JTAG Emulators
Exercise a processor's (DUT) on-chip debug services to perform JTAG emulation and debug.
See Also: JTAG, JTAG Controllers, JTAG Debuggers, iJTAG, P1687
-
-
Product
Ethernet Cable Emulator
-
Upon different commands, it can simulate different network cable lengths, including 3 Modes: Bypass, Short, 100M. It can be used independently or jointly with other devices.
-
Product
In-Circuit Emulator
DS-251
-
# Real-Time and Transparent In-Circuit Emulator for 251s# Uses Intel and Atmel Licensed Bondout Technology# Standard 256K Emulation Memory# Real-Time Trace up to 128K Frames Deep, 128 Bits Wide# Complex Hardware Breakpoints# Supports Both Binary Mode and Source Mode# MS-Windows Debugger# High-Level Support for Popular C-Compilers# Full Support of Local and Global Variables# On-Line Assembler and Disassembler# Performance Analyzer
-
Product
Testing Solution & Battery Emulation
PLUTON
-
The PLUTON solution is a programmable DC power supply designed to function as a source or a regenerative charge.
-
Product
Channel Emulator
-
Qosmotec Software Solutions GmbH
Knowledge about channel models is not necessary to run tests with the QPER Channel Emulator. It applies the visualised virtual drive test concept, which is also used in the handover tester, to a fully fledged channel emulator: The tester outlines the network layout on the screen and defines a drive test route on the map. While running a simulated drive test, all channel effects are automatically calculated by QPER and applied to the channel emulation hardware.
-
Product
Network Emulation System
Mini Maxwell
-
Mini Maxwell -- Easy to use, portable, network emulator. Mini Maxwell''''s low cost of $1995 can fit into any testing budget. The Mini Maxwell is great if you have low power requirements, or need ultra quiet operation. Mini Maxwell supports packet drop/loss, duplication, delay (latency)/jitter, reorder, and burst. Includes: processor, memory, and three Ethernet interfaces in one enclosure with separate power supply, Linux OS, Mini Maxwell network emulator engine, graphical user interface, and 90 Day Warranty.
-
Product
Mobile Network Emulator
-
Qosmotec Software Solutions GmbH
QPER Mobile Network Emulator enables engineers to simulate handover scenarios in mobile networks without a fully-fledged test lab. Based on Qosmotec’s QPER technology, it allows to test UE and SIM-Card behaviour in a completely emulated mobile network: Cells can be configured with all relevant cell parameters (MCC, MNC, LAC, CI, etc.), SIMs can be added to the HLR, and UEs can use standard circuit switched and packed switched services. Thus, the QPER Mobile Network Emulator emulates the all components of a mobile network – consisting of core and radio functionality – and creates RF signals. It supports GSM, GPRS and EDGE (900 MHz, 1800 MHz) as well as UMTS (2100 MHz).
-
Product
JTAG External Modules for Cluster Test
JEMIO
-
The JTAG External Modules JEMIO™ for Cluster test are intended to provide test access to off-board signals that otherwise could not be accessed by a JTAG test system. For many designs, Boundary-Scan has adequate access to on-board signals, but signals that go off the board often cannot be tested by a JTAG tester. By adding JTAG access to these off-board signals, JEMIO™ modules can increase the board's JTAG test coverage, possibly reducing the need for implementing another test method or for developing alternative tests to reach the required level of test coverage.
-
Product
JTAG Software
-
Looking for flash programming or JTAG test utilities, we have them. Our software ranges from basic command line utilities to applications that extend the emulator's use in the field or the lab.
-
Product
Software And Hardware Battery Emulation Bundle
E36731ABV
-
The Keysight E36731ABV battery emulation bundle is a complete software and hardware solution for performing battery profiling and emulation, current drain analysis, and battery run-down and cycle testing.
-
Product
ROM Emulator Instrumentation
-
High-speed and static 3U and 6U PXI and PCI digital I/O instrumentation. Offering test rates to 200 MHz and programmable logic levels of -10 V to +15 V, our digital products feature the highest performance and most cost effective digital test solutions in the industry.
