Waveguides
guide the propagation of electromagnetic, light or sound waves.
See Also: Millimeter Waveguides, Optical Waveguides
-
Product
60 GHz Noise Figure Test Set
-
The Noisecom 60 GHz Noise Figure test set has 4 separate systems designed to perform Y-factor noise figure measurements using a high performance Spectrum Analyzer or a dedicated receiver. Each system contains a highly stable V-band noise source, isolator(s), optional waveguide to coaxial transitions and an optional pre-amplifier for use with a spectrum analyzer. The two standard calibration tables have ENR data points at 1 GHz intervals.* System ENR is measured before the DUT connector and at the final output stage allowing for pre-test calibration of the system.
-
Product
Full Band Phase Shifters
STP-18-10-M2
-
Full band phase shifters are micrometer-driven, waveguide-based phase shifters. The configuration of the micrometer-driven phase shifters is similar to that of level setting attenuators, where the phase shifting is caused by an E-plane dielectric insert in the rectangular waveguide. The amount of phase shifting is directly dependent on the volume of the insert. The VSWR and the insertion loss of these phase shifters are dependent on the frequency. The below standard offering covers the frequency range of 18 to 110 GHz and a phase shifting range of 180 degrees. These micrometer-driven phase shifters are typically used to introduce a certain amount of phase shifting when the absolute number is not a focus.
-
Product
Flexible Waveguide
-
Flann offers a number of solutions for flexible waveguide interconnect including waveguide-coaxial-waveguide and semi rigid. Traditional flexible waveguide solutions are available on request.
-
Product
Low Noise Amplifiers
-
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a wide range of applications but are primarily suited to communication systems including both Data-Link and Satellite Communications (Satcom) systems. Our new K-Band LNA operates over a 19.2 - 21.2 GHz with 1.3 dB Noise Figure at 25°C. It is configured with a waveguide input and 2.92 output connector all in a hermetic package.
-
Product
Harmonic Mixers
-
These waveguide bandwidth harmonic mixers are designed for use with spectrum analzyers with diplexers, such as the Tektronix 492 and 494 and the Hewlett-Packard 8555A, 8565A and 8569A. They are also used as phase locking and receiver mixers for antenna measurement systems such as the Scientific Atlanta wide range receivers. When used with an external diplexer*, these harmonicmixers can be used to phase lock millimeter wave sources.
-
Product
Mechanical Calibration Kit, 18 To 26.5 GHz, Waveguide, WR-42
K11644A
-
The Keysight K11644A calibration kit contains the precision mechanical standards required to calibrate the systematic errors of Keysight network analyzers. This calibration kit has a precision airline for performing the Thru-Reflect-Line (TRL) calibration, the most accurate error-correction technique for coaxial measurements. This kit also contains a commercial calibration certificate, flush short circuit, a precision shim, and fixed termination(s).
-
Product
Electronics
-
Flann provides control processors and switch drivers that support all Flanns current range of programmable attenuators, phase changers and waveguide switches
-
Product
Millimeter Wave Continuously Variable Waveguide Attenuators
-
Our millimeter wave variable waveguide attenuators allow designers and engineers to test their systems at various signal strengths and attenuation values to determine the optimum signal performance of the system. The key feature of these waveguide attenuators is that the attenuation level is adjusted using a built-in micrometer which enables repeatable and rapid re-setting to different attenuation levels without the need for additional external components. Our waveguide attenuators handle varying attenuation levels from 0 to 30 dB over the specified band allowing the designer to tune the attenuation level needed for the application. These continuously variable waveguide attenuators cover a broad frequency range of 33 to 110 GHz in five bands and also display flat performance across a wide band with low insertion loss.
-
Product
Double Ridged Waveguide Horn
H-A50
-
Frequency range: 33 GHz - 50 GHz VSWR (max): < 1.35 :1Impedance: 50 O (Ohm)Connector: 2.4 female Power (CW / Peak): 10 W / 20 W
-
Product
Double Ridged Waveguide Horn
DRH18–E
-
Frequency range: 1 GHz -18 GHz VSWR (max / AVG): < 3:1 / 1.35:1Impedance: 50 O (Ohm)Connector: SMA female / N femalePower (CW / Peak): 50 W / 100 W
-
-
Product
Microwave Testing
140
-
The PICOPROBE® MODEL 140, a high performance microwave probe which incorporates a WR-8 waveguide with our patented coaxial design techniques, has inherent low loss and low dispersion characteristics.
