PXI Carriers
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2Ω to 13.6kΩ
40-251-131
Programmable Resistor Modules
The 40-251-131 is a programmable resistor module with 2 channels which can be set between 2Ω and 13.6kΩ with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
8-CH 14-bit 100 MS/s High-Speed PXI Express Digitizer
PXIe-9848
Digitizer
The ADLINK PXIe-9848/9848H is an 8-channel, 14-bit, 100 MS/s digitizer delivering both high-accuracy measurement results and high-dynamic performance. With a PXI Express bus interface and ample onboard acquisition memory up to 512 MB, the PXIe-9848/9848H can easily manage simultaneous 8-CH data streaming. High density and high speed digitizer features ideally position the PXIe-9848/9848H for applications such as LIDAR, radar signal acquisition, and PSU (Power Supply Unit) testing applications.The PXIe-9848 provides a flexible set of input ranges from ±0.2V to ±2V, software selectable 50Ω or 1MΩ input impedance, a wide variety of triggering options and tight synchronization capability, all maximizing convenience of use. In addition, ADLINK provides the PXIe-9848H, features a x15/x50 signal condition module providing both high input voltage range of ±100V and high dynamic performance, delivering the optimum solution to measurement range expansion in a PXI system.
-
Product
PXI 8-Slot BRIC Matrix, 1104x4, 1-Pole (12 sub-cards)
40-560B-121-1104X4
Matrix Switch Module
The 40-560B-121-1104x4 is an ultra high density matrix module and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781339-04
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
PXI Prototyping Module, 1-Slot, Dual 20-Pin GMCT
40-225A-811
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
PXI 4 Slot BRIC 116x6 2A 1-Pole Matrix
40-596-002
Matrix Switch Module
The 40-596 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 150VDC/100VAC. The 40-596 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 16x2 RF Matrix 100MHz 75 SMB
40-728-101
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI Precision Resistor Module 9-Channel, 2 to 26.7k
40-297-032
Programmable Resistor Modules
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI To CPCI Or PXI Extender Board
MS 1720
-
PCI to CPCI Extender card is used for extending the standard desktop PCI bus to compatible CPCI bus. This will help to test all the CPCI and PXI cards without having a CPCI or PXI backplane. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the CPCI and PXI boards.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-342-HI
-
The 40-230-342-HI (PXI) and 42-230-342-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 392kΩ with 0.5Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI Expandable 16x16 RF Matrix 75Ohm SMB
45-720A-751
Matrix Switch Module
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
PXI 8-Slot BRIC Matrix, 99x16 2-Pole (9 sub-cards)
40-562B-122-99X16
Matrix Switch Module
The 40-562B-122-99X16 is a high density BRIC8 matrix module with a size of 99x16 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 8/16-Channel Isolated D/A Converter
M9185A
Digital / Analog Converter
The M9185A is a fully independent, isolated D/A converter that is capable of supplying high voltage levels in parallel of up to eight or sixteen channels. Each channel is able to output up to 16V as stimulus signals to Device Under Tests (DUTs).
-
Product
PXI 5A Power Multiplexer, 1-Bank, 48-Channel, Independent Isolation
40-651A-101
Multiplexer Module
The 40-651A-101 is part of our range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats.
-
Product
6U High-Density PXI RF Matrices
-
Pickering's 6U high-density matrices are suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high-performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture - this maximizes isolation and RF performance.
-
Product
PXI Very High Density Multiplexer, 49-Channel, 4-Pole
40-675A-002-49/4
Multiplexer Module
The 40-675A-002-49/4 is a 49-channel, 4-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
PCI Bus Carrier for IP Modules
APC8620A
-
This board interfaces industry-standard Industrial I/O Pack (IP) modules to a PCI bus on a PC-based computer system.
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 1.5Ω to 1.81kΩ
40-253-022
Programmable Resistor Modules
The 40-253-022 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 8 Slot BRIC 33x16 1-Pole (3 sub-cards)
40-562A-121-33X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 8 Slot BRIC 220x8 1-Pole (10 sub-cards)
40-562A-121-220X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Squid PCI Express Carrier Board™ for M.2 and NGSFF (NF1) SSD Modules
-
Amfeltec Squid PCI Express Carrier Board™ for M.2 and NGSFF (NF1) SSD Modules
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-115-HI
-
The 40-230-115-HI (PXI) and 42-230-115-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 2.5Ω and 925Ω with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI 4-Slot BRIC Matrix, 276x4, 1-Pole (3 sub-cards)
40-560B-021-276X4
Matrix Switch Module
The 40-560B-021-276x4 is an ultra high density matrix module and is part of our range PXI BRIC matrices. They are available in 2, 4, 8 or 12-slot sizes to suit high performance PXI switching requirements and is constructed using instrumentation quality reed relays.
-
Product
PCI Express Control of PXI Express
PCIe-PXIe-8638
Extension Kit
The PCIe-PXIe-8638 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signaling. With comprehensive hardware and software transparency, the expansion kit enables fast and convenient detection of any PXI cards installed in the system, requiring no additional drivers or software.
-
Product
PXI 12-Slot BRIC Matrix, 176x16 2-Pole (16 sub-cards)
40-562B-322-176X16
Matrix Switch Module
The 40-562B-322-176X16 is a high density BRIC12 matrix module with a size of 176x16 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Dual 2 Channel (M Mode) SC 62.5 Cons
40-855-222-M62.5
Switch Module
The fiber optic switches connect the common to a channelby redirecting the optical signal into a selected output fiber.This is achieved using Micro-Mechanical Mirrors driven bya highly precise mechanism and activated via an electricalcontrol signal.
-
Product
PXIe-8523, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module
787311-01
Ethernet Interface
PXIe, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8523 is a 100/1000BASE-T1 unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications … that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8523 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8523 also provides LEDs on the front panel to help you monitor the network link and activity.
-
Product
Carriers
-
VadaTech carriers are available in a wide range of mezzanine styles and formats, including versions to enable you to adapt different buses and architectures. These carriers are designed to enable you to build a complete system using best-in-class building blocks or legacy products regardless of the form factor.
-
Product
PXI 10A Fault Insertion Switch 10-Chan 1-Bus
40-199-001
Fault Insertion Unit
The 40-199 is a 10 Channel Fault Insertion switch designed for the simulation of fault conditions in automotive/avionics applications, involving the reliability testing of safety critical controllers.
-
Product
High Performance PXI Functional Test System with Mac Panel Interface
TS-5400
Functional Test
The Keysight TS-5400 PXI Series Functional Test System provides automotive, aerospace and defense and industrial control manufacturers with an off-the-shelf PXI hardware and software platform with support for single or multiple DUT test. Designed for testing electronics control modules such as, power train control, complex body electronics and industrial controllers, the TS-5400 PXI Series helps manufacturers achieve higher throughput for their design validation and manufacturing functional test needs with the capacity to empower them to anticipate future functional test needs.
