Comparators
Contrast similar or divergent values.
-
Product
Flash Vs. Scan
-
A LiDAR system can observe the complete field of view (FOV) at once, called Flash systems. Flash typically works well for short to mid-range (0-100m), and by capturing the complete scene at once also objects with high relative speeds can be detected properly. Another implementation is to focus on a subset of the FOV, consequentially look at the next subsets, until the complete FOV is covered, called Scanning. Scanning can focus the light on the subset instead of the full FOV, and therefore can do object detection at a longer range compared to Flash.
-
Product
Pressure Comparator (System F)
Type T
-
AMETEK Sensors, Test & Calibration
Type T hydraulic comparator (System F) is a self-contained high volume pressure source capable of producing pressure up to 15 000 psi. It is ideal for testing gauges and setting hydraulic relief valves and pressure switches. Multiple models are available for hydraulic oil, water, or both.
-
Product
Biconic Logarithmic Periodic Antennas
Stacked LPDA
-
The stacked Logarithmic Periodic Dipole Antenna consists of two ordinary Log.-Per. structures. The excellent characteristics (flat gain over a large bandwidth, low SWR) of the ordinary Log.-Per. designs could be maintained using the stacked LP design. The stacked design helps to focus the directional pattern of the H-plane somewhat, resulting in a typical gain improvement of ca. 2-3 dB compared to an ordinary LPDA. This is especially important for immunity testing, where a maximum fieldstrength and a good field uniformity is required. The beamwidth in the E-plane and the H-plane are nearly identical, providing an optimised illumination of the EuT with minimised ground reflection influence. Further the STLP 9128 C has an excellent cross-polar rejection.
-
Product
Low pin and internal configurable analog MCU
RL78/G11
-
The RL78/G11 microcontroller line-up concept is based on small packages like 20 to 25pin, in small 16KB flash memory and rich analog peripherals such as A/D converters, D/A converters, comparators and PGA and these are configurable as PGA+ADC+VBGR, PGA+CMP, CMP+DAC/VBGR, or PGA+CMP+DAC/VBGR. Using the smart features like DTC and ELC a lot of peripherals can be connected internally to reduce CPU workload and can save overall power consumption. It also supports very low power operation (100 uA @ 1 MHz ) and a high speed 4µs wake up. Available in small 3x3mm² WFLGA , 4x4mm² HWQFN and standard 20pin LSSOP, this MCU line is suitable for sensor application, Lighting/power sources and many small appliances.
-
Product
Water Quality Analyzer(COD,TN,TP,ammonia,heavy Metals)
SIA-3000
-
The SIA-3000 series is a new generation of miniaturized water quality online analyzers. Compared to the SIA-2000 series, it is easy to operate, highly integrated and produces far more accurate readings. Not only is it a superior appearance, but it also has improved user experience. It is suitable for miniature water quality monitoring stations, monitoring mobile waters and other similar application scenarios.
-
Product
Arbitrary Function Generator PXI Card
GX1200/GX1201
Waveform Generator
The GX1200 and GX1201 are high performance, single-channel PXI arbitrary waveform generators that combine a function generator, arbitrary waveform synthesizer, programmable sequencer, pulse generator, and modulation generator in one instrument. The GX1200 Series delivers all this at a lower cost than comparable benchtop or VXI-based instruments.
-
Product
1000W Ferroresonant Power Supply
Series PRR
-
Kepco's PRR are 1000 Watt rack mounted laboratory systems power supplies that offer the low cost and very high dependability of ferroresonant voltage stabilization.The ferroresonant stabilizing technique provides extraordinary isolation from a wide variety of source noise. It is inherently short-circuit proof and cannot expose delicate loads to overvoltage hazards. Hence no crowbar, fuses, or bounding circuits are needed. Ferroresonant power supplies use no noise-producing switches or oscillators. Voltage setting is independent of delicate control settings or diode references and requires no comparators, references, or limiters. Efficiency is 70-80%.
-
Product
Low Pressure Cylinder Leak Tester
CLT4PB
-
Tests leakage at 35psi compared to 100psi in current leakage tester. Lower pressure prevents smaller bore cylinders from moving as they might under 100psi. Works well on small engines found in recreational, marine and other applications.
-
Product
Thermal Sensitivity Tester
NTE-2A
-
The NTE-2A Thermal Probe is a sophisticated, non-invasive device for the clinical evaluation of neuropathy and the assessment of short fiber neurological function. Individual thresholds are compared to normals to statistical normals. These results provide an accurate means of tracking chronic changes in small fiber nerve function. It can be used for pain studies and in any application were a variable, accurately-controlled temperature stimulus is required. The NTE-2A is often used in conjunction with the Vibratron II to assess peripheral neuropathies.
