Multifunction I/O
See Also: Mass Interconnect
-
Product
32-CH DI & 32-CH DO 12 MB/s High-Speed Card
PCIe-7200
Digital I/O Module
- x1 lane PCI Express interface- 32-CH TTL digital inputs and 32-CH TTL digital outputs- Up to 12 MB/s transfer rate- Onboard programmable timer pacer clock- Support handshaking digital I/O transfer mode- Bus-mastering DMA for both digital inputs and outputs- 5 V power available on connectors- Compact, half-size PCB
-
Product
PCI-6515, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Sink Output, Bank-Isolated Digital I/O Device
778835-01
Digital I/O Module
The PCI-6515 is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6515 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
96-Channel Digital I/O Plug-In
1260-114
Digital I/O Board
The high channel count of the digital I/O plug-ins allows a significant portion of digital I/O to be realized in a single slot of the Adapt-a-Switch™ carrier, saving valuable VXIbus chassis space. The 1260- 114 provides 96 digital I/O channels in twelve groups of eight bits each.
-
Product
32 Input, 32 Output USB Modular Digital I/O
U2651A
Digital I/O Module
The Keysight U2651A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
Product
2.4/5GHz Wi-Fi I/O Module With 4AI/4DI
WISE-4250-S214
Wireless I/O Module
Integrates 4 analog inputs (AI) and 4 digital inputs (DI) in a compact designAnalog Inputs support Burn-out Detection (4~20mA only) to prevent system failures and unplanned downtimeDigital inputs support High/Low value alarms, Latch, and Momentary Alarm modes for flexible event monitoringSupports 3kHz high-speed counter input (32-bit with 1-bit overflow) on digital input channelsComplies with IEEE 802.11ac (2.4GHz/5GHz) dual-band Wi-Fi for stable and high-speed wireless communicationEnsures secure data communication with WPA3/TLS 1.3 encryption and X.509 certificate authenticationEnables seamless cloud integration via MQTT and RESTful APIs, supporting direct data uploads to AWS, Azure, SCADA, and WebAccess platforms
-
Product
Industry Pack Carriers and Digital I/O
CPCI-4SIP-6U
Digital I/O Module
The CPCI-4SIP-6U module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-4SIP-6U is the perfect solution. There are four (4) Industry Pack sites providing up to 200 I/O pins accessible from either the front panel or the rear back plane.
-
Product
Bi-Directional Differential-TTL I/O PXI Card
GX5641 Series
Digital I/O Module
The GX5641 is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), functional test, and factory automation applications. The GX5641 consists of 64 bi-directional TTL-differential I/O channels. Each channel has two ports (TTL and differential) which can be individually set to operate in either conversion or static I/O modes.
-
Product
8-Ch Digital Input (2-Ch Timestamp & 6-Ch Without Timestamp) EtherCAT Slice IO Module
AMAX-5051T
EtherCAT Slice IO Module
Precise and Deterministic Digital Input2-ch Timestamp Digital Input6-ch Regular Digital InputTimestamp resolution: 1nsRising Edge & Falling Edge DI Latch
-
Product
PXI Semi-Dynamic Digital I/O Module, 48-Channel
40-419-002
Digital I/O Module
The 40-419-002 is a 48-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
64 Input USB Modular Digital I/O
U2652A
Digital I/O Module
The Keysight U2652A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
Product
PXIe-6569, PXI FlexRIO Digital I/O Module (64-out LVDS, 8 SE, KU060)
787281-01
Digital I/O Module
1.25 Gbit/s, Kintex Ultrascale FPGA, 64 LVDS Channel FlexRIO Digital I/O Module - The PXIe-6569 provides a digital I/O interface along with a user-programmable FPGA for flexibility to fit a variety of interfacing and application needs. This module can interface with up to 64 … single-direction low-voltage differential signal (LVDS) channels and eight bidirectional single-ended channels. You can use the PXIe-6569 for real-time interfacing of standard protocols or implementing customized protocols.
-
Product
PC/104-based Analog Input, Analog Output, and Digital I/O Board
PCM-MIO-A-1
Digital I/O Board
The PCM-MIO-A-1 is a versatile, PC/104-based analog input, analog output, and digital I/O board designed for high-accuracy and high-channel-count analog and digital I/O. The board is based upon Linear Technology’s precision converters and voltage references which require no external calibration. The digital I/O utilizes WINSYSTEMS’ versatile WS16C48 Universal I/O controller functionality, also available on many of our SBCs and other I/O products.
-
Product
PCIe-7820, Kintex 7 160T FPGA Digital Reconfigurable I/O Device
785361-01
Digital I/O Module
The PCIe‑7820 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PCIe‑7820 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in-the-loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
Product
DB15F-DB15M, 15-Pin Female to Male DSUB I/O Cable, 1M
141856-01
Multifunction Cable
The DB15F-DB15M connects compatible NI devices to accessories or cables with D-SUB connectors.
-
Product
Digital and Serial I/O
Digital I/O Module
At Abaco, we're committed to the future of your VME systems, and we provide you with the flexibility and functional density you need.
-
Product
3-meter Laser Head Cable
10882A
Multifunction Cable
The 10882A 3-meter Laser Head Cable is used to connect the 5519A/B Laser Head to the E1735A USB Axis Module for the 5530Laser CalibrationSystem.
