Frequency to Voltage Converters
A device which cleans AC Sinewave signals from an AC source.
-
Product
LXI High Frequency Matrices
-
Pickering's LXI high frequency (HF) matrix modules are suitable for switching frequencies up to 50MHz. They have an impedance of 50 and uses SMB signal connectors or with a larger case size is uses BNC connectors. This HF matrix is designed to provide a simple and scalable bidirectional matrix for radio frequencies and is intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
NI-9269, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781098-02
Voltage Output Module
100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The NI‑9269 is a channel‑to‑channel isolated analog output module. The NI‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes.
-
Product
Frequency Multiplier
SMZ
-
R&S®SMZ frequency multipliers combine easy handling and precise output levels in the frequency range from 50 GHz to 170 GHz. They can be used in diverse applications, e.g. in the automotive sector with distance radars, in astronomy with sophisticated telescopes and in radar interferometry for analyzing the earth’s surface.The frequency multipliers are available in the R&S®SMZ75 (from 50 GHz to 75 GHz), R&S®SMZ90 (from 60 GHz to 90 GHz), R&S®SMZ110 (from 75 GHz to 110 GHz) and R&S®SMZ170 (from 110 GHz to 170 GHz) models. An optional attenuator (available for R&S®SMZ75, R&S®SMZ90 and R&S®SMZ110) can be integrated in the same housing as the frequency multiplier, simplifying handling. The R&S®SMZ can be controlled via USB.
-
Product
Frequency Discriminators & IFM
-
PMI offers a full line of RF and Microwave frequency discriminator products that range from a few MHz up to 18.0 GHz. Many options are available. If you do not see exactly what you need, please e-mail your requirement to sales@pmi-rf.com so we can propose an instant solution.
-
Product
High Voltage Differential Probes
-
High voltage differential probes provide high CMRR over a broad frequency range (up to 400 MHz) to simplify the measurement challenges found in noisy, high common-mode power electronics environments. The probe’s design is easy-to-use and enables safe, precise high voltage floating measurements.
-
Product
High Frequency RF and Microwave USB Programmable Signal Generators
LMS Series
-
The Lab Brick LMS series of high frequency RF and microwave USB-compatible, synthesized signal generators cover a frequency range from 0.5 MHz - 20 GHz with low noise, fast 100-microsecond switching time, and fine 100 Hz frequency resolution. They require no additional DC supply voltage and offer advanced features such as phase-continuous linear-frequency sweeping, internal/external 10 MHz reference, and optional pulse modulation. GUI software can track and control several connected signal generators, simplifying multiple-signal test setups. Each device stores settings in internal memory, allowing it to power up in a specific instrument state.
-
Product
Digital Three-Phase Uni & Directional Converters
-
Start Power equipments series SCxQML230 are totally controlled three-phase digital converters operating up to 500 Vac voltage, 360A current, frequency between 45 and 62Hz; they are suitable for speed and motor torque regulation. Sizes with current up to 9000 A are available in different mechanical dimensions.
-
Product
High Frequency Digital Surge Tester & DC Hi-Pot Tester
SPM
-
High Frequency Digital Surge Tester and DC Hi-Pot Tester (similar to the "SP" Model) together in a compact cabinet. Take this portable tester to your test site and accurately perform Surge, Hi-Pot, PI and Resistance Tests.
-
Product
Power Frequency Magnetic Field Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Power frequency magnetic field simulator is a special designed instrument with high reliability according to the features of the power frequency magnetic field immunity test for electrical and electronic products.
-
Product
Isolated A/D Converters
-
As the world’s leading supplier of data converters, Analog Devices is constantly introducing new A/D converters (ADCs) that drive system architectures. In the motor control arena, ADI’s converters solve the challenges associated with current and voltage monitoring, optical encoder feedback, and resolver-to-digital conversion. The introduction of the isolated ADC with its 3.75 kV standoff voltage is one example of ADI’s breakthroughs in performance and integration to ease the burden of design.
-
Product
High Voltage Divider
-
High voltage measuring divider in capacitive or resistive construction.
-
Product
Low Voltage Detectors
LVD-17
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled smart voltage detector.● Bright LED and audible alarm sound when voltage is present.● Designed for non-contact voltage detection.● Sensitivity adjustable with thumbwheel.● Adjustable for use on power wiring plus lighting, thermostats and other low voltage circuits.● LED indication for battery condition.● Identify Hot and Neutral.
-
Product
Induced Over Voltage Test Set
-
We are highly experienced in manufacturing and exporting Induced Over Voltage/DFDV Test Set. It is widely used in electrical and power sector to test different types of transformers. Our range includes different models of testing set to meet clients' diverse requirements. Manufactured in accordance with industry standards, this Induced Over Voltage/DFDV Test Set is offered to clients at competitive price.
-
Product
AC Voltage and Frequency Transducers
NMTU/F
-
The NMTU/F device is an AC voltage and frequency transducer with two independent analogous outputs. The A output measures AC voltage, the B output measures the frequency of input voltage. That´s why one single NMTU/F transducer is able to replace two customary transducers, thus making it possible to achieve significant savings in installation space.
-
Product
50-Watt DC/DC Converter; Dual Output
55JD1
DC Converter
NAI’s 55JD1 is a 50-Watt DC/DC Converter that accepts a +28 VDC input. This COTS unit provides full-power output, dual at a baseplate temperature of +100° C.
-
Product
PoE Voltage Monitor Detect & Verify
PE-400
-
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
Product
Frequency Extenders
-
A frequency extender is an electronic device that allows high-fidelity analog audio to be sent over regular POTS telephone lines, without the loss of higher audio frequencies. It is an extended concept of a telephone hybrid.
