-
Product
Handheld Water Quality Meters
LAQUA PC210
-
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)- 0.01 pH resolution- Offset and average slope display- ORP calibration option- Automatic / manual temperature compensation and temperature calibration function- Automatic (up to 4 points) and manual (up to 5 points) conductivity calibration- Adjustable reference temperature and temperature coefficient- Adjustable cell constant and selectable measurement unit- Conductivity and total dissolved solids (TDS) conversion- Four (4) TDS calibration curves for wide range of applications: EN27888, Linear, 442, NaCl- Two (2) salinity calibration curves: NaCl, Seawater - Auto log data; built-in memory can store up to 500 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached - Monochrome LCD with white LED backlight: 50 x 50 mm- Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrodes and calibration solutions in carrying case- 3 years meter warranty
-
-
Product
PXI Resistor Module 2-Channel 1.5R to 2.04k
40-293-022
-
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Alert Receiver Software
SafAlert
-
SafAlert is an autonomous alert decoder triggered by any programmable single, dual, or sequential tone signal, such as EAS, NOAA, or 2-tone fire alarm page. User-programmable visual, audible and email alerting
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 16.3k Ohm With SPDT
50-293-131
-
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Hot Temperature Hardness Tester
1200C
-
Rtec high temperature hardness tester is used to do high temperature materials testing up to 1200C. To prevent oxidation of tip and the samples the high temperature indenter comes with sealed chamber with inert gas. High resolution programmable down force control and XY stage allows to do multiple indents on same or multiple samples with ease.
-
Product
Non Destructive Testing (NDT)
-
NDT covers a wide group of testing techniques used to evaluate the properties of a material, part, product, weld or system without causing damage. NDT carried out at KLL includes:Liquid Penetrant Testing (LPT) is used for the detection of surface breaking discontinuities on magnetic and non-magnetic metallic materials.Fluorescent and colour contrast penetrants are available to be used in the following methods:-Water washableSolvent removablePost emulsifiableMagnetic Particle Inspection (MT/MPI) is used for the detection of surface breaking and slightly sub-surface (up to 2mm) discontinuities.Bench type crack detectors and portable units are employed producing various waveforms (i.e. A.C, HWDC and induced magnetic flow) to give both circular and longitudinal magnetism.On-site testing is carried out using electro magnetic yokes and permanent magnets producing induced magnetic flow.Ultrasonic Flaw Detection (UT), also known as Ultrasonic Inspection, is used for the detection of volumetric discontinuities in ferrous and non-ferrous products (forgings and castings etc.), and welds in magnetic and non-magnetic materials.UT is capable of penetrating metals, dependent on the material characteristics, up to 10m in length.Some thickness and depth checks can also be carried out using ultrasound.Radiography services are available through sub-contract booked in advance. Notice is required for on-site work.Personnel are available at short notice for in-house or on-site work in the UK and overseas.All inspectors undertaking non destructive testing (LPT, MT/MPI and UT) are qualified to, and meet a minimum of, PCN Level 2.PCN Level 3 supervision is available in-house for LPT, MT/MPI, UT offering consultancy services including procedure writing and commentary, auditing of techniques and Level 3 Supervisor cover.We can assist clients in product qualification, material testing, quality assurance and audit programmes.
-
Product
Low Power Programmable AC Source
-
Chroma Systems Solutions, Inc.
Delivers pure, instrument grade AC power at very low cost with output voltage from 0 to 300VAC, and frequencies from 15 to 1000Hz
-
Product
Programmable Setpoint RelayProtection Relay, Trip Relay
CRD-005 and CRD-020
-
CRD-020 Programmable ac current set-point relay setting for threshold levels, over and under-currentoperationbulletCRD-005 Programmable dc voltage and mA set-point relay setting for threshold levels, over and under-voltage operationbulletCRD-005 internal DIP-switches allow for either 0-1mAdc or 0-10Vdc operation, and may be set for under-alarm or over-alarm relay operationbulletCRD-020 internal DIP-switch allow configuration of the ac current range to either 0-5A, 0-10A, 0-15A or 0-20A and the relay mode for under-current or over-current operationbulletLid mounted two digit numerical push button switch calibrated as percent of full scale with a threshold range of 1-99%bulletRed LED lamp lights to indicate when the threshold level has been tripped
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 1.51MΩ
50-298-150
-
The 50-298-150 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 1.51MΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Power Supplies and Sources
DC Power Supplies
-
DC power supplies are commonly used in electronics design, battery charging, electrical vehicle, research labs and education sectors. UNI-T offers both programmable and non-programmable power supplies with features such as low ripple and noise, constant voltage/current, overload protection, and more.
-
Product
Bench pH/Conductivity/TDS Meter
CyberScan PC 510
-
Multi-parameter meters measures pH, Conductivity and TDS in single meter User-Customization for more accurate measurements with programmable functions like stability, electrode diagnosis - pH slope/offset/mV base value, etc.
