Monitors
Continually examine for quality.
-
Product
Computrac® MAX®
4000XL
-
The Computrac MAX® 4000XL provides quick, reliable and accurate results. This improves the ability to adjust or monitor processes, ensuring quality products while minimizing waste, energy requirements and man-hours. Ease of use and durability, along with superior service and support make the Computrac® MAX® 4000XL an ideal choice for research, manufacturing and laboratory environments.
-
Product
Logger with Current Clamp0 to 200A AC
TV-4810
-
As well as recording data the unit has a display that shows what the unit is currently reading. The unit has an IP65 case and features high reading resolution and accuracy, a large memory, a fast offload speed and a low battery monitor.
-
Product
Flow Monitor
Deltaflow 180
-
The DeltaFlow® 180, measures volumetric flow from smoke stacks or pipes for process and compliance applications; it is a complete flow monitoring solution with easy installation in all applications including those with elevated temperature, particulate loading and corrosive gas concentration.
-
Product
USB-8501, 2-Port, Low-Speed/Fault Tolerant, USB CAN Interface Device
786307-01
CAN Interface
The USB-8501 is a low-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8501 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8501 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Automatic Engine Balancing Technology
AutoBalance™ System
-
Continuously adjusts fuel flow to each power cylinder to maintain balanced operationMinimize emissions and fuel consumption over a wide range of operating loadsReduce mechanical wear and maintenance costsReduce personnel costs and risk by eliminating manual engine balancingSupports engines with up to 20 power cylindersOn-Guard Diagnostic software for monitoring, analysis, reporting and trendingSupports automated air manifold pressure control for minimum emissions at varying loads
-
Product
Signal Conditioners
-
Omega's modular signal conditioners provide a low-cost, high-performance method of inter-connecting real-world analog signals with data acquisition, monitoring, or control systems.
-
Product
Remote/Local Broadcast Quality Assurance
AlertCenter
-
AlertCenter allows you to monitor one or more remote capture locations, recording multiple channels at each location. You can monitor and manage them from afar, using a single, centralized user interface, greatly cutting manpower and operational costs involved in having a monitoring operation on every site.
-
Product
Chlorine Dioxide Analyzer
-
optek’s chlorine dioxide (ClO2) analyzers are inline devices designed to measure real time ClO2 solution strength and/or ClO2 gas concentration . These analyzers can be designed to accommodate virtually any measuring range regardless of the stream’s phase. Operationally, the analyzer passes a white light beam through the ClO2 stream to be monitored, where light absorbance is measured at two distinct wavelengths.
-
Product
Signal Conditioners
SC-1300
-
The SC-1300 family of signal conditioners can convert the most commonly used process signals into conditioned current and voltage outputs, needed for control systems and monitoring devices. Dedicated functionality and isolation from control systems improves reliability.
-
Product
Electrostatic Products
-
We offer electrostatic measurement instruments for electrostatic discharge (ESD) and high-performance applications. Select from our reliable electrostatic sensors and detectors, voltmeters, charge plate monitors, and surface resistance/resistivity meters.
-
Product
Real-time Hardware Interfacing Package
VISUALCONNX
-
VISUALCONNX is a visualisation and control software product, allowing real-time hardware or software interfacing, monitoring and logging.
-
Product
Panel-mount Type Peracetic Acid Monitor
PM-960
-
A measurement device for continuous measurement of the concentration of peracetic acid used for sterilization in food and beverage processing. The device uses no reagents and is maintenance-free.
-
Product
Monitoring System
TriGas X5000
-
The TriGas X5000 Monitoring System is an integrated gas detection solution that helps plant operators comply with NFPA 820. The system monitors for combustible gases, hydrogen sulfide and oxygen with on-board alarming and communication interface to plant and remote location control stations.
