Simulators
create what could be.
See Also: Simulation, Simulation Software, Simulation Testing, Emulators
-
Product
AC Load Bank (Resistive & Inductive)
K-1000 Resistive & Inductive
-
Kongter Test & Measurement Co., Limited
Kongter resistive & inductive AC load banks are used to simulate the motor loads or other electromagnetic devices working at their rated power factor. Many backup generators and turbines are rated at 0.7, 0.8 or 0.85 power factor and need to be commissioned at nameplate capacity using a combination of resistive and reactive load to fully qualify their operating capability. Using a resistive & reactive load bank enables comprehensive testing from a single unit.
-
Product
4, 8, 16 And 32 ChannelARINC429 Test And Simulation Modulefor PCI Express
APE429-x
Simulator
ARINC429 Test and Simulation modules with 4, 8, 16 or 32 Software programmable Tx/Rx channels plus up to 8 Discrete I/O’s. The APE429-x is a functional replacement for the models API429-x/APX429-x.
-
Product
PXI Resistor Module 2-Channel 2R to 16.3k with SPDT
40-293-131
Programmable Resistor Modules
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI High Density Precision Resistor Module, 3-Channel, 3.5Ω to 201kΩ
40-298-141
Programmable Resistor Modules
The 40-298-141 is a high density programmable resistor module with 3 channels which can be set between 3.5Ω and 201kΩ with 0.25Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Traveling Wave Tube Amplifier
-
Skylink a leading provider in design and manufacture a wide range of traveling wave tube amplifiers(TWTAs) and microwave power modules(MPMs).Skylink's new generation of MPMs are based on a modular design, and use new technology, material and computer simulation system to improve weight, size and efficiency.Our main MPM series frequency covers range from 2 to 40GHz and providing more than 100W. They combine a helix TWT, a solid state amplifier and an integrated power conditioner in a compact package.
-
Product
Battery Crush Nail Penetration Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL battery crush nail penetration tester is used to simulate the use, transportation, storage and disposal of various types of batteries under certain temperature conditions, when the battery is crushed (such as compacted garbage) or nail penetration, and to judge the battery safety performance. The battery is qualified as no disintegration, no rupture, and no fire.
-
Product
Servo Computer Battery Crush Tester
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Servo Computer Battery Crush Tester simulates the situation in which various types of lithium batteries are squeezed during use. Artificially present different conditions that may occur when the battery is squeezed.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm - SPST
50-294-132
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI-8516, 2-Port, PCI, LIN Interface Device
781365-01
LIN Interface
2-Port, PCI, LIN Interface Device—The PXI‑8516 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The PXI‑8516 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time for processing complex models and applications.
-
Product
Loading Devices
-
Educated Design & Development, Inc.
Sometimes you may need additional loading for abnormal testing (i.e. overload test). Other times, you may need additional loading to simulate worst case normal operation conditions (i.e. input test, temperature test). No matter what your application, we have the loading device to fit your needs! TECH NOTE: Be sure to request our outline titled "Selecting Loads" for assistance in determining the proper rated device for your application.
-
Product
Panel-mounted Voltage Power Amplifier
PAV120Bi
-
PAV120Bi is specially designed for R&D of power system simulation. It is adapt to various capacitive and inductive load. It is with 6 channels voltage outputs, each channel with 120V/60VA maximum output.
-
Product
PXI High Density Precision Resistor Module, 6-Channel, 4Ω to 1.51MΩ
40-298-050
Programmable Resistor Modules
The 40-298-150 is a high density programmable resistor module with 3 channels which can be set between 4Ω and 1.51MΩ with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Trimble Hydrographic Extensions
SCS900
-
Users of Trimble Construction SCS900 software are now able to easily measure water depth and execute accurate small-scale hydrographic surveys. Ohmex Ltd has made use of the SCS900 Software Developers Kit (SDK) to produce a software utility that runs on the controller and supplies depth data to SCS900. This increment in functionality further enhances the use of the SCS900 system on marine construction sites where dams or waterways are present.The concept of the Sonar extension to SCS900 is to enable the construction user to execute simple Hydrographic surveys using their SCS900 software together with existing positioning equipment, no need to learn another package or convert to new reporting facilities, the sonar effectively behaves as an extension to the existing survey detail pole for measuring water depth. The software is an inter-application package with both the SCS900 and SonarMite applications running concurrently on a TSC2, Tablet or PC platform. For evaluation purposes the SonarMite application has a 'Simulator' mode that generates sine wave data without the need for a SonarLite echo sounder to be connected ...
