D-Sub
D-Subminature Connector Also known as: DSub
-
Product
IBM PC-XT, Vectorbord Plugbord
4613
-
VECTOR Electronics and Technology, Inc.
62 contacts (31 each side) on 0.100" centers. 3-Hole Solder Pads for interconnecting multiple component leads.I/O mounting area for 37-pin D-sub and ribbon cable connectors. Mounting bracket and hardware kit included (P/N HD36B).
-
Product
50-Pin D-Type Male Solder without Backshell
92-960-050-M
D-Sub Male Connector
This connector is designed to allow users to directly terminate cables with soldered connections. 50-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module.
-
Product
IBM AT/ISA, Vectorbord Plugbord
4617-4
-
VECTOR Electronics and Technology, Inc.
98 contacts (49 each side) on 0.100" centers.Voltage/Ground Plane. Plane surfaces solder-coated for user convenience.To simulate plated-thru holes committed to voltage or groundplanes use Vector T123 eyelets. Vector T123 eyelets available separately (for use without pins). I/O mounting area for up to 70-pin D-sub and ribboncable connectors. Mounting bracket and hardware kit included (P/N HD36B).
-
Product
PXI Programmable Resistor Module
Module
PXI Programmable Resistor Modules are wellsuited for simulating environmental conditions in hardwareintheloop(HIL) validation. The software included provides a simple user interface that accepts inputs in units of temperature or resistance, and configures the resistance across each channel. Each module uses a 37pin DSUB connector on the front panel, as well as a 2x2 MicroFit connector for easy connection to a PXI Digital Multimeter(DMM).
-
Product
3 Ft Harness, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End
GT97102
-
3' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.
-
Product
Configuration Block For The 34934A Quad 4x32 Reed Matrix
34934C
Terminal Block
This configuration block provides flexible options for wiring rows and columns to D-Sub connectors.
-
Product
50-Pin D-Type Male Connector Block
92-965-050-M
D-Sub Male Connector Block
This connector block provides a simple method of connecting to 50-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
Product
SH37F-P-4, 37-Pin Female to Pigtail Shielded I/O Cable, 12ft
778620-04
Multifunction Cable
37-Pin D-SUB Female to 37-Pin Bare Wire Female, 12 ft, Pigtail I/O, Shielded Multifunction Cable - The SH37F-P-4 connects compatible CompactRIO modules to accessories or cables with bare wire connectors.
-
Product
36" Cable
RCONCEI-620
-
36" cable (with twisted pairs) transitions from a card end connector (P1 or P2) on the CEI-620, CEI-820 or RAR-cPCI to a 50 pin D-sub male connector.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 2 9-Pin Female D-Subs, for RS-422/485
540041010101
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 20", 2 9-Pin Female D-Subs
-
Product
Cable Assembly, Receiver, TriPaddle, 60", 37-Pin Female D-Sub
540016010901
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 60", 37-Pin Female D-Sub.
-
Product
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block
780041-01
Terminal Block
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block - The CAN Breakout Box works with high-speed, low-speed, and single-wire controller area network (CAN) devices or PC interfaces. It features 14 ports for connecting devices with cables or directly to wiring harnesses. With an onboard power supply, the CAN Breakout Box can place power on the V+ pin required by some CAN transceivers. With a switch on the front panel, you can select 120 Ω, 60 Ω, or no termination on the network. You can use the CAN Breakout Box in desktop applications or mounted on a DIN Rail for test fixtures and cabinets.
-
Product
CABLE ASSY, Type SH100-100-FLEX, 2 m
185095-02
Multifunction Cable
The SH100M-100M Flex Cable, sometimes referred to as SH100-100-F, connects NI digital I/O devices to 100-pin accessories with D-SUB connectors. The SH100M-100M Flex Cable is offered in different lengths.
-
Product
4-Pin Power D-Type Female Connector, 40A, With Backshell
40-960-004-F
D-Sub Female Connector
This connector is designed to allow users to directly terminate a cable with soldered connections.
-
Product
Connector Block, 50-Pin D-Type, Male
40-965A-050-M
D-Sub Male Connector Block
The 40-965A-050-M connector block provides a simple method of connecting to 50 Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
Product
TCS Comfort
-
Maschinenbau Haldenwang GmbH & Co. KG.