-
Product
Fanless Embedded System With Intel® Celeron® J1900, HDMI, VGA, 2 GbE LAN, 4 USB, 3 COM And 10 To 34 VDC
eBOX626-842-FL
-
The eBOX626-842-FL is the energy-efficient fanless embedded box PC suited for rugged and extreme applications with its extended temperature and wide range voltage capability. The extreme compact box PC utilizes an onboard Intel® Celeron® quad core processor J1900 2.0GHz (codename: Bay Trail-D) to boast both excellent performance and ultra-low power consumption. The ultra-slim fanless embedded computer supports system memory up to 8 GB with one DDR3L-1066/1333 SO-DIMM socket and offers HDMI and VGA display outputs, offering not only high computing capability but also excellent graphics performance. Integrated single-chip design, the brand new ruggedized embedded system is lighter and thinner compared to previous eBOX620 series. Supporting wide operating temperature between -20°C to +55°C and 10 to 34VDC wide DC input voltage, the fanless embedded PC is excellence for wide range of industrial applications. Its passive cooling design also offers quiet, fanless operation with low power consumption, and all at an attractive price point. With full-featured of I/O interfaces, the Intel® Celeron®-based eBOX626-842-FL supports two RS-232/422/485 ports, one RS-232 port, VGA, HDMI, audio, dual Gigabit Ethernet LAN ports, four high-speed USB 2.0, three SMA type connector openings for antenna, 10-34VDC power input connector, and one ATX power switch. One 2.5" SATA HDD drive bay and mSATA are also embedded in the embedded computer to possess sufficient storage.
-
Product
RF Electronic Calibration Module (ECal), DC/300 KHz To 9 GHz, 3.5 Mm, 2 Port
85093D
-
The Keysight 85093D RF electronic calibration (ECal) module makes the calibration of vector network analyzers fast, easy, and accurate. ECal is a precision, single-connection calibration technique for your vector network analyzer. Performing a full two-port calibration takes less than half the time and a number of connections using ECal versus mechanical calibration kits. Furthermore, the accuracy of the calibration is comparable between electronic and mechanical methods. Traditional mechanical calibrations require intensive operator interaction, which is prone to errors. With ECal, the operator simply connects the ECal module to the network analyzer and the software controls the rest.
-
Product
Calibration Measurement
-
The process of comparing a measuring instrument's readings to a known, more accurate standard to detect and correct errors.
-
Product
Programmable LCRZ Meter
DU-6212/6215/6216
-
Delta United Instrument Co., Ltd.
Wide Measuring Range & High accuracy 0.1%Zeroing Offset FunctionProvided HI/LOW limit and BIN Sorting comparator function, to meet your needed.100 sets of memory, can be saved test parameter and comparator setting, easy to use.Cover up free, system firmware upgrade can be update via RS-232, easy to maintenanceEasy Test Condition Setting with Auto Parameter Selection & Auto Ranging Function High speed FADC, max. test speed up to 55 meas./sec, faster your automation equipment240*64 Graphic LCD display, can be read the reading clearly and easier.User friendly programmable interface, easy to useProvided RS-232C and Handler combinatorial interface option, to meet your needed
-
Product
Binary to BCD Converter
BAC300
-
Computer Conversions Corporation
The BAC series of Binary to BCD converters will convert binary angle data to 5 digit BCD data scaled in degrees and decimal fractions of degrees. Units with display and/or data outputs are available. Custom scaling of the output to represent actual physical units of measure can be provided easily (i.e.: feet, lbs., meters, mills, etc.) They will also accept encoder outputs and display them at extremely low cost when compared to previous solutions.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 80 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5942-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Desktop Type AE Systems
-
Compared to the online remote AE systems, desktop type AE systems are connected to and accessible within the local network, either directly by wires or via wireless local networks. Such desktop type AE detection system is normally use with a computer or laptop on a desk or table on site or near the facility. It is usually conducted and real-time controlled by professionals to accurately locate the AE ‘Hits’ sources and analyse the AE data in full aspects. There are two types of AE systems that can be used as desktop type systems, the SAEU3H multi-channel AE system and the RAEM systems respectively.
-
Product
Test Systems
-
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
Product
Phase Noise Analyzer
DCNTS
-
Noise eXtended Technologies S.A.S.
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 20 MS/s on 4 Channels (Single Ended) or 4 Channels (Differential)
M2P.5926-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Modulator
SFT2406G
-
Hangzhou Softel Optic Co., Ltd.