-
Product
Oxygen Meters
-
A DATA HOLD button freezes the display to capture readings. Instrument recalls highest, lowest and average readings at the touch of a button. Computer output allows connection to a computer or data logger for monitoring and keeping results. Jumbo-size digits are 1-3/8 inches high
-
Product
ATEX-Compliant IR Temperature Sensors
FLIR A310 ex
-
Explosive atmospheres need to be protected from ignition sources. Selecting equipment and protective systems which meet the requirements of the ATEX Product Regulations or similar regulations is essential. FLIR A310 ex is an ATEX compliant solution, with a thermal imaging camera mounted in an enclosure, making it possible to monitor critical and other valuable assets also in explosive atmospheres. Typical applications for the A310 ex include process monitoring, quality control, and fire detection in explosive locations. Because the FLIR A310 ex is rated IP 67, it can be installed in dusty environments. The Flame-Proof Enclosure "d"prevents any explosion transmission from the inside of the enclosure to the outside.
-
Product
Versatile Sensor Network
-
Information System Technologies Inc.
ISTI offers a versatile, scalable and easy to use distributed sensor network solution for high fidelity data acquisition and development platform, allowing users/developers to test their signal processing and data fusion algorithms. The system supports multiple sensing types including acoustic, seismic and IR/scanning laser. Among the key capabilities of ISTI’s versatile sensor network are: (a) sensor-level hardware/software to provide configurable sampling and synchronization, on-board processing and storage for low to intermediate-level signal processing and data acquisition; (b) network-level solutions that account for network connectivity and sensor-network health monitoring and support various routing strategies; and (c) system-level console that allows users to select and upload application tasks. Users can choose several modes of operation to examine various factors such as reliability, bandwidth, and data timeliness.
-
Product
Personal Dose Alarm Meter
DP802i
-
DP802i type X - gamma radiation detector - as a super humanized design and enhanced personal dose monitoring is mainly used for X, gamma rays and hard beta rays of radiation protection monitoring, suitable for nuclear power station, the accelerator, isotope applications, industrial X, gamma NDT, radiation source treatment, medical treatment, cobalt gamma irradiation, radioactive laboratory, nuclear facilities around environmental monitoring field, timely, ensure to my warning safety of staff; The instrument can be also measured dose rate and cumulative dose. It USES reactive new single chip microcomputer, the compensation for the probe, the instrument GM counting pipe has a wide measurement range, better energy response characteristics, and with overload directives and protection function.
-
Product
SAFEONE® Pro Personal RF Safety Monitor
Pro SI-1100XT
-
SafeOne® Pro SI-1100XT is an effective and economical means to monitor the strength of electromagnetic (RF) fields from mobile phone towers, microwave ovens, radio and television installations, high frequency welders, and other common workplace RF sources between 10 and 18,000 MHz. The Personal RF Monitor is an important tool in complying with FCC, OSHA, and other safe workplace requirements.
-
Product
BACnet / Modbus
-
BACnet™ MS/TP and Modbus RTU communicating sensors provide an easy-to-install and cost-effective means to measure temperature and humidity anywhere on your network. They’re especially effective where there is limited controller inputs or the application is for monitoring only. All BACnet™ sensors are BTL Certified.
-
Product
Vehicle Presence and Data Collection Sensor
TrafiCam x-stream
-
TrafiCam x-stream combines a CMOS camera and video detector in one unit. TrafiCam x-stream sensors detect and monitor moving and stationary vehicles at signalized intersections and collect traffic data at intersections or interurban roads. Via detection outputs or via IP protocol, vehicle presence information is transmitted to the traffic controller so that signal timing can be adjusted dynamically. TrafiCam x-stream offers streaming video at full frame rate, to be used for traffic monitoring in a control room.
-
Product
Analyzers of batteries
-
LLC "Megaron" develops and manufactures instruments for measuring parameters of various chemical current sources, devices for testing batteries. This equipment of varying complexity, from simple, designed for a specific battery, with the possibility to universal computer monitoring processes.
