-
Product
SparkFun Mini Breakout
SAMD21
-
If you’re ready to step your Arduino game up from older 8-bit/16MHz microcontrollers, the SparkFun SAMD21 Mini Breakout is a great landing spot. The SAMD21 Mini Breakout is a Pro Mini-sized breakout for the Atmel ATSAMD21G18, a 32-bit ARM Cortex-M0+ processor with 256KB flash, 32KB SRAM, and an operating speed of up to 48MHz. This mini breakout provides you with an Arduino hardware option that solves the problems of low storage limits and dynamic memory stack overflows that have plagued the previous iterations of the Arduino family. Yes, the SparkFun SAMD21 Mini Breakout is even fully supported in the Arduino IDE and libraries for the Arduino Zero!
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Development System
FE-SND2
-
* Emulates Atmel AT89C51SND2 Microcontrollers * 62K Code Memory * Real-Time Emulation * Frequency up to fmax * ISP and X2 Mode Support * Windows Debugger For C, C++ and Assembler * USB or RS-232 Linked to PC * C Compiler and Assembler
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Evaluation Kits:
Grid-EYE® AMG8834EVAL Evaluation Kit
-
Panasonic Industrial Devices Sales Company of America
Panasonic is pleased to announce the availability of the Grid-EYE AMG8834EVAL Evaluation Kit featuring TrackMe Software for its' Grid-EYE Infrared Array Sensor, which integrates a ”nanopower” Bluetooth® Smart Module and a microcontroller. The AMG8834EVAL Kit is intended for prototyping the Grid-EYE Sensor which is a 64 pixel IR camera in a surface mount package measuring 11.6mm x 8mm x 4.3mm, which integrates the MEMS Sensor, lens and I2C interface.
-
Product
Pro Micro
5V/16MHz
-
Here at SparkFun, we refuse to leave 'good enough' alone. That's why we're adding to our line-up of Arduino-compatible microcontrollers once more! The Pro Micro is similar to the Pro Mini except with an ATmega32U4 on board. The USB transceiver inside the 32U4 allows us to add USB connectivity on-board and do away with bulky external USB interface.
-
Product
Profiling and Coverage Analyzer Tool
Analyzer
-
One of the most effective debugging techniques in embedded development and testing is tracing. Tracing means recording microcontroller activity, such as Program or Data flow.
-
Product
Microcontrollers
-
Microcontrollers by IXYS - Microcontrollers, Detection & Control, Motor Control, and more.
-
Product
ST10 16-bit Automotive MCUs
-
ST's ST10 microcontroller family offers a wide range of devices for use in automotive applications. The family integrates scalable single-voltage embedded Flash, from 128 to 832 Kbytes. Processed in 0.18 µm CMOS technology, it offers full 5 V capability and an internal on-chip voltage regulator.
-
Product
Energy Meter
-
Nippen Electrical Instruments Co.
DIGITAL METERS NIPPEN electronic energy meters are panel mounting type innovative energy monitoring devices ,having state of the art electronic microcontroller circuitry for reliability and accuracy. They can be used for 1Ø / 3Ø balanced and unbalanced loads.
-
Product
300-Watt AC/DC Power Supply, 6U VME
Model 56SQ2
-
NAI’s 56SQ2 is a 300 Watt AC/DC Power Supply that uses two slots in a standard VME chassis. It is conduction-cooled through the card edge/wedgelock. This power supply accepts either a single- or three-phase input and provides up to 5 standard VME outputs plus standby at 300 Watts. It is designed for VME and general purpose applications. An onboard microcontroller allows for design flexibility.Standard features include continuous Background Built-in-Test (BIT); remote error sensing; holdup time; and protection against transients, overvoltage and short circuits. Options such as power fail warning, vibration testing, over-temperature monitoring and shutdown, current share, and extensive signaling (including ANSI/VITA) are available.
-
Product
Dynatrol® Digital Viscosity Converters
Series 3000
-
Dynatrol® Series 3000 Digital Viscosity Converters were designed for use with all Dynatrol® Viscosity Systems. Using microcontroller technology, the digital converter accepts information from a Dynatrol® Viscosity Probe and calculates the viscosity of the liquid under test. The Series 3000 converter mathematically computes and displays the viscosity in standard units.