SFT2406G DVB-T/T2 modulator is our new product developed complying with the DVB-T/T2 standard. With its advanced modulating technology, this modulator can effectively make use of the ground spectrum resources and make it possible to provide reliable signals for fixed, mobile and portable devices. Compared with DVB-T, the channel capacity is increased by 30% under the similar carrier to noise ratio (CNR) threshold. Moreover, this device can be upgraded and controlled through network system, which allows it to be widely used in setting up digital broadcasting network and provide good signals for scientific laboratory and DVB-T/T2 STB.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5912-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Frequency Generation & Monitoring
-
Timetech reference generators, phase comparators, and synchronized oscillators.
-
Product
Advanced 4-Axis Servo & Stepper Motion Controller with High-Speed Triggering
PCI-8164
Motion Controller
ADLINK PCI-8164/PXI-8164 is an advanced 4-axis motion controller. Compared with the PCI-8132/34 series, PCI-8164/PXI-8164 offers better linear and circular interpolated move and continuous contouring performance-ideal for advanced pulse train motion control solutions and complicated motion and pick-and-place applications.
-
Product
Distributed Test Manager
DTM
-
The Distributed Test Manager (DTM) is a Windows™ application which enables many different types of system level testing by simulating multiple devices in a system. DTM is a system level simulator that is unique compared to other Triangle MicroWorks tools which test the communications of a single device. DTM is a highly extensible tool with multiple options for configuring devices, creating test cases, and simulating data in the system.
-
Product
40Gb/s DQPSK Receiver
-
The integrated DQPSK receiver incorporates an optical phase demodulator (delay-line interferometer or DLI) with 2 pairs of balanced photo-diodes and 2 linear TIAs into a single butterfly package. Compared with the currently available discrete solution in which a separate DLI and a separate receiver are used, the integrated DQPSK receiver eliminates labor intensive fiber routing and coupling (between the DLI and the balanced receiver) as well as the skew control. Moreover, the integrated DQPSK receiver offers a smaller footprint suitable for today’s demanding high speed transponder applications.
-
Product
OnyxFX FlexorSet 4-Ch. 250 MHz A/D, 2-Ch. 800 MHz D/A - 3U VPX
Model 5973-312
-
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 250 MHz 16-bit A/Ds- One digital upconverter- Two 800 MHz 16-bit D/As- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical Interface for backplane gigabit serial interboard communication- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Also available as Model 7070-312- See comparable JadeFX Xilinx Kintex UltraScale FPGA Family:Model 5983 JadeFX Kintex UltraScale Processor and FMC Carrier - 3U VPX
-
Product
Solar Array Simulator
Simulator
Among other things, solar array simulators are required for testing satellite power supplies. An SAS (Solar Array Simulator), consisting of an interconnection of several Solar Array Simulator modules, maps the solar panels and displays the individual strings connected in parallel. Optionally, the individual SAS modules are monitored by a Second Level Protection, so that the test object is not damaged in case of errors with the voltage sources. Additional circuitry is implemented via project-specific test modules. The signal path to the DUT can be separated, e.g. for dynamic current measurements.The Keysight Solar Array Simulators used were specially developed for satellite applications and cover the significantly higher requirements regarding the control speed of MPP tracking compared to terrestrial applications.
-
Product
Integrated Leeb Hardness Tester
TIME®510D
-
Beijing TIME High Technology Ltd.
TIME®510D is an updated version of TIME5120 Leeb Hardness Tester, the cheapest and most popular leeb hardness tester manufacturer by TIME. It is portable and integrated with universal impact device D. Compared to TIME5120, the new product offers significant improvements in both outlook and performance.
-
Product
Palmtop Raman Spectrometer
PR-1w
-
The PR-1w Palmtop Raman spectrometer is a compact unit that contains a powerful 50 mW 785 nm laser, coupled to a high resolution spectrograph with CMOS detector. Compared to many of the commercially available Raman instruments, the PR-1w is a user-friendly Raman spectrometer that can be used by virtually anyone with minimal training. It can be used in many different environments, and variety of measurement concepts, such as in-line and in-situ measurements. With a comprehensive range of optional accessories, the PR-1w can be optimized for specific applications.
-
Product
Spectrum Analyzer
BB60C
-
The BB60C streams 140 MB/sec of digitized RF to your PC utilizing USB 3.0, providing an instantaneous bandwidth of 27 MHz, and sweep speeds of 24 GHz/sec. The BB60C has significantly improved performance compared to the BB60A. The BB60C has improved spurious-free dynamic range (SFDR) by 20 dB, flattened the noise floor and band transitions by more than 8 dB, and extended operating temperatures from -40ºC to +65ºC (Option 1). The BB60C also adds new functionality in the form of configurable I/Q streaming bandwidths which will be retroactively available on the BB60A.