-
Product
Laser Alignment
-
Laser beams are tracing a perfect straight propagating line. A special unique instrument was developed to monitor the direction and position of this laser beam, creating a cornerstone device for alignment. Typical applicationns are mechanical straightness and alignment, calibration articulated arms, accurate positioning, and many more. To facilitate unrestricted movement of the AlignMeter family a built-in wireless system was developed.
-
Product
Automotive Ethernet Interface Device
Ethernet Interface
The Automotive Ethernet Interface Device converts unshielded twisted pair (UTP) Automotive Ethernet to standard Ethernet. This device is ideal for developing applications that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). It includes ports for Automotive Ethernet connections and ports for 100BASE-TX Ethernet connections. You can use switches on the front panel to configure each 100BASE-T1 port as master or slave. The device also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
Product
Robust DIN-rail Fanless Embedded System With Intel® Atom™ Processor E3815 As An Intel® IoT Gateway Solution
ICO300-MI
-
The ICO300-MI based on Intel® Gateway Technology has been upgraded with Wind River Intelligent Device Platform XT v3.1. The reliable din-rail embedded IoT gateway platform utilizes the low power Intel® Atom™ processor E3815 and supports DDR3L system memory maximum up to 4GB, delivering high performance and low power consumption. It provides enterprise-grade security and intelligent manageability, yet simplifies the development process and gateway deployment for IoT applications. The intelligent ICO300-MI is a perfect solution for industrial IoT applications such as smart energy, smart factory automation, facility monitoring systems and more.
-
Product
Digital Microscopes
-
Digital microscopes are microscopes without eyepieces. A digital camera acts as a detector. Images are displayed on a screen or monitor, turning the microscopy workstation into an ergonomic digital workplace.
-
Product
Dust Monitoring
-
There are 100-times as many deaths in the workplace caused by the inhalation of dust as there are from all other workplace causes combined. Protecting your workers’ health and welfare is a serious responsibility. Take some of that weight from your shoulders with the world’s most advanced Personal Dust Monitors.
-
Product
Field-installation Type Residual Chlorine Meter (Four-Wire Transmission, Water flow beads)
HR-200
-
HR-200 is connected to a residual chlorine sensor (RA-20), which allows the free residual chlorine concentration to be measured with high accuracy. It is sutable for waterworks, pool water sterilization, and desalination systems. The measurement method is a three-pole polarographic method, which enables continuous monitoring of residual chlorine concentrations without using reagents. Stable measurement over a long period was realized by physical polishing cleaning using beads.
-
Product
Alarm SMS
-
Temperature & Humidity SMS Alert Controller can be utilized in monitoring the environmental condition for commercial, medical, food , storage, weather station, military, manufacturing industries. It makes use of SMS to alert users of temperature and humidity conditions via SMS. By implementing the bundled Server/Client Software and GSM modem, a management system of multi‐controllers can be built.
-
Product
Semiconductor Package Wind Tunnel
WT-100
-
Thermal Engineering Associates, Inc.
The WT-100 Forced Convection (Moving Air) Wind Tunnel is designed in accordance with the EIA/JEDEC JESD51-6 standard for thermal characterization of semiconductor packages and devices. The vertical design minimizes laboratory floor space requiements. Air is drawn in at the bottom and exhausts at the top. The test section is large enough to accommodate the largest JEDEC and SEMI thermal test boards. Air velocity can be adjusted over the range of 0.5 to 5 m/s; air velocity is monitored with an included hot-wire anemometer connected to a digital display. A Type-T thermocouple is mounted in the test section for monitoring the moving air temperature.
-
Product
Diesel Engine Tachometer
GE-1400
-
Handheld type digital engine tachometer to be designed for dedicated r/min measurement of 4-cycle diesel engines. R/min direct reading measurement is available only by clamping a CP-044 Diesel Engine Rotation Sensor (sold separately) to a fuel injection pipe.Both analog (switchable between analog and monitor output) and pulse outputs are provided; enabling to use analog output for data recording (monitor output for sensor waveform checking or analysis input signal of FFT analyzer), and to use pulse output for tracking analysis signal of FFT analyzer.