-
Product
Emulator
GCI E84
-
The GCI E84 Emulator is the world's leading tester for development, implementation and qualification of products that must comply with the SEMI E84 Standard. It provides the industry-standard automated test plans that are utilized by virtually every 300mm FAB and equipment manufacturer worldwide. GCI testers are the only solutions that guarantee 300mm factory automation interoperability.
-
Product
JTAG Boundary-Scan Hardware
-
JTAG Boundary-Scan Hardware by Corelis, including boundary-scan controllers, 12C serial bus protocol analyzers & exercisers, JTAG boundary Scan Modules, high-volume production JTAG systems, 7 support for 3rd party JTAG controllers
-
Product
Emulate Test in simulation
STIL-VT
-
Emulate test patterns in simulation environment with DUT simulation model. The simulation allows pre-silicon debug of test patterns. Reads the intermediate STIL format of tester patterns and creates a Verilog /VHDL simulation test bench. (A sub-set of Virtual tester solution)
-
Product
Emulates Atmel T89C51RD2 in 68-PLCC package
FE-51RD2\68P
-
* Emulates Atmel T89C51RD2 in 68-PLCC package * 60K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V, 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
Product
Accessories: Intermittent Fault Emulator
-
The Intermittent Fault Emulator (IFE) is the solution. The IFE enables manufacturers, suppliers and operators of any Intermittent Fault Detection (IFD) tester to demonstrate and verify its capabilities to detect and isolate intermittent faults.
-
Product
Live PD Emulation
-
Flexibly Mimic Class 0 to 4 Powered Device Per PSA/PSL-3000 Test Port. Configure up to 192 Simultaneous IEEE 802.3 PD’s. User-Defined Class 0 - 4 Powered Device Modeling with or without Cable Loss. Emulate 802.3at PoE-LLDP Negotiations and Power Adjustments. Monitor Multi-Port Live Emulation Status. Available to PSA-3000 and PSL-3000 Platforms as optional license feature.
-
Product
Network Emulator Software
NetDisturb
-
NetDisturb allows disturbing flows over IP networks helping to study the behavior of applications, devices or services in a “disturbed” network environment. NetDisturb is inserted between two Ethernet segments acting as a bridge and operates bi-directional packet transfer on Ethernet, Fast Ethernet and Gigabit network interface cards.
-
Product
JTAG Boundary-Scan Toolkit Software & Hardware Bundle
JTAG Starter Kit
-
The Corelis JTAG Starter Kit includes the ScanExpress Debugger software application with a USB 2.0 JTAG controller. Engineers and technicians alike can use the system for a variety of tasks. The JTAG Starter Kit has an arsenal of features to control and observe system signals of a boundary scan compatible UUT.
-
Product
Low Cost Emulator
EB-ST62
-
# Supports Most of the ST62 Microcontrollers# Real-Time Emulation up to Device Frequency# 3.3V and 5V Operating Voltages# Real-Time Trace Buffer# Source-Level Debugger for C and Assembler# Unlimited Number of Breakpoints# Stack Overflow Debug Breakpoints# 8K Bytes Emulation ROM# 192 Bytes Emulation RAM# 128 Bytes Emulation EEPROM# On-Board Switches and LEDs
-
Product
Battery Emulator And Profiler
E36731A
Battery Simulator
The Keysight E36731A battery emulator and profiler is an integrated electronic load and power supply developed to use with Keysight PathWave BenchVue battery emulation software. An emulated battery gives you a known good reference for testing at any charge level. Quickly assess the effect of design or software changes on battery life by emulating any battery charge state. Leverage emulation and precise current drain analysis to achieve longer battery life or to reduce the size of your device.
