Electricity
Columbs or amperes.
-
Product
PC Based Test Setup for Electric Iron Testing
-
SCR ELEKTRONIKS make PC Based Test Setup for Electric Iron Testing is useful to carry out various tests mentioned in IS 366:1991 clauses 10,11,12,13 & 14 on the Iron under test.
-
Product
Electric Motor Dynamometer
-
Dynamometer consists of aggressively designed rotor technology that allows for higher torque without the need for multiple rotors. Thus not only does the WB Series unit offer more pack to the punch, but the inertia of the WB Series unit stays well below the inertia of the engine being load-tested.
-
Product
Development Test for Electric Motors with Power Electronics
-
Test bench for electric machines and inverters in hybrid applications*Control of mechanical parameters*Verification of electrical properties*Checking the LL characteristics*Short circuit measurement*Recording the performance process*Noise measurement*Temperature measurement
-
Product
Multi Output Regulated DC Power Supply
LQ6324T
-
- Low cost general purpose laboratory bench unit.- Fully protected against overload and short circuit.- Three independent outputs electrically isolated from each other.- 5V/5A with over voltage crowbar protection for digital ICs.- Electrically floating outputs up to 500V DC w.r.t. ground.- Compact modular construction.- Precise regulation, low ripple and noise for both constant voltage and constant current operation.- Quality components and conservating ratings for high reliability and long life.
-
Product
FLIM Upgrades for Olympus
FV1000
-
*Two Fully Parallel TCSPC FLIM Channels*Compact bh Simple-Tau or Power-Tau System*Two HPM-100-40 GaAsP Hybrid Detectors*Optional: HPM-100-06 Hybrid Detectors, IRF Width < 20 ps FWHM*Optional: HPM-100-50 Hybrid Detectors for NIR FLIM*Optional: Multi-Wavelength FLIM*Excitation by bh ps Diode Lasers*Excellent Time Resolution: Electrical IRF Width 6.5 ps FWHM*Time Channel Width Down to 813 fs*Megapixel FLIM, Up to 2048 x 2048 Pixels at 256 Time Channels*Simultaneous FLIM/PLIM*Detection Wavelength Range from 360 nm to 900 nm*Excitation by Ti:Sa Laser, OPO, or by bh ps Diode Lasers*Systems for Multiphoton FLIM and Confocal FLIM*Systems are Modular: More FLIM Channels can be Added
-
Product
Electrical Calibration
GF6018A
-
Beijing GFUVE Electronics Co.,Ltd.
The equipment is compliance with national verification regulation: JJG1242005 "Ammeter, voltmeter, power meter and resistance meter verification rules" and related national standards. 0.05 single-phase AC/DC standard source, can verify magnitude 0.2 and the following AC/DC voltmeter, ammeter, frequency meter, resistance meter. The source signals by using DSP and 16-bit high-speed analog-to-digital converters of controllable sine wave, the distorted wave signal source.The equipment comes with RS-232 interface, can be connected with PC to a semi-automatic verification system. It has precise interface and multi-functions including verification, storage and query.The equipment adopts color LCD screen, chart character display is clear, with high precision, stable and reliable, convenient operation and flexible characteristics.
-
Product
Opto Electrical Slip Rings (Electrical and FORJ Combined)
-
Opto Electrical Slip Rings are a combination of fiber optic rotary joints (FORJ) with gold, silver or carbon contacts. High data rates are transmitted through the FORJ while power and other signals are transferred through a contact technology.
-
Product
Fault Finder for Electrical Wiring Open / Short Circuit
FF310
-
42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems. Operates on DC voltages from 6 to 42 volts. Internally protected against power surges and overloads. 8" flexible probe allows reaching wires in congested places. Transmitter and Receiver LEDs show open or short circuit conditions.
-
Product
Electrical Receptacle Tester
ERT100
-
UEi Test & Measurement Instruments
The ERT100 is a rugged, well-designed and well-built electrical receptacle tester. Featuring 6 different results with indicator lights for outlet condition, making it easy to read. With over molding and a comfortable grip, it fits comfortably into your hand. And is backed by a 1-Year limited warranty.