-
Product
Coaxial Waveguide Adapter, 2.4 mm (m), 33 to 50 GHz
Q281B
-
The Keysight Q281B is a 2.4 mm male to WR-22 waveguide adapter that operates in the 33 to 50 GHz frequency range. These adapters transform waveguide transmission lines into 50 ohm coaxial lines. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
Product
Varactor Tuned Gunn Oscillators
-
Varactor tuned Gunn oscillators utilize high performance GaAs Gunn diodes and various cavity configurations to deliver moderate output power with low AM/FM noise and harmonic emissions. The oscillators are specially designed for a broader tuning bandwidth and an electrical tuning capability. The standard offering covers the frequency range of 8.2 to 110 GHz and features a self-locking set screw for fine frequency setting. While standard models offer a waveguide interface, a coaxial interface is also available. The performance of the oscillator can be further enhanced by adding an isolator, Gunn oscillator modulator/regulator, and temperature heater.
-
Product
Waveguides
-
A waveguide attenuator is an RF device specifically designed to reduce the power of a signal without affecting or reducing the waveform of the signal.
-
Product
Waveguide To Coax Adaptors
-
The transitions from waveguide to coaxial line (SMA connector type) are offered up to 110 GHz.
-
Product
Standard Gain Horn Pyramidal Horn Antenna
-
Elva’s SGPH series of standard gain horn antennas cover the frequency range of 18 to 220 GHz in ten waveguide bands. They can be issued with rectangular or circular waveguide. Lens technology significantly allows decreasing mechanical sizes of horns and correcting beam for the best performance. These horns are ideal solution for measurement gain of other antennas, short range radars and radiometers.
-
Product
Microwave Antennas
-
We are engaged as leading Microwave Antenna manufacturers andexporter of a wide range of Microwave Waveguide Antenna, Waveguide Antenna, Parabolic Microwave Antenna, Conical Microwave Antenna and Pyramidal Microwave Antenna.
-
Product
Conical Horn Antennas
-
Conical gain horns are offered as both standard and custom models with either a circular or rectangular waveguide interface. While conical gain horns with a rectangular waveguide interface can only support linear polarization, models with a circular waveguide interface can support various polarization types including horizontal, vertical, left-handed circular, and right-handed circular polarization for broader applications. The listed models operate across the full waveguide band and offer 23 dB nominal gain, 12 degrees typical half power beamwidth, a 24 dB typical side lobe level and 1.15:1 VSWR at center frequency. The below standard offering covers the frequency range of 8.5 to 140 GHz. However, other frequencies and standard models with 10, 15, 20 and 25 dB gain are also available.
-
Product
10 dB V-Band Waveguide Directional Coupler for Test Labs
SWD-5038531040H-15-SB
-
ModelSWD-5038531040H-15-SB is a V band, three-port waveguide directional coupler that delivers a 10 dB nominal coupling level and 30dB minimum directivity across the full waveguide band from 50to 85GHz. The three-port coupler uses a traditional multi-holeand split block design to achieve a flat coupling level, high directivity, and low insertion loss. The interfaces of the coupler are WR-15waveguides with UG-385/Uflanges. Custom coupling levels are available under different model numbers.
-
-
-
-
Product
Waveguide Adapter
-
RF Lambda’s waveguide adapter product line is used to convert a waveguide interface to a coaxial interface. They come in a variety of frequencies, connector options and materials. They offer low insertion loss and VSWR as well as high power handling.
-
Product
Mechanical Calibration Kit, 12.4 To 18.0 GHz, Waveguide, WR-62
P11644A
-
The Keysight P11644A calibration kit contains the precision mechanical standards required to calibrate the systematic errors of Keysight network analyzers. This calibration kit has a precision airline for performing the thru-reflect-line (TRL) calibration, the most accurate error-correction technique for coaxial measurements. This kit also contains a commercial calibration certificate, flush short circuit, a precision shim, and fixed termination(s).
-
-
Product
Gunn Oscillators
-
Gunn Oscillators are solid state microwave energy generators. These consists of waveguide cavity flanged on one end and micrometer driven plunger fitted on the other end. A gunn-doid is mounted inside the waveguide with BNC Connector for D.C. Bias.
-
Product
Manual Attenuator (Waveguide)
-
Manual control waveguide attenuators in both variable (continuous) or stepped in a variety of frequencies, attenuation values / step sizes and power levels
-
Product
Millimeter Wave Amplifiers
-
Ducommun offers Low Noise (ALN), High Power (AHP), Full Waveguide Band (AFB) and General Purpose (AGP) amplifiers to cover the frequency range from 18 to 96 GHz. These amplifiers utilize thin-film and microelectronics manufacturing techniques and are discrete and/or MMIC PHEMT devices based. These amplifiers feature low noise, high output power, single DC power supply and wide operation temperature range. The amplifiers are offered in two categories, standard and custom-built. Both standard and custom-built amplifiers are equipped with various RF interface, including standard waveguide or coaxial connector for convenient system integration. The optional input and output integrated isolators are available as an option to further improve the port return loss.
-
Product
Double Ridged Waveguide Horn
DRH30
-
Frequency range: 2.5GHz - 30 GHz VSWR (max): < 1.55:1Impedance: 50 O (Ohm)Connector: K female Power (CW / Peak): 25W / 50 W