-
Product
6U PXI Multi-Channel Analog I/O PXI Card
GX3348 Series
Digital I/O Module
The GX3348 is a multi-channel analog I/O 6U PXI card which provides (3) programmable sources, a ground source connection, a pulse / square wave generator (A version only) and a 4 x 48 or 4 x 64 matrix - allowing the user to route the 3 sources, or ground to any of the 48 or 64 I/O channels. In addition, each I/O channel can be connected to a 16-bit A to D converter, providing DC voltage measurement capability for each channel. The module also offers (8) static digital I/O for controlling / monitoring a UUT's digital signals.
-
Product
FPGA PXI Digital I/O Card
GX3500
Digital I/O Module
The GX3500 is a user configurable 3U FPGA PXI card which offers 160 digital I/O signals for specific application needs, as well as providing pin for pin compatibility with NI PXI 7811R and 7813R FPGA cards. The card employs the Altera Cyclone III FPGA which can support clock rates up to 150 MHz and features over 55,000 logic elements and 2.34 Mb of memory.
-
Product
Keysight 64-bit Digital I/O with Memory and Counter for 34980A
34950A
Digital I/O Module
The Keysight 34950A module for the 34980A Multifunction Switch/Measure Unit has 64 bi-directional lines configured as eight 8-bit channels. Each 8-bit channel has programmable polarity and thresholds up to 5V. The memory is useful for simulating and capturing digital patterns up to 10 MHz. It provides configurable handshaking protocols for a wide variety of applications.
-
Product
PCI-6518, 32-Channel, ±30 V, 16 Sink/Source Inputs, 16 Source Outputs, Bank-Isolated Digital I/O Device
779084-01
Digital I/O Module
The PCI-6518 is an industrial digital I/O interface, with two banks optically isolated channels. The device is ideal for industrial control and manufacturing test applications. The PCI-6518 module is an industrial digital I/O interface, with eight banks of isolated channels. You can wire each input bank in a source or sink configuration. With programmable power-up states, you can configure the initial output states in software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6518 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions.
-
Product
PCI-7813, 3M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779370-01
Digital I/O Module
The PCI‑7813 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7813 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware-in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
Product
32-Ch Isolated Digital I/O USB Module
USB-4750
Isolated Digital I/O Module
Compatible with USB 1.1/2.0Bus-powered16 isolated DI and 16 isolated DO channelsHigh voltage isolation on all channels (2500 VDC)High sink current on isolated output channels (200 mA/Channels)Supports 5 ~ 60 VDC isolated input channelsInterrupt handling capabilityTimer/Counter capabilitySuitable for DIN-rail mountingOne lockable USB cable for secure connection included
-
Product
4-Ch Analog Output EtherCAT Slice IO Module
AMAX-5024
EtherCAT Slice IO Module
Channels: 4Output Type: V, mV, mAOutput Range: 0~5V, 0~10V, ±5V, ±10V, 4~20mA, 0~20mAResolution: 16-bit with accuracy, 0.01% FSR@25°CSlew Rate: ConfigurableDrift: ± 50 ppm/°CCurrent Load Resistor: Max. 500 ΩVoltage Load Resistor: Min. 1KΩ
-
Product
PXI-6529, 48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module
779949-01
Digital I/O Module
48-Channel, Sink/Source Inputs, Channel-Channel Isolated PXI Digital I/O Module—The PXI‑6529 is an industrial, parallel digital input interface. PXI‑6529 devices are ideal for a variety of applications from automotive design, industrial factory automation, and machine control to aerospace, laboratory research, and biomedical applications. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6529 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PXI 32 Channel I/O, High Side Driver
40-413-001
Digital I/O Module
A 32 channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only (shown here), alow side only and a combined high and low side each capable of driving 2A loads. Eachoutput is fully protected against over-voltage, over-current and thermal overload,ensuring robust and reliable operation in the toughest test environments. For highside voltage driving the high side voltage source is supplied from an external voltagesource, permitting the module to drive high capacity loads without impacting thePXI chassis power supply.
-
Product
Digital Channel, 10 MΩ Input, ±25 V, 8 Channel
CX1152A
Digital I/O Adapter
The CX1152A Digital Channel provides 8-channel digital trigger for the CX3300 Device Current Analyzer series, which is useful when a low power device with digital I/Os is evaluated. Only the CX3324A mainframe has the interface of this product. The input impedance of each channel is 10 MΩ in order to minimize the load current from the digital channel.
-
Product
SH25F-25M-2 25-Pin Female to Male Shielded I/O Cable, 2 m
192568-02
Multifunction Cable
SH25F-25M-2 25-Pin Female to Male Shielded I/O Cable, 2 m
-
Product
NI-6584, 16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
781290-01
Digital I/O Adapter
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter
-
Product
PXI-6281, 16 AI (18-Bit, 625 kS/s), 2 AO, 24 DIO, PXI Hybrid, Multifunction I/O Module
779121-01
Multifunction I/O
16 AI (18-Bit, 625 kS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXI‑6281 offers analog input, correlated digital I/O, two 32‑bit counter/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXIe-6535, 32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module
780695-01
Digital I/O Module
32-Channel, 10 MHz, 40 MB/s PXI Digital I/O Module—The PXIe‑6535 can continuously stream data over the PXI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