-
Product
Optical & Electrical Data/Pattern Generators
-
The Data/Pattern Generators offer both electrical and Optical outputs with standard and custom data patterns. PPG products cover data rates ranging from 100 Mb/s to 28.05 Gb/s.
-
Product
Electric Safety Wall Detection Test Mode
-
AllWin Instrument Science and Technology Co., Ltd.
Electric safety wall detecting functionTest mode programmableACW to IR function toggle automatically
-
Product
Multiphoton FLIM System
DCS-120 MP
-
*Multiphoton FLIM Upgrade for Existing Conventional Microscope*Two Fully Parallel TCSPC FLIM Channels*Compact bh Simple-Tau or Power-Tau System*Scanning by Fast Galvanometer Mirrors*Channel Seperation by Dichroic or Polarising Beamsplitters*Individually Selectable Pinholes and Filters*Excitation by Ti:Sa Laser*Two Non-Descanned Detection Channels*Two HPM-100-40 GaAsP Hybrid Detectors*Optional: Two HPM-100-06 Hybrid Detectors, IRF Width < 20 ps FWHM*Optional: HPM-100-50 Hybrid Detectors for NIR FLIM*Optional: Multi-Wavelength FLIM*Excellent Time Resolution: Electrical IRF Width 6.5 ps FWHM*Time Channel Width Down to 813 fs*Megapixel FLIM, Up to 2048 x 2048 Pixels at 256 Time Channels*Simultaneous FLIM/PLIM*Electronic Pinhole Alignment*Z-Stack FLIM Acquisition with Zeiss Axio Observer Z1*Optional: Spatial Mosaic FLIM via Motorized Sample Stage*Laser Control via SPCM Software
-
Product
Wet-Mateable Multi-Channel Electrical Connectors Rated for 1/1.7 (3.3) kV and 30 A
Nautilus WM1.7-30
-
Teledyne ODI's patented Nautilus is recognized as the leading choice for high reliability wet-mateable, multi-channel electrical connectors. Over 100,000 Nautilus connectors have been delivered for projects in diverse industries including oil and gas, oceanography, and defense.
-
Product
1-phase Power Analyzers
-
PeakTech Prüf- und Messtechnik GmbH
Is a high-precision energy cost measuring device for recording the energy consumption of electrical devices and for calculating the current consumption of a device by entering the electricity price. Thanks to the integrated power factor calculation, all modern consumers such as Switching power supplies, TV sets, fluorescent lamps, LED systems and of course ohmic loads such as Electric heaters and hobs can be measured accurately. In addition, the high resolution, the low response characteristic and even very small or stand-by consumers from approx. 1 W can be measured.
-
Product
Multifunctional Testers
-
Electrical installation safety is nowadays more important than ever with the proliferation of increasingly complex domestic electronic appliances people install in their homes that require reliable power supply lest they become damaged and pose a fire and electrocution risk. Effects of unreliable and even dangerous electrical installations are even more acutely felt in industrial environments where they translate into production losses.
-
Product
Component Test
-
Our innovative multi-function Electrical Component Testers have advanced functions such as voltage power control feed to activate components like radiator fan, headlights, horn, actuators, etc. and the sensor simulator can provide simulation of voltage signals, frequencies, square waves & duty signals with varying intensity to test the feasibility of good sensor signals in comparison to bad ones when troubleshooting vehicle electrical faults.
-
Product
Humidity Measurement
-
Martindale Electric Humidity Measurement - hygro-anemometer, hygro-moisture meter
-
-
Product
Voltage, Continuity & Current Tester
T5-1000
-
Measure current up to 100 A without breaking the circuit with OpenJaw™ design. The T5-1000 Electrical Tester is a versatile troubleshooting tool to carry to every job site. Use it to check voltage, continuity, and current–all with one compact tool.
-
Product
Industrial & 3-Phase Socket Testers
-
Martindale Electric Industrial & 3-Phase Socket Testers
-
Product
Production Test Stands for Electric Motors
-
Electric drives such as DC and EC motors are more and more extensively deployed in the automotive industry. At the same time there is an increasing requirement for a 100% analysis of motors for fault detection and error analysis as well as statistics on quality, without increasing production cycles times. The model-based Parameter Identification method (PI method) from imc allows testing to be performed under load, yet without an “explicit” separate load machine. Instead, the motor is loaded dynamically by exploiting its own inherent inertia. This allows motor parameters such as resistance, inductivity and friction to be determined within a few seconds. A mathematical model and its parameters reflect motor behaviour in its completeness and make it possible to monitor motor production based on limit values and trend statistics. The identified parameters of the model equation can then be used to calculate derived key performance indicators of the motor characteristic curve.
