final installation being 8-10 in-lbs, preferably 8; stainless steel sma's in the test lab are best tested at 5 in-lbs to preserve the sma; & brass sma's are 4 in-lbs. Most of these torque wrenches are "ours" however we also carry the Huber Suhner sma torque wrenches, the 74Z-0-0-21 & 74Z-0-0-79 as they're so popular. Our torque wrenches are preset to specific values.
-
Product
Laboratory Freezer
FZ Series
-
The FZ series laboratory freezer chambers are designed for performance specifications exceeding FDA and ICH requirements. The FZ series freezer chambers comes standard with the following performance: Solid- State Temperature Control. Autodefrost. Standard Microprocessor Controller with PID, Autotuning, programmable alarms (hi/lo), ability to ramp/soak, process variable and setpoint variable offset, dual display of actual temperature and setpoint temperature (process variable and setpoint variable). Controls are able to be quickly exchanged for future upgrades or repair.
-
Product
LogiCue Systems
LogiCue 6
-
The LogiCue 6 controller has many of the same features as the LogiCue 12. It has 6 channels of control, LED indicators that mimic the color of each channel, a 2-way “acknowledge” feature that allows actors or crew members to respond to the stage manager with the press of a button, and self-test on power up. The controller connects to the cue lights using standard microphone cable.
-
Product
Integrated Laser Controller + Servo
SILC
-
Discover our integrated laser controller with servo which has all the features of the standard ILC with additional servo features.
-
Product
Display ICs For Automotive
-
Renesas has invested in key technologies to address the latest trends within the automotive market. Offering both standard and AEC-Q100 qualified products for automotive applications, Renesas' automotive display IC product line is defined by feature rich, highly integrated semiconductor solutions that incorporate many key function blocks for front console, rear seat entertainment, and rear camera display applications.
-
Product
PCI Express To PCI Express Expansion With 3 PCIe Gen-2 Slots
ExpressBox 2200
-
Precision engineered to Magma’s mission critical standards for performance and reliability, ExpressBox 2200 features three (3) full-length, full-height PCIe slots and flexibility with eight (8) 2.5-inch SATA/SAS HDD or SSD hard drive bays. Designed with your workstation in mind, the EB2200 has a rack-mountable aluminum chassis for integrated removable storage expansion, a 520-watt fanless power supply, auxiliary power, and features Magma’s exclusive quiet cooling control.
-
Product
10 Digit Rate/Batch Counter (Analogue)
CS2-TM-Analogue
-
The CS2-TM Totalizer controller provide high accuracy measurement, display, control and communication (Modbus RTU mode) of 0~10V/4~20mA from flow meter or mV from Shunt for Amp-Hour.There are two display screen and 3 external control input (DI) in standard and the optional 4 Relay, 1 Analogue, 1 Pulse and RS485 port available. They are also support fantastic control function as like as N, R, C mode for totalizer and batch control.
-
Product
Meter Test System
MTS-50
-
Kongter Test & Measurement Co., Limited
This meter test equipment features state-of-art designing with high accuracy. It is composed of high accurate (class 0.05% or 0.1%) standard reference meter and power source (up to 50A). This system is particularly designed with modular structure for calibration and test of different single phase/3 phase electronic/inductive active and reactive energy meters.
-
Product
ISA DIO 96 Board
MS 1805
-
*Discrete Input / Output - 96 Channels*All Channels are compatible with 5V TTL / CMOS*Standard ISA Bus Interface*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Multi-Laser Light Source
LS-n
-
The LS-n is a customizable, compact fluorescence excitation source that provides up to four different laser wavelengths in a single combined output beam, with each laser individually controllable using ANF's custom software. An LS-4 unit (containing four lasers) is included with each standard NFM NanoFluorescence Microscope.
-
Product
Controlled Impedance Analyzers
-
HYPERLABS Controlled Impedance Analyzers can be used with various probes and adapters to quickly and reliably characterize impedance on PCB test coupons. These Test Systems are designed to comply with IPC-2141A standards for PCB coupon testing, and can be customized to meet specific customer needs.
-
Product
X-ray Diffraction and Elemental Analysis
D2 PHASER
-
The D2 PHASER is the most compact and fastest, all-in-one crystalline phase analysis tool available on the market. It is mobile and easy to install with only the need for standard electrical power. The D2 PHASER is therefore ideal for laboratory or on-location operation, in other words, it is a true Plug'n Analyze system.
-
Product
cPCI to PMC Adapter / Carrier
cPCIBPMC
-
The cPCIBPMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCIBPMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
Product
PXI-5670, 2.7 GHz PXI Vector Signal Generator
PXI-5670 / 778768-01
Vector Signal Generator
2.7 GHz PXI Vector Signal Generator—The PXI‑5670 has the power and flexibility you need for product development applications from design through manufacturing. It can generate custom and standard modulation formats such as AM, FM, PM, ASK, FSK, PSK, MSK, and QAM. The PXI‑5670 delivers a highly flexible and powerful solution for scientific research, consumer electronics, communications, aerospace/defense, and semiconductor test applications as well as for emerging areas including software defined radio, radio frequency identification (RFID), and wireless sensor networks.