-
Product
High Voltage Power Capacitors
-
Lifasa - International Capacitors, SA
Capacitors of correction power of cos φ and filtering of harmonics for AT of Lifasa, are manufactured under the base of the container / stainless steel box and porcelain terminals. There are two types, depending on the connection mode that we are going to use:*Single-phase (1 or 2 terminals) with internal fuses, for connection to the network through a double star. Recommended for networks of tension superior to 11 Kv or need of equipment of high power.*Three-phase (3 terminals) with internal fuses, for direct connection to three-phase network. Recommended for voltage networks lower than 11 Kv.
-
Product
Frequency Converters & Transceivers
-
Mercury Systems’ converter and transceiver products are at the forefront of SWaP-optimized RF integrated products. Through substantial R&D investment and a library of building blocks, Mercury Systems has the capability to rapidly execute on the most complicated of custom transceiver designs. As the OpenVPX industry leader, Mercury Systems knows how to make integration into your system a breeze.
-
Product
Personal Safety Voltage Detector
287 SVD
-
Standard Electric Works Co., Ltd
● Compact, easy to wear and convenient in use.● Usable both indoor and outdoor.● Voltage detection distance: 6.6kV(3.8kV phase to ground) : 40cm ± 20% 11.4kV(6.6kV phase to ground) : 55cm ± 20% 19.7kV(11.4kV phase to ground) : 80cm ± 20% 22.8kV(13.2kV phase to ground) : 85cm ± 20%● Water-proof design. (IP65)● Equipped with self-testing functions.● Able to sense all kinds of AC High Voltage System.● Low power consumption.● CE Certified.
-
Product
Frequency Conversion Rotating Magnetic Fla
MT-2XCF
-
MITECH MT-2XCF rechargeable frequency conversion rotating magnetic flaw detector is based on principle that the leakage magnetic field can absorb the magnetic powder. Make use of magnetic yoke magnetized the workpiece of ferromagnetic material. If there has defects it will produce leakage magnetic field that will adsorb magnetic powder. We could detect the flaw by observing the density of adsorption magnetic powder. It adopts large capacity lithium battery. By the inverter and the phase shifted signal processor to provide power for the detector, it solves the shortcomings of traditional magnetic particle detector relying on the 220V power supply. It has low power consumption and can continuous work for more than 6 hours. And the battery can be charged when the detector is on and off. Especially suitable for the field testing. It can choose the current frequency according to the flaw depth with unique frequency conversion communication design, that improve the detection sensitivity. It’s widely used in aircraft manufacturing, boiler and pressure vessels and other fields. It is a necessary professional precision instrument of quality control, in-service safety monitoring and life assessment.
-
Product
Catalytic Converter Measurement
OMCAT
-
OMCAT catalytic converter measuring systems provide a fast and efficient means of carrying out complex geometrical measurements on exhaust catalytic converters and of determining the gap bulk density (GBD). OMCAT measuring systems feature innovative measurement functions combined with reliable technology. High measurement speed and accuracy and high availability due to their rugged construction are the major strengths of these systems which come to the fore in the harsh conditions which prevail in production environments.
-
Product
Redundant Reference Frequency Shaper
CH7-317
-
Redundant reference frequency shaper Ch7-317 is designed to generate and reproduce frequency and time signals protected from frequency and phase failures based on the results of signal processing from a group of frequency and time keepers.
-
Product
4-20mA Converters
4026
-
SPECTEC Innovative Sensor Solutions
Model 4026 Freq to Voltage or Freq to Current Converter accepts frequency input from any magnetic speed sensor, digital magnetic pickup or Hall effect zero speed sensors. Input and output configurations are field selectable. Input range is adjustable between 1100 Hz - 10 kHz or 75Hz to 1100 Hz. Output selection can be configured as 4-20mA converter, 10-50mA converter, 0-5 V FTV converter or 0-10 V FTV converter. ZERO and SPAN adjustments easily calibrate to almost any measurement range, with little interaction between the adjustments.
-
Product
K-type Thermocouple to Digital Converter
THERMO K click
-
THERMO K click carries the MCP9600 IC from Microchip. Depending on the type of probe it uses the click can measure temperatures from −200 °C to +1372 °C.
-
Product
Frequency Extension Heads for Vector Network Analyzers
FEV
-
These frequency extension modules connect to your existing test ports and leverage the inherent microwave network analyzer’s performance and features to display full port S-parameters: Two measurement architecture available: 1-path/2-port and fully reversing 2 port. Waveguide calibration kits are available as separate accessories.
-
Product
Programmable High Voltage Tester
-
The high Voltage also known as di-electric withstand tester comes with customized facilities like voltage rampup rate zero interlock, Plus the user may specify the voltage level and leakage milliampere level so as to suit its testing needs.
-
Product
JFET Voltage Preamplifier
SIM910
-
Stanford Research Systems, Inc.
The SIM910 and SIM911 are low-noise, programmable preamplifiers which are ideal for a wide range of small signal applications. The primary differences between the two models are their input impedance and input noise.
-
Product
High Voltage Test Sets
-
Nmc's high voltage test sets are manufactured as per the customers requirement ranging from 5kv-100kv ac or dc.
-
Product
Voltage Dip & Swell Simulators
VDS Series
-
A simulator to reproduce voltage variation phenomena in commercial power supplies (AC100V/200V).This type of immunity test against voltage variation phenomena is defined in IEC 61000-4-11 and is widely used in many industries.
