-
Product
Coaxial Waveguide Adapter, Type-N (f), 8.2 to 12.4 GHz
X281A
-
The Keysight X281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
E Bend Waveguide
-
E-plane waveguide bends are sections of high-precision crafted waveguides and shaped to either 30º, 45º ,60º, or 90º angles for e-plane needs. It directs the radio frequency beam and “bends” the signal to go the direction you want. Think of it like Tokyo drifting around a corner in your car. Precision MMW will help you with the highest quality E bend waveguides. We are a millimeter wave spectrum manufacturer of various active and passive mmWave products and sub-system engineering.View more E Bend Waveguide
-
Product
Waveguides
-
A waveguide attenuator is an RF device specifically designed to reduce the power of a signal without affecting or reducing the waveform of the signal.
-
Product
Mechanical Calibration Kit, 12.4 To 18.0 GHz, Waveguide, WR-62
P11644A
Mechanical Calibration Kit
The Keysight P11644A calibration kit contains the precision mechanical standards required to calibrate the systematic errors of Keysight network analyzers. This calibration kit has a precision airline for performing the thru-reflect-line (TRL) calibration, the most accurate error-correction technique for coaxial measurements. This kit also contains a commercial calibration certificate, flush short circuit, a precision shim, and fixed termination(s).
-
Product
K-Band Waveguide Gunn Oscillator Module
FMWGN1001
-
FMWGN1001 is a K Band Waveguide Gunn Oscillator with a Center Frequency of 24.125 GHz and a Tuning Range of +/- 1.0 GHz. The unit has a Phase Noise @ 100kHz Offset of -95 dBc/Hz typ and Frequency Stability of -0.4 MHz/°C max. The Gun Oscillator has an Output Power of 10 dBm min and Power Stability of -0.04 dB/°C max. The Waveguide Gun Oscillator uses a Bias Voltage of 5.0 Volts and a Bias Current of 200 mA and has a Waveguide Size of WR-42 with a UG-595/U Flange.
-
Product
Double Ridged Waveguide Horn
TEMH20
-
Frequency range: 1 GHz - 22 GHz VSWR (max): < 2.6:1Impedance: 50 O (Ohm)Connector: 3.50mm female Power (CW / Peak): 20 W / 50 W
-
Product
Coaxial Waveguide Adapter, 1.0 mm (f), 50 to 75 GHz
V281C
-
The Keysight V281C is a 1-mm female to V-band waveguide adapter with a frequency range of 50 GHz to 75 GHz. The V281C is used with the Keysight 8510XF systems.
-
Product
Waveguide Adapter
-
Waveguide adapters in a variety of waveguide standards / flange types and coaxial connectors
-
-
Product
Millimeter Wave Control Devices
-
Ducommun millimeter wave products include various control devices for system integration. The CAE, CPS, CPD and CPM series control devices are discrete or MMIC based PIN diode attenuators and switches. The CAF, CAL, CAR and CPL series control devices are waveguide based mechanical tunable attenuators and phase shifters. These devices are offered to cover the frequency range from 18 GHz to 110 GHz.
-
Product
Waveguide Calibration Kits
-
Designed to provide accurate calibration of vector network analyzers (VNAs) that are used for measurements in standard rectangular waveguide from 2.6 to 50 GHz (WR284–WR22).
-
Product
Passive Waveguide Components
-
We cover all kinds of connections between waveguide, coaxial, micro-strip and co-planar lines. Filters are available in waveguide technology as well as in stripline/micro-strip. Passive structures such as power splitter, power combiner, ortho-mode transducer and hybrids mostly are designed to meet the specific goals of the customer.
-
Product
Waveguide Duplexer
-
RF Lambda’s waveguide duplexers are used to combine two frequencies onto a common waveguide. They offer high isolation and low insertion and come in a variety of frequencies. Hermetically sealed options are available upon request.
-
-
Product
Waveguide Harmonic Mixers (smart mixer), 50 to 75/80 GHz
M1970V
Harmonic Mixer
The Keysight M1970V 50 to 75/80 GHz waveguide harmonic mixer is an un-preselected mixer that will extend the operating frequency range of the N9030A PXA, N9020A MXA, and N9010A EXAsignal analyzers up to 80 GHz. Smart features are embedded to help you to greatly simplify your overall test setup and improve your DANL and TOI of your test system. Go smart with harmonic mixing for your millimeter-wave applications.
