Phase Noise Analyzers
-
Product
Phase Noise Analyzers
-
Holzworth Instrumentation, Inc.
Holzworth's Real Time Phase Noise Analyzers are each designed to provide data faster than any other system, while maintaining data accuracy and repeatibilty. There is no guess work as to whether results are valid to the DUT or if there are unwanted variations or contributions coming from the measurement system itself.
-
Product
Phase Noise Analyzers
-
The phase noise analyzer portfolio from Rohde & Schwarz offers an affordable, mid-range solution with high sensitivity and fast measurements as well as high-end ultra-high-sensitivity solutions with advanced measurements modes. Ideal for phase noise analysis and VCO tests, the industry-leading solutions enable two-path phase noise analysis with real-time cross correlation and fast VCO characterization with built-in low-noise DC sources. Additionally, high-end signal and spectrum analysis can be added into a single box.
-
Product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
-
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
Product
Phase Noise Generator / Calibrator
PNG-A
-
Noise eXtended Technologies S.A.S.
The PNG-A is a high precision generator used in Test and Measurement instruments calibration. It is a Signal Generator with precisely computed phase and amplitude noise characteristics. With its wide frequency offset range, 1Hz to 1 MHz offset, and its programmable Phase and Amplitude noise in real time, this is the ideal standard to calibrate phase noise analyzers, Signal Source Analyzers and Spectrum Analyzers.
-
Product
Hi-Q W-Band Ultra Low Phase Noise Analyzer
OE8000W
-
HI-Q® W-Band phase noise test system utilizesmicrowave photonics techniques for automatedmeasurement of ultra-low phase noise W-bandoscillators.
-
Product
The All-In-One Noise Test System
NXA Series
-
Noise eXtended Technologies S.A.S.
The NXA is a fully automated Phase Noise analyzer. Its dual channel architecture allows the system to use a cross-correlation process to cancel its internal noise floor. This reliable technique provides access to the unique noise floor performance of the DCNTS.
-
Product
Phase Noise Analyzer
DCNTS
-
Noise eXtended Technologies S.A.S.
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences.
-
Product
Phase Noise Analyzer and VCO Tester
FSWP
Phase Noise Analyzer
The R&S®FSWP phase noise analyzer and VCO tester features very high sensitivity thanks to extremely low-noise internal sources and cross-correlation. It can measure phase noise and amplitude noise in mere seconds on highly stable sources such as those in radar applications. Additional options such as pulsed signal measurements, residual phase noise (including pulsed) characterization and integrated high‑end signal and spectrum analysis make the R&S®FSWP a unique test instrument.
-
Product
Phase Noise Analyzer
NXA-50
-
This new NXA-50 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 50 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range.
-
Product
Phase Noise Analyzer
NXA-6
-
This new NXA-6 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 6 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range.
-
Product
Phase Noise Analyzer
NXA-26
-
This new NXA-26 is a sea-change in Phase Noise Test Systems. Making both residual and absolute noise measurements out to 26.5 GHz, this self-contained instrument uses either internal or external references with cross correlation for maximum dynamic range. The NXA-26 combines over 25 years of Phase Noise Measurement Technology with an easy to navigate user interface. System operation requires minimal training that will have you making measurements in minutes.
-
Product
Phase Noise Analyzer and VCO Tester
FSPN
Phase Noise Analyzer
The R&S®FSPN phase noise analyzer and VCO tester is designed to provide both very high sensitivity and measurement speed for production and design engineers working in these fields characterizing sources such as synthesizers, VCOs, OCXOs, and DROs. It is the ideal instrument for demanding development and production phase noise and VCO analysis.
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 40 GHz
N8976B
Low-Frequency Noise Analyzer
The N8976B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8976B.
-
Product
Advanced Low-Frequency Noise Analyzer
E4727B
Low-Frequency Noise Analyzer
Get a deeper, closer look at low frequency noise with the A-LFNA integrated with WaferPro Express, featuring data analysis, wafer prober control and test suite automation.
-
Product
DC-Powered, Phase Sequence Monitor
PAD/PLD
Phase Sequence Monitor
NAI's PAD and PLD are DC-Powered, Phase Sequence Monitors that protect three-phase loads from damage due to phase reversals or phase absence. These sequence monitors are ideally suited for rugged defense and industrial applications.
-
Product
Millimeter-Wave Noise Source, R-band, 26.5 to 40 GHz
R347B
Noise Source
The Keysight R347B noise source covers a 26.5 to 40 GHz frequency range. This waveguide noise source allows you to make accurate and convenient noise figure measurements on millimeter-wave devices. The R347B provides highly precise broadband noise at the input of the system or component under test. The noise figure meter then processes the ON/OFF ratio of noise power present in the system IF, and provides an accurate reading of noise figure and gain. The R347B noise source has remarkable ENR stability over time, which allows longer recalibration cycles and more accurate noise figure measurements.