Trip distance / tachograph meter integrated into the brake tester (only in conjunction with PC)Electronic control unit TCS shockproof (workshop-oriented) aluminum housing with connection D-Sub 25p / D-Sub 9pEntire operation via integrated time and data display, and your existing PC (OS: Windows).Complete measurement and programming of the tachograph types 1311, 1314, 1318, 8400, FTCO 1319 MTCO 1324, TVI 2400, SE 5000, EFAs, SmarTach, DTCO 1381 incl. Integrated dial measurementLCD 4 rows, 16 digits; backlit with an integrated smart card readerMobile and / or stationary usable instrument; used stationary as integrated into the brake tester and the computer; optionally a road measurement is possible.Expression of complete test reportData storage for customer and vehicle datamultilingualism
-
Product
Video Signal Distributor
MSVD-250N
-
MSVD-250N is a Analog Distributor Buffer that distribute one (1) input signal to the 5/10/15/20 channels. User can select input type between 15P D-Sub and 5 BNC (R,G,B,HS,VS). The distribution buffer can be used in factory assembly lines, repair depots, and for system integration to save cost and time.
-
Product
8 Pin Power D-Type Female Connector, 40A, With Backshell
40-960-008-F
D-Sub Female Connector
This connector is designed to allow users to directly terminate a cable with soldered connections.
-
Product
Solder Cup Connector Kit
Y1140A
-
Used to build custom cables for 34922, 34924 – 78-pin Dsub female – 60 V
-
Product
Digital Cable
Digital Cable
The Digital Cable models include a variety of industry-standard front- and back-end connectors, such as 68-pin VHDCI, 68-pin D-SUB, and flying lead options. Some models can connect digital instruments with other accessories to break out cable signals for direct access. Others provide flying leads that plug directly into any 0.1 in. header connector.
-
Product
1.5-m, 78-pin Dsub Cable
Y1137A
Switch Cable
The Y1137A is a M/F twisted-pair cable with outer shield. The 300-V cable provides a direct connection for the Keysight multifunction switch / measure mainframe and modules. Some modules require two cables.
-
Product
24-Channel Digital I/O With Digital Integration Features On M.2
M.2-DIO-24A
-
The M.2-DIO-24A is an M.2 card, and optional cable assembly (D-Sub 37-pin Male connector) designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program. This also allows for simple and trouble-free migration from other ACCES PCI and PCI Express digital I/O cards, but also provides for advanced features enabled by the onboard FPGA logic.
-
Product
37-Pin D-Type Female Connector Block
40-965-037-F
D-Sub Female Connector Block
Suitable for use on the front of modules this connector block provides a simple method of connecting to 37-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
NI CAN Cable, No Term, High-Speed/FD/Low-Speed, D-Sub 9-Pin F, 1m
193128-01
-
9-Pin Female D-SUB to 9-Pin Female D-SUB CAN Cable - The DB9F-DB9F CAN Cable connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules to devices, breakout boxes, and accessories. It is sometimes referred to as CAN Cable (single termination or no termination). This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals, available with or without termination, and in different lengths.
-
Product
SHC68-68-EPM Shielded Cable, 68 D-Type to 68 VHDCI Offset, 10m
192061-10
Multifunction Cable
68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair, Shielded Multifunction Cable - The SH68M-68F-EPM Cable, sometimes referred to as SHC68-68-EPM, connects DAQ devices to accessories or cables with D-SUB connectors. You can use this cable to create custom cabling for your DAQ device. The SH68M-68F-EPM Cable is offered in different lengths.
-
Product
64-Channel Form A General Purpose Switch for 34980A
34939A
General Purpose Switch
The Keysight 34939A is a high density general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 64 independent single-pole, single-throw (SPST) relays that can switch 1A and carry 2A. This module can be used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The relays are 100V, 1A contacts and can handle up to 60W. Standard 78-pin Dsub connectors allow for use with standard cables, screw terminal blocks, or mass interconnect solutions.
-
Product
SHC68-68-EPM, 68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair, Shielded Multifunction Cable, 0.5m
192061-0R5
Multifunction Cable
Connects to DAQ devices and modules, terminal blocks, bare wires, or other accessories. The multifunction cable models include a variety of industry-standard front- and back-end connectors, such as 68-pin VHDCI, 96-pin SCSI, and 68-pin SCSI. Cable selection depends on the connector types and requirements of the hardware you’re connecting to and the environment in which you’re using the cable. Some cables are internally twisted and shielded to more effectively reject ambient noise than an ordinary shielded cable. These cables are designed to work with high-performance NI devices.
-
Product
Cable Assembly, Receiver, TriPaddle, 36", 44 Pin ML DSub, (2) SMB Plugs, Twisted Pair
540149050201
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 36", 44 Pin ML DSub, (2) SMB Plugs, Twisted Pair.
-
Product
Cable Assembly, Receiver, TriPaddle, 48", 37-Pin Female D-Sub
540016010601
Cable Assembly
Cable Assembly PXI / VXI 6 BNC 48"
-
Product
High Density Switches
-
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