-
Product
Waveguide To Coaxial Adapter
D25-BWC26NK-260
-
Waveguide To Coaxial Adapter, Frequency2.17~3.3GHz, Power 500W, WR340, Flange FDP26, N Type Female Connector
-
Product
Millimeter Wave Frequency Counter 70-170 GHz
-
Insight Product Co. offers the electronic frequency counter for frequency measurements of millimeter wave generators of continuous or pulsed signals. The counter has an auto and waiting modes of operation and a direct 6-digits reading in frequency range (70-170) GHz without an external mixer.
-
Product
Waveguide Variable Attenuators
-
A variable attenuator from Pasternack. This SMA microwave attenuator is a continuously variable attenuator design.
-
Product
Coaxial Waveguide Adapter, 3.5 mm (f), 18 to 26.5 GHz
K281C
Coax Adapter
The Keysight K281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can be transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.07.
-
Product
Waveguide Circulator/Isolator
-
RF Lambda’s waveguide circulators are typically used to prevent unwanted reflections. They offer low insertion loss and high isolation and are available in a variety of frequencies and power levels.
-
Product
Ferrites and Waveguides
-
Wide range of Ferrite Devices Waveguide products for a variety of commercial, defence and space applications. The breadth of products includes devices operating from 1.0 to 52.0 GHz and includes isolators and circulators, combiners, transitions and terminations. Power combiners & dividers, Iso-adapters, WG loads, Isolators & circulators are offered in drop in, connectorized and micro-strip versions.
-
Product
E & W-Band PIN Diode Waveguide Switches
-
Fairview Microwave’s single-pole single-throw (SPST) and double-pole double-throw (DPDT) PIN diode waveguide switches feature fully integrated WR-10 and WR-12 waveguide ports and cover popular E-band (60 to 90 GHz) and W-band (75 to 110 GHz) frequencies. Switch circuits integrate low loss Fin-line assemblies with high performance GaAs beam-lead diodes that results in 4 dB insertion loss, greater than 25 dB of Isolation and fast switching speed < 300 nsec.
-
Product
WR-12 Waveguide Straight
WAG-12-SXX
-
• 60 GHz to 90 GHz• Low Insertion Loss, typical for length• Low Return Loss, typical for length• UG-387 flangeView more WR-12 Waveguide Straight
-
Product
Coaxial Waveguide Adapter, 1.85 mm (f), 50 to 67 GHz
V281A
-
The Keysight V281A adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Millimeter Vector Network Analyzer
MVNA-8-350-4 and 4S
-
The microwave part MP-8-350-4 is designed for the 4S-Parameter measurements. It includes two connectors for the two detectors HM like in MP-8-350-2, and also two connectors for the two sources HG, which are powered alternatively.
-
Product
Double Ridged Waveguide Horn
DRH40
-
Frequency range: 4 GHz - 40 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: K female Power (CW / Peak): 15W / 30 W
-
Product
Waveguides
-
Learn about waveguides at Precision MMW. This is a handy waveguide tutorial for the everyday mmWave engineer.Learn more on Waveguides at Precision website here.
-
Product
Coaxial Waveguide Adapter, 1.0 mm (f), 75 to 110 GHz
W281C
-
The Keysight W281C is a 1-mm female to W-band waveguide adapter with a frequency range of 75 GHz to 110 GHz. The Keysight W281C is used with the Keysight 8510XF systems.
-
-
Product
Waveguide Electromechanical Relay Switches C, X, Ku, K & Ka Bands up to 40 GHz
-
Waveguide Electromechanical Switch models cover C, X, Ku, K, Ka frequency bands up to 40 GHz. SPDT and Optional DPDT* Configurations with Latching Self Cut-Off Actuators, TTL Logic, and Position Indictors with manual override. Patented Motor Drive with Arc Suppression. Designs support WR-137, WR-112, WR-90, WR-75, WR-62, WR-42, and WR-28 waveguide sizes with O Rings for pressurized operation. Power handling capability up to 12 kW CW and 320 kW Peak. These waveguide electromechanical relay switches deliver desirable performance that includes high isolation levels up to 105 dB, and extremely low insertion loss down to 0.01 dB.