-
Product
USB Modular Digital Multimeter, 5 digit
U2741A
Digital Multimeter
The Keysight U2741A USB Modular Digital Multimeter provides a broad range of measurement functions, including temperature and frequency. The U2741A is a 5.5-digit resolution digital multimeter that is able to capture up to 100 readings/sec. It uses the common non-proprietary standard high-speed USB 2.0 interface that provides ease of connectivity allowing users to set up and configure their tests swiftly with its plug and play feature.
-
Product
Radius, Standard 0.61 (17.00) - 2.80 (79.00) General Purpose Probe
HPA-0D
General Purpose Probe
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 635Overall Length (mm): 16.13
-
Product
ETAP Protection & Coordination
-
Analyze and evaluate the performance of power system protection with intelligent tools and powerful capabilities from ETAP. The ETAP Protection and Coordination solution is an integrated collection of intelligent tools designed to analyze, evaluate, and automate power system protection. This solution drastically reduces engineering time by providing targeted functionality for precision protection system simulation and analysis against industry standards.
-
Product
Digital Panel Meters
-
For more than 40 years, the Murata Power Solutions offering of digital panel meters has been recognized as the industry's most versatile and have been expertly designed for a variety of applications. If a standard product does not meet your requirements, our experienced team of designers can quickly develop a custom solution.
-
Product
2.0J Impact Hammer
CX-T20
-
Shenzhen Chuangxin Instruments Co., Ltd.
Required by many Standards to test the mechanical integrity of product enclosures. After applying the impact with the hammer, the product is examined with accessibility probes to determine access to shock, energy, and injury hazards. Built in exact accordance to IEC, EN, UL, CSA and other international Standards.
-
Product
Continuous Emissions Monitoring
atmosFIR CEM
-
atmosFIR CEM is a complete emissions monitoring system incorporating the atmosFIR 19” FTIR analyser. As completely hot and wet emissions measurement, atmosFIR CEM is ideal for complete measurement of multiple gases from applications such as incineration and power. A standard gas suite of NO, NO2, N2O, SO2, NH3, HCl, CH4, O2, CO2 and H2O is provided, but with the powerful FTIR analyser, further gases can be added easily in software.
-
Product
Standard 0.62 (18.00) - 4.00 (114.00) High Performance Bias Ball Probe
POGO-1Z1-4-S
ICT/FCT Probe
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
Product
Cots Boards
-
Built in strict adherence to open architecture standards, Data Patterns designs COTS module products which are used in today's rugged applications and automatic test equipment platforms. Open standard form factors include cPCI, FMC & XMC, IP, MM, PCI, PCMCIA, PMC, VME, VPX and VXI.A portfolio of 'Off the Shelf ' products for testing and on-board applications have been developed by Data Patterns. COTS boards developed have been sold to many customers, in India as well as Europe and North America. They are used for system level products such as Automatic Test Equipment, Rugged Military Electronics, etc.Data Patterns focus on building COTS product is to provide the technological capability to develop system level products with very fast run around times. Use of Data Patterns' COTS module in system level products ensures Data Patterns ability to maintain the products for a significantly longer life cycle. The proximity to the system level engineering team with the COTS development team ensures that end applications are delivered faster, enabling a shorter time to market for the customers
-
Product
700-Watt AC/DC Power Supply
VPX56-6
Programmable Power Supply
NAI's VPX56-6 is a 700-Watt AC/DC Power Supply which accepts either a 3 115Vac L-N inputs or a +270Vdc input. It plugs directly into a standard 6U VPX chassis with a (VITA 62) 1.0" power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
cPCI to PMC Compatible Adapter/Carrier
cPCIBPMC6UET
-
cPCIBPMC6UET ( cPCI to PMC ) adapter / carrier converter card provides the ability to install up to two PMC cards into a standard cPCI slot. cPCIBPMC6UET has two PMC card slots mounted to a universal voltage 6U 4HP cPCI card.
-
Product
High Voltage AC/DC Dividers
-
Sphere Gaps are absolute standards for measurement & calibration purposes of high voltage equipment Sphere Gaps from 20mm to 1500 mm are available. The Sphere Gaps are provided with automated controls with digital display.
-
Product
Encoder
SHP400
-
Hangzhou Softel Optic Co., Ltd.
This user manual has been written to help people who have to use, to integrate and to install the product. Some chapters require some prerequisite knowledge in electronics and especially in broadcast technologies and standards.
-
Product
Battery-Monitoring
NERC
-
NERC PRC-005 is the standard for Protection Systems Maintenance and Testing. PRC-005 continues to be the most commonly violated NERC reliability standard in North America. PRC-005-2 requires utilities to document and implement programs for the maintenance of all protection systems affecting the reliability of the Bulk Electric System (BES). All VLA, VRLA and NiCad Batteries are required to be verified, inspected, monitored & calibrated to meet PRC-005-2 Compliance.