-
Product
Standard Tests
-
The following list contains only the most important standards and does not claim to be complete.EN 60204-1 Electrical equipment of machinesEN 60335-1 Electrical appliances for household and similar useEN 50106 Sampling test, routine tests (in conjunction with EN 60335-1)EN 60598-1 LuminariesEN 60601-1 Medical electrical equipmentEN 60730-1 Automatic electrical controlsEN 61010-1 Measuring, control and laboratory equipmentEN 61439-1 Switch cabinet and switchgearEN 62368-1 Equipment for audio/video, information and communication technologyEN 62841-1 Hand-held electric toolsEN 50191 Erection and operation of stationary and non-stationary electrical test equipmentLVD Low V oltage D irective _
-
Product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
-
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
Product
PXI Digital I/O And Prototyping Modules
Prototyping Module
Programmable Input Threshold and High-Side or Low-Side Drive Capability Available on Some ModulesOptically Isolated Input/Output for Interfacing to Electrically Noisy Environments Available on Some ModulesTTL Inputs and Outputs Suitable for Interfacing to External LogicOpen Collector/Drain Transistor Output Versions Suitable for Driving Internal or External Relay Coils
-
Product
Electrical Safety Multi-Analyzer
TOS9300 Series
-
The TOS9300 series is a high performance electrical safety analyzer that complies to a wide range of universal standards. Hipot, Insulation Resistance, Ground Bond, Leakage Current (touch current and protective conductor current) and partial discharge can all be tested. A total of 6 models are available for standard compliance tests in a wide variety of applications including R&D, quality assurance manufacturing lines and laboratory tests.
-
Product
Electric Attitude Gyroscopes
5000EG-series
-
The 5000EG gyro is based on our air-driven 5000B model, whose proven reliability has made it the industry standard for many years. There are two models available: 14 and 28 VDC. The rotor is precisely machined from a heavy-metal tungsten alloy, which has a higher mass than brass, contributing to the instrument’s demonstrated stability. The electric motor is driven by a built-in power inverter, and has an integrated air-erection mechanism. A warning flag is deployed upon loss of primary power. During acrobatic flights or short stops, the gyro’s mechanism can be caged whenever the knob is pulled.
-
Product
Electrical Development & Redesign
-
Your product description goes hereARC’s electrical engineering team has the leg up when it comes to developing or redesigning to your specific requirements.All the way from prototyping to cable design to integration, our talented team of clever engineers can deveop a prototype quickly and get your project off on the right foot. Whether it is a new solution or if you are redesigning an obsolescent FPGA system, our team can provide quickly and effectively while still keeping your budget in mind.
-
Product
6-Channel VME Optical-to-Electrical Converter
V730
-
The V730 is a six-channel logic-level optical-to-electrical converter, packaged as a single-width, 6U VME module. When used with compatible Highland optical transmitter modules, the V730 provides fast, low-jitter, EMI-proof distribution of pulses, triggers, and precision timing signals.
-
Product
Proximity sensors
-
Voltage 0...250V DC, 230 V AC Cable length 0.3, 2.5, 5, 7.5, 0.2...10 m Plug connection M8, M12 / female thread M5 Electrical Via reed contact Contactless PNP, NPN Pneumatic.
-
Product
Electrical Laboratory
-
As one of North America’s largest and most diversified product testing and engineering service providers, Trialon provides a comprehensive range of EMI/EMC, ESD and Electrical testing solutions. Our EMC Testing Laboratory is ISO/IEC 17025 accredited, as well as being an approved facility for both General Motors and Ford Motor Company. Plus, we provide multi-shift support to assure programs meet time lines. Trialon’s EMC team has NARTE-certified personnel that will provide you with reliable and cost-effective testing that complies with a wide range of industry standards.
