PMC Modules
-
Product
PXIe-5652, 6.6 GHz RF Analog Signal Generator
781217-01
Signal Module
PXIe, 6.6 GHz, PXI RF Analog Signal Generator—The PXIe‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 2-Bank 6GHz SMA
60-802-002
Multiplexer Module
The 60-802-002 is a 4-channel, 2-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers.
-
Product
PXI 4 Slot BRIC Module, 1 Resource Distributor, 1 Bus Matrix Inputs
40-569B-011
Matrix Switch Module
The 40-569B is a range of high-density BRIC matrices capable of switching up to 2A and up to 200VDC/180VAC. These large PXI matrix modules are available with multiple configurations in 4 or 8 slot sizes and are constructed using high-quality electromechanical relays. The 40-569-011 is a 4 slot module fitted with 1 Bus Matrix Inputs card and 1 Resource Distributor card.
-
Product
NI-9226, 8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module
783864-02
Temperature Input Module
8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module - The NI‑9226 is a resistance temperature detector (RTD) input module. You can configure the NI‑9226 for two sample rate modes: high sample rate or high resolution. The NI‑9226 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3‑ or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per-channel current excitation. The NI‑9226 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm
50-294-023
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
SMARC Short Size Module with NXP i.MX 8M Mini SoC
LEC-IMX8MM
Computer on Module
ADLINK LEC-IMX8MM, the first SMARC revision 2.1 compliant module offering superior power efficiency, is based on the low-power NXP i.MX 8M Mini processor (dual or quad core Arm Cortex-A53) with integrated Vivante GC NanoUltra graphics for improved processing capabilities. The LEC-IMX8MM is your ideal, cost-effective solution for various general-purpose edge and IoT applications.
-
Product
LXI 64x4, 10A, 1-pole Matrix
60-600-003
Matrix Switch Module
A high power single pole matrix module capable of switching up to 400VDC/250VAC, 10A (300W/2500VA max power)
-
Product
PXI Digital I/O And Prototyping Modules
Prototyping Module
Programmable Input Threshold and High-Side or Low-Side Drive Capability Available on Some ModulesOptically Isolated Input/Output for Interfacing to Electrically Noisy Environments Available on Some ModulesTTL Inputs and Outputs Suitable for Interfacing to External LogicOpen Collector/Drain Transistor Output Versions Suitable for Driving Internal or External Relay Coils
-
Product
PXI 8 Slot BRIC 88x4 2-pole (2 sub-cards)
40-562A-122-88X4
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 3A Power MUX BRIC, 12-Channel, 24-Pole
40-571-106
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI Very High Density Multiplexer, 24-Channel, 8-Pole
40-675A-002-24/8
Multiplexer Module
The 40-675A-002-24/8 is a 24-channel, 8-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1Ω to 31.5Ω
40-251-110
Programmable Resistor Module
The 40-251-110 is a programmable resistor module with 4 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 1.5Ω to 1.81kΩ
40-253-022
Programmable Resistor Module
The 40-253-022 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Mini Coax, Module, Receiver, 90 Series, 37 Position
510104301
Receiver Module
Primary mating module 510108276.*Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
Product
Dsub25 To 5 SMB Adapter
PX0106A
Adapter Module
Keysight's PX0106A Adapter converts Dsub25 outputs to five SMB outputs with path through connection. It supports the Keysight M9614/15A.
-
Product
PXI MUX 1 Bank, 64 Channel Screened 1 Pole
40-610-021-S-1/64/1
Multiplexer Module
This series of high density multiplexer modules feature a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 200-pin connector. Inter-bank linking relays allow multiplexer size to be increased in multiples of in multiples of three by joining the common terminals of adjacent banks. Closing one linking switch produces a 6-channel multiplexer, closing all linking switches produces an 54-channel multiplexer
-
Product
PXI 8 Slot BRIC 88x8 1-Pole (4 sub-cards)
40-562A-121-88X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
LXI Microwave Matrix, 10GHz, Single 4x4, Terminated
60-750-144-B
Matrix Switch Module
The 60-750-144-B is a single 4x4 10GHz microwave matrix with internal termination. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection.
-
Product
PXI 8 Slot BRIC 150x16 1-Pole (10 sub-cards)
40-561A-121-150X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
LXI High Density 384x4 2-Pole 2A Matrix With BIRST
60-556-026
Matrix Switch Module
High density double pole matrix capable of switching up to 300VDC/250VAC, or 2A (60W max). The use of high quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
Product
PXI/PXIe RF Matrix, 16x4, 150 MHz, 50 Ω, SMB, With Y Loop-thru
40-724-012-L
Matrix Switch Module
The 40-724-012-L (PXI) and 42-724-012-L (PXIe) are 16x4 RF matrix modules with y-axis loop-thru and are suitable for switching frequencies up to 150 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 16-Channel, 2-Pole
42-739-002
Multiplexer Module
The 40-739-002 (PXI) and 42-739-002 (PXIe) are dual 16-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
PXI 3A Power MUX BRIC, 12-Channel, 16-Pole
40-571-204
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
Coax, Module, Receiver, 20/26 GHz, 90 Series, 17 position, incl. strain relief plate
510104287
Receiver Module
Coax, Module, Receiver, 20/26 GHz/75 Ohm HD, 90 Series, 17 position, incl. strain relief plate(For use w/ 20/26 GHz contacts & SMA adapter. Includes strain relief plate) Primary mating module 510108240.*Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
Product
PXI 12-Slot BRIC Matrix, 484x4 2-Pole (11 sub-cards)
40-562B-322-484X4
Matrix Switch Module
The 40-562B-322-484X4 is a high density BRIC12 matrix module with a size of 484x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI High Density Precision Resistor Module, 6-Channel, 4Ω to 1.51MΩ
40-298-050
Programmable Resistor Module
The 40-298-150 is a high density programmable resistor module with 3 channels which can be set between 4Ω and 1.51MΩ with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP8T, 18 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
40-788-022-TE
Multiplexer Module
The 40-788-022-TE (PXI) and 42-788-022-TE (PXIe) are dual failsafe SP8T 18 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
PXI High Density Precision Resistor Module, 6-Channel, 3.5Ω to 773kΩ
40-298-043
Programmable Resistor Module
The 40-298-043 is a high density programmable resistor module with 6 channels which can be set between 3.5Ω and 773kΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-133
Precision Resistor Module
The 40-297A-133 (PXI) and the 42-297A-133 (PXIe) are 4-channel programmable resistors with a range of 2 Ω to 52.4 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
EtherCAT IO Slave For M-Type Modules
ECAT-IO M Series
M-Type Modules
The ADLINK complete EtherCAT solution, from hardware to middleware to software, with every element tailored for dedicated EtherCAT functionality, includes PCIe-833x and SuperCAT master controllers, ECAT & EU slave systems, and remote monitoring and control providers. As well, ADLINK’s Softmotion one-stop control kernel delivers flexible and easy-to-use intelligent platforms for driving next-generation modern Smart Factories. ADLINK’s ECAT IO system features a modular design for flexible high channel density, rugged construction, easy maintenance, and compatibility with third-party EtherCAT master products. Precise time-deterministic control enables I/O synchronization for critical applications, while the flexible terminal block design supports multiple wiring methods. The ECAT’s unique structural and electronic design supports hot swapping of modules, reducing repair time, and offers full operability from 0°C to 60°C. The ECAT slave system is also fully compliant with the EN 61131-2 standard for shock and vibration and EN 61000-6 for heavy industrial EMC protection, as well as receiving an emission certificate.