-
Product
RL78 Family Of 8/16-bit Ultra-Low Energy MCUs
RL78/F1x
-
The RL78/F1x microcontrollers are suitable for automotive applications. As the successors of both the 78K0R and R8C, they realize low power consumption and are equipped with built-in functions suitable for automotive applications such as CAN communications, advanced timer, and safety functions.
-
Product
Cross Development Tools
68HC12 and HCS12
-
Cosmic's toolchain for the 68HC12/HCS12 family is part of a complete and uniform product line incorporating over 20 years of innovative design and development. Cosmic's familiar and easy to use software interface is available for all Freescale microcontrollers to simplify the migration between targets. All Cosmic products include one year of technical support and updates.
-
Product
MCB Endurance Test Bench
-
The SCR Elektroniks Endurance Test Bench is designed for electrical and mechanical endurance MCB and RCCB as per clause 9.11 of IEC 60898-1. The source and the load is designed to comply as per the general test conditions specified in Cl 9.11.1. The accompanying pneumatic fixture is designed to hold custom built designs of MCB and RCCB while the microcontroller based timer unit can be configure to follow test procedure summarized in Cl 9.11.2.
-
Product
Linux-based Development Platform For The GridARM™ ΜController
PEAK gridARM Evaluation Board
-
The ARM7 microcontroller gridARM™ was developed by Grid Connect® as a system on a chip solution (SoC) for the implementation of embedded applications with a focus on industrial communication. The Evaluation Board PEAK-gridARM is a Linux-based development platform for the gridARM™ microcontroller. It has connections for Gigabit Ethernet, high-speed CAN, USB 2.0, RS-232, SPI and I²C. The digital and analog inputs of the evaluation board can be manipulated with buttons and potentiometers. The states of the microcontroller, the supply and the message traffic are displayed via LEDs. A board support package for Linux enables access to the hardware resources of the PEAK-gridARM evaluation board.
-
Product
Air-Cooled Universal Test Platform
Diamondx
-
Diamondx semiconductor test system extends Cohu’s low-cost, high-throughput production test solution platforms to high pin count, higher site count wireless, mobility, SOC, Flat Panel Display drivers, Power Management, and microcontrollers. Designed to meet the cost drivers IC companies face, Diamondx extends Cohu’s leadership in lowering the cost of operations.
-
Product
Smartcard Interfaces
-
ST offers complete analog interfaces for asynchronous 1.8 V, 3 V and 5 V smartcards. They can be placed between the card and the microcontroller with only a few external components to perform all supply protection and control functions. Main targeted applications are smartcard readers for set-top boxes, IC card readers for banking, identification and pay TV.
-
Product
Software And Tools
-
Renesas Electronics offers high-quality software, high-function and easy-to-use development tools, an abundant boards & kits lineup for development environment for Renesas microcontrollers and microprocessors. This fully designed development environment helps you develop your system more effectively and efficiently; reduces your development time and cost yet improves the quality of system. Furthermore, we offer various third party products and they will also enable you to have development environment best fit to your needs.
-
Product
I2C Protocol Analyzer
EasyI2C
-
It's simple to find an I2C-style bus within arm's reach. Every computer, monitor, television and cell phone has it. Most microcontrollers directly support this protocol as well. Even so, the I2C protocol has many subtle nuances that are hard to grasp and easily forgotten. EasyI2C (TM) helps you to figure out exactly what is happening, without having to examine huge waveform trace capture files or set up complex tests.
-
Product
SparkFun Opto-isolator Breakout
-
This is a board designed for opto-isolation. This board is helpful for connecting digital systems (like a 5V microcontroller) to a high-voltage or noisy system. This board electrically isolates a controller from the high-power system by use of an opto-isolator IC. This IC has two LEDs and two photodiodes built-in. This allows the low-voltage side to control a high voltage side.