-
Product
10M/100M/1G Ethernet Network Emulator
VirtualNetTM GE
-
VirtualNet-1G is a high-performance Network Emulator that replicates real world Ethernet network effects such as latency and errors on user traffic in a controlled environment. The VirtualNet-1G emulator uses customized ICs to support full line rate performance at all frame sizes and impairment settings. The emulator can be transparently installed in-line as shown in the diagram below. VirtualNet-1G emulator has an intuitive and easy to use GUI interface and a very powerful TCL based CLI to aid in configuration and testing.
-
Product
JESD22-A115 Machine-Model (MM) Pulse Emulator
MM-10A
-
High Power Pulse Instruments GmbH
- Pulse unit to generate JESD22-A115 machine-model (MM) waveforms with TLP- Extremely stable and reproducible machine-model (MM) waveforms- Compatible with HPPI TLP-3010C/4010C/8010A/8010Csystems which have installed pulse width of 25 ns and rise time of 100 ps to 300 ps- Up to ±10 A machine-model peak current with TLP-3010C, which is equivalent to ±667 V (MM)- Up to ±15 A machine-model peak current with TLP-4010C, which is equivalent to ±1000 V (MM)- Up to ±30 A machine-model peak current with TLP-8010A and TLP-8010C, which is equivalent to ±2000 V (MM)- Same measurement procedure as TLP including DC test of the DUT- Compatible with HPPI TLP software and waveform data storage and management- 50 Ω SMA input and output connectors- Compact size: 61 mm x 25 mm x 17 mm
-
Product
JTAG 3rd Party Controller Support
-
Corelis offers support for a variety of devices and instruments from third-parties in an effort to provide existing test platforms comprehensive JTAG test execution with Corelis ScanExpress software products. Supported instruments include National Instruments PXI-655x HSDIO and Teradyne Di-Series modules. Corelis also provides support for JTAG testing with FTDI FT2232 ICs embedded on a unit under test (UUT).
-
-
Product
WAN Emulators
Linktropy
-
Linktropy WAN emulators simulate a single link through each pair of interfaces, offering the simplest configuration possible. If you need to emulate a single set of conditions between two networks, Linktropy is the product for you.
-
Product
Handover Emulator
-
Qosmotec Software Solutions GmbH
The Qosmotec handover test system QPER is a versatile test platform for emulating the RF signal between radio devices in a wireless network, e.g., between mobile stations and radio infrastructure of a mobile network. It is employed in test beds where radio signals are transmitted through coaxial cables and specifically manipulated by testers. QPER can be based on various hardware platforms, from attenuator arrays to digital channel emulators.
-
Product
Mobile Comm DC Source w/ Battery Emulation
66321B
Battery Simulator
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66321B mobile communications dc source provides fast transient response, exceptional sourcing, output resistance programming, and precision measurement. This product is specially designed for testing next generation digital wireless communications products. The 66321B mobile communications dc source offers a new capability that simulates the internal resistance of a battery or battery pack. Additionally, these high performance models offer improved transient response and stable output operation with either short or long load leads.
-
Product
Network Emulator and Protocol Tester
Maxwell Pro
-
The Maxwell Pro Network Emulator helps engineers learn how their products will perform in mobile, cloud, and WAN networks. By capturing and changing network flows, Maxwell Pro can induce the conditions that cause network congestion, slow links, time outs, Lossy networks (LLNs), and many other adverse network conditions. Engineers can then see the effects on the device or application to find and fix bugs, solve network problems, and learn the limits of device and application performance.
-
Product
In-Circuit Emulator
DS-51
-
* Real-Time and Transparent In-Circuit Emulator * Supports Most of the 8051 Derivatives * Emulates 1.5V to 6V Microcontrollers * Maximum Frequency of 42MHz * 64K/512K of Internal Memory with Banking Support * 32K Trace Memory "on the Fly" * 64K Hardware and Conditional Breakpoints * MS-Windows and Keil ?Vision Debuggers * Source-Level Debugger for Assembler, PLM and C * On-Line Assembler and Disassembler * Performance Analyzer * Serially linked to IBM PC at 115 Kbaud