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 26.5 GHz
N8975B
Low-Frequency Noise Analyzer
The N8975B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8975B.
-
Product
Signal Integrity Studio, Analysis & Simulation SW for WAVEPULSER High-Speed Interconnect Analyzer
WavePulser-Signal Integrity (SI) Studio
Analyzer
WavePulser Signal Integrity (SI) Studio is included as a single license in the WavePulser 40iX-BUNDLE or can be purchased as an additional license for offline access to additional users. WavePulser Signal Integrity (SI) Studio combines S-parameter, Impedance profiling and de-embedding measurements, channel and equalizer modeling, eye diagrams and jitter analysis in a single affordable software package for emulating the complete serial data channel.
-
Product
Phase Angle Voltmeters
Phase Angle Voltmeter
Since the development of the first Phase Angle Voltmeter (PAV) over 50 years ago, North Atlantic Industries has been the industry leader in AC Measurement Instrumentation. Our name has become synonymous with innovation and quality. Our products, specifically designed for defense, industrial, and commercial applications, deliver industry-leading accuracy, repeatability, and reliability.NAI’s units of today are actually multifunction Digital Analyzing Voltmeters that combine a complete Voltmeter, a Phase Angle Voltmeter, and a Waveform Signal Analyzer in a single microprocessor-based instrument. With these versatile and flexible instruments, a wide range of tests can be performed, either manually using the front panel controls or automatically using the IEEE-488 bus. Designed for the Synchro/Resolver and LVDT/RVDT marketplace, NAI’s Voltmeters are used in a variety of applications.
-
Product
Noise Source, 1 GHz up to 50 GHz
346CK01
Noise Source
The Keysight 346CK01 is the ideal companion to Keysight´s noise figure solutions when working on high frequency applications. Since it is broadband (1 GHz to 50 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty, which are reflections of the test signals. This is a coaxial noise source with a 2.4 mm coaxial connector. ENR typically 20 dB at 1 GHz, decreasing to typically 7 dB at 50 GHz.
-
Product
Noise Source Test Set, 10 MHz to 26.5 GHz
N2002A
Noise Source
The N2002A noise source test set is a low cost, stand-alone instrument that, as part of a calibration system, enables fast, repeatable calibrations with minimal levels of uncertainty.
-
Product
High-Speed Digital Analyzer
HDA125
Analyzer
Plug in a high performance logic analyzer to your oscilloscope for enhanced visibility during mixed signal analysis. The HDA125 High-Speed Digital Analyzer supplies 12.5 GS/s sample rate and up to 18 leads in a small modular form factor.
-
Product
Noise Figure Analyzer, Multi-touch, 10 MHz to 3.6 GHz
N8973B
Low-Frequency Noise Analyzer
The N8973B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8973B.
-
Product
Bus Analyzer Software
AltaView
Analyzer
Alta’s Windows avionics analyzer product, AltaView, provides the most modern technologies for MIL-STD-1553 and ARINC-429 network activity and data analysis. Win XP/Server/7/8/10 Compatible and VMware with ENET/NLINE Ethernet. Ideal for Cybersecurity Testing.
-
Product
Portable Bus Analyzer
1553
Analyzer
Our new inline Bus Monitor is a very small, very light MIL-STD 1553 Bus Monitor that can be connected to any Windows device with a USB connector. It monitors and records all or selected 1553 traffic for later analysis or reconstruction in the lab.
-
Product
Ultra-Low Noise Filter, 42 V / 105 MA, 50 Ω
N1298B
Noise Filter
The N1298 Series is a collection of low noise filters for the Keysight B2960 Series 6.5-digit low noise source.
-
Product
VHF/UHF Airnav/Com Analyzer
EVSG1000
Analyzer
The R&S®EVSG1000 is a portable signal level and modulation analyzer specifically designed for commissioning and servicing ILS, VOR and marker beacon ground stations and for analyzing ATC COM signals.
-
Product
USB 2.0 Protocol Analyzer
Mercury T2
Protocol Analyzer
The Mercury T2 is the industry's smallest, most affordable hardware-based USB 2.0 protocol analyzer that combines the defacto standard CATC Trace display with powerful analysis features. The pocket-sized Mercury T2 is bus powered and is controlled using any Windows PC. With comprehensive triggering, the Mercury T2 provides much of the same lab quality protocol analysis capabilities offered in Teledyne LeCroy's top-of-the-line USB analyzers.
-
Product
PCIe 3.0 Protocol Analyzer
Summit T3-16
Protocol Analyzer
The Summit T3-16 is Teledyne LeCroy's fifth generation of protocol analyzers targeted at high speed PCI Express I/O-based applications such as workstation, desktop, graphics, storage, and network card applications.
-
Product
Spectrum Analyzer
FPC
Spectrum Analyzer
Outstanding quality and innovation does not have to come with a high price tag. The R&S®FPC spectrum analyzer provides unexpected performance at a budget-friendly price. It is engineered in Germany and designed to the same quality standards as highend instruments.