-
Product
ICT Programmer
-
Compatible with a wide range of microcontrollers in electronic devices. Supports programming of single product or bulk PCBA boards. Enables quick replacement of the adapter or dedicated product inserts. Equipped with a high-performance, multi-channel industrial ISP programmer.
-
Product
Development System
FE-900
-
# Emulates Philips P89LPC932 Microcontrollers# Real-Time and Transparent Emulation up to 12MHz# 8K Emulation Memory# Real-Time Trace# Uses Philips Bond-Out Technology# Ceibo Windows Debugger and Keil uVision2# High-Level Support for all C/C++ Compilers and Assemblers# On-Line Assembler and Disassembler# Target Board, ISP Programmer and Power Supply Included# PLCC-28 Emulator Plug Included (TSSOP-28 Optional)
-
Product
Accelerometers
-
The unit is based on micro machined MEMS technology. The unit contains a 35g sensing element. The element is scaled to optimise the resolution to suit the g range of interest. An internal amplifier provides an output between 0 and 5 volts. The on board microcontroller and temperature sensor are used for offset drift compensation. This unit can be re-calibrated at the factory.
-
Product
Microprocessor Development System
DS-48
-
# Real-Time and Transparent In-Circuit Emulator# Supports Philips Telecom Derivatives# Adaptable to 8051 Derivatives# Emulates 1.5V to 6V Microcontrollers# Maximum Frequency of 40MHz# 8K of Internal Memory# DOS and MS-Windows Debuggers# 32K Trace Memory and Logic Analyzer "on the Fly"# 8K Hardware and Conditional Breakpoints
-
Product
Development System
FE-51MX
-
* Emulates Philips P8xC51MA/B/C , P89C669 Microcontrollers * 1MByte Code Memory * Based on bond-out Technology * Frequency up to 24MHz 3V / 5V Operation * Huge Real Time Trace Memory * Windows Debugger for C/C++ and Assembler * Target Board Included * RS-232 or USB Interface * 64K C/ASM and 8K C++ Included
-
Product
Code Optimizing C Compilers for Microchip PIC® and dsPIC® DSCs
-
CCS developed the first C Compiler for Microchip microcontrollers over 20 years ago and continues to provide software solutions to developers of embedded applications using PIC® MCU and PIC24/dsPIC® DSC devices. CCS compilers are easy to use and quick to learn. For the less experienced programmer, a detailed textbook explaining the C language and how it may be applied to PIC® microcontrollers.
-
Product
Linear Equalizers
-
Macom Technology Solutions Holdings Inc.
MACOM offers high-performance linear equalizers for use in high speed copper connections for Ethernet, InfiniBand and Fibre Channel. The product line supports NRZ and PAM-4 multi-level signal connectivity and builds upon MACOM’s long-standing expertise in equalizers for broadcast video applications. The equalizers can support up to 112Gbps per lane data rates for 50 Gbps to 800 Gbps copper cable assemblies. In addition to copper cables, the linear equalizer can be used for wired backplane and on-board applications. Adding linear equalization to a passive copper cable can enable the same copper cable to carry higher data rates for longer distances. MACOM’s new linear equalizer product line can extend a typical copper cable’s performance to 7.5 meters at 56 Gbps and 5 meters at 112 Gbps data rates. Customers can consider active copper cables as an alternative to passive copper cables or active optical cables. Key benefits include low power consumption from a single 3.3V supply, low latency, hardware and microcontroller management modes. The products are suitable for SFP, QSFP, QSFP-DD and OSFP connector form factors.
-
Product
32-bit Microcontrollers (MCUs)
EFM32™
-
The energy-friendly EFM32 MCUs are ideal for ultra-low power applications. Based on ARM Cortex-M0+, Cortex-M3 and Cortex-M4 cores, EFM32 MCUs also include the most energy-friendly peripherals and energy modes to enable design of highly functional low power systems.
-
Product
Environment click
-
Environment click measures temperature, relative humidity, pressure and VOC (Volatile Organic compounds gases). The click carries the BME680 environmental sensor from Bosch. Environment click is designed to run on a 3.3V power supply. It communicates with the target microcontroller over SPI or I2C interface.