-
Product
Disintegration Testing
-
Agilent offers innovative dissolution testing systems to accurately measure the disintegration of dosage forms into particles under standard conditions. The Agilent 100 Automated Disintegration Apparatus is a fully programmable solution delivering reliable disintegration testing results. Our disintegration testing systems are compact and easy to manage, featuring precise temperature control and meeting regulatory compliance requirements.
-
Product
Dual Matched, High Frequency Bandpass/Lowpass Filters
LTC6602
-
The LTC6602 is a dual, matched, programmable bandpass or lowpass filter and differential driver. The selectivity of the LTC6602, combined with its phase matching and dynamic range, make it ideal for filtering in RFID systems. With two degree phase matching between channels, the LTC6602 can be used in applications requiring highly matched filters, such as transceiver I and Q channels. Gain programmability, and the fully differential inputs and outputs, simplify implementation in most systems.
-
Product
Programmable DC Power Supply
M88 series
-
M88 series power supply are high performance single-output programmable DC power supply with communication interface, possessing the character of fast rise speed (The rise time of M8811 power supply can be less than 10ms and that of M8851 can be less than 20ms). The combination of bench-top and system features in these power supply provides versatile solutions for your design and test requirements. The M88 series can not only be programmed through the keyboard on the panel, but also be functioned as voltmeter and milliohm meter, which will bring great convenience to the users. As a regeneration product of ordinary programmable power supply, M88 series power supply are more cost-effective.
-
Product
Small Step Frequency Synthesizer
ZFR Series
-
ZFR series programmable frequency synthesizers combine multi-octave bandwidth, small step size, low phase noise, fast switching speed, and a compact package size to create a truly versatile synthesizer. The ZFR series can be tailored to the specific frequency range and control interface required, with programmable frequencies to 31 GHz.
-
Product
Programmer Memories VP-598
-
Support more than 21 637+ memories . We are official distributor of Wellon products in Poland. Our customers receive 3 years warranty and 72h support.
-
Product
PXI 5W Programmable Resistor Module, 2-Channel, 2Ω to 52.4kΩ
40-252-033
-
The 40-252-033 is a programmable resistor module with 2 channels which can be set between 2Ω and 52.4kΩ with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 16.3k Ohm - SPST
50-294-131
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI High Density Precision Resistor Module, 6-Channel, 4Ω to 11.4MΩ
40-298-053
-
The 40-298-053 is a high density programmable resistor module with 6 channels which can be set between 4Ω and 11.4MΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 1.5Ω to 925Ω
40-251-121
-
The 40-251-121 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 925Ω with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
AC and DC Current Sources
-
Programmable AC and DC current sources that provide precise, low noise, stable currents for a number of applications.
-
Product
GPIB-USB-HS+ , USB, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device
783370-01
-
USB, Analyzer Software Included, IEEE 488 GPIB Instrument Control Device - The GPIB‑USB‑HS+ is an IEEE 488 controller and portable analyzer device for computers with USB slots. You can use this device to integrate an instrument into your system using GPIB as well as to troubleshoot and solve GPIB hardware and software problems. The GPIB‑USB‑HS+ achieves maximum IEEE 488.2 performance. With no GPIB cable required for instrument connection, you can use the Hi‑Speed USB port to control up to 14 programmable GPIB instruments. The improved design allows for size compatibility with almost every instrument, adds analyzer functionality, and reduces the overhead to generate faster turnaround times in your application. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-334-HI
-
The 40-230-334-HI (PXI) and 42-230-334-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 102kΩ with 2Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-030
-
The 40-297A-030 (PXI) and the 42-297A-030 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 6.97 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-010
-
The 40-297A-010 (PXI) and the 42-297A-010 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 31 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Digital Signal Processors
-
Powerful Field Programmable Gate Array (FPGA) based Digital Signal Processors (DSP) with large memory, fast PCIe and optical data interfaces (ODI)
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel, 1 Ω to 61 Ω
40-297A-111
-
The 40-297A-111 (PXI) and the 42-297A-111 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 61 Ω, 0.25 Ω Resolution. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Synchro to Digital-Resolver to Digital Converters
HSDC-HRDC
-
Computer Conversions Corporation
HSDC & HRDC Series are Miniature, Tracking Synchro and Resolver to Digital Converters with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command for military and industrial applications.
-
Product
PXI Switch - 24-CH 2-Wire Multiplexer Module
PXI-7921
-
ADLINK PXI-7921 is a relay multiplexer which consists of 24 2-wire relays (DPDT, 2 Form C). As a multiplexer, the PXI-7921 provides 48x1 1-wire, 24x1 2-wire and 12x1 4-wire configurations. Users could choose one of the configurations by software. PXI-7921 typically connects one instrument, such as a DMM, a digitizer or a signal source, with many points which need measurement or excitation. The contact position of the relays can be changed either by direct software commands or by following the instructions previously stored in the on-board scan list. The scan list advances upon the trigger from external measurement devices, such as a DMM. The scan list could also advance when the scan-delay timer expires. In the PXI-7921, PXI trigger functions are supported and software programmable. Multiple modules can therefore be synchronized without additional field wiring.