-
Product
Solar Simulator
-
Excellent reputation for its high degree of throughput, accuracy and stability. Pulsed light is used, ensuring stable measurement.Approximates the spectral distribution of AM 1.5G reference solar radiation. Achieves accurate measurement of various modules.No need to reverse modules, facilitating in-line operation.
-
Product
Mini PCI Card
EXC-1553mPCIe/P1
-
This card’s small size and suitability for Mini Card compatible computers make it a complete solution for developing, testing, integrating 1553 interfaces and for performing system simulation of the MIL-STD-1553 bus, both in the lab and in the field.
-
Product
MIL-STD-1553 A / B Test And Simulation PC / 104+ Module
PC104p-1553
-
*Dual redundant*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems*Supports ARINC429 and ARINC 664 operations
-
Product
Digital And Analog Call Simulation
-
GL’s T1 E1/Analog Test Suite supports analysis and emulation of legacy protocols (MFCR2, E&M, SS1/SS4, SS5, Voice Call Signaling, 2-wire Call, SF Signaling (DTMF)) applicable to Federal Aviation Administration "FAA" within their National Airspace System "NAS" Ground-to-Ground Air Traffic Control Network and Voice System (NVS) to Analog Interphone.
-
Product
PXI-2720, 8-Bit, 10-Channel PXI Programmable Resistor Module
781985-20
Programmable Resistor Modules
8-Bit, 10-Channel PXI Programmable Resistor Module—The PXI‑2720 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2720 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
Product
PCI-7811, 1M Gate Virtex-II FPGA, Digital Reconfigurable I/O Device
779363-01
Digital I/O
The PCI‑7811 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. The PCI‑7811 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, custom communications protocols, bit error rate test, and other applications that require precise timing and control.
-
Product
Xenon Test Chamber
-
Xi'an LIB Environmental Simulation Industry
Designed to be accelerate the weathering and aging process by simulating exposure to sunlight.
-
Product
DG Test Panel for C-14/A/D Gyros
TA-14
-
C-14 Gyro Series DG panel. This special test panel does include a FV simulator for a more complete solution to stand alone gyro testing.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 65.5k Ohm - SPST
50-294-133
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Intelligent Interface Card
IIB-1553-ISA
-
The IIB-1553-ISA is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for PC compatible computers, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-ISA supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multilevel triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. PC memory space utilised by the board is selectable.The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Product
SCRAMNet GT200
-
Curtiss-Wright Defense Solutions
SCRAMNet Network products have provided an model data communications solution for simulation, virtual reality and other real-time applications with critical performance requirements for more than two decades.
-
Product
6″ (15.25 cm) 1000W Pre-Irradiation Solar Simulator
Model LS1000-6S-009
-
1000W Pre-Irradiation Solar Simulator Kit specifically designed for the pre-irradiation step during in vitro broad spectrum sunscreen testing. Fully compliant with the most current FDA and ISO requirements. The 6″ (15.25 cm) Class A beam can irradiate up to 9 PMMA plates simultaneously.
-
Product
PXI/PXIe High Density Precision Resistor Module, 4-Channel, 1.5 Ω to 925 Ω
40-297A-121
Programmable Resistor Modules
The 40-297A-121 (PXI) and the 42-297A-121 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 925 Ω, 0.25 Ω Resolution. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
ARINC825 Cards
-
AIM’s ARINC825 cards can work either with full functionality as an active CAN node for testing and simulating or in listening only mode for monitoring and recording purposes of Avionic CAN bus (ARINC825) applications on up to 4 electrically isolated CAN bus nodes concurrently. All nodes are in conformance with the ISO11898-1/-2 standard. They are accessible by software separately and can be used as 4 independent CAN bus nodes. An onboard IRIG-B time decoder allows users to accurately synchronize single or multiple modules to a common time source. All supported signals are available through front I/O and rear I/O interface. ARINC825 cards consist of FPGA based CAN interface controllers as well as a FPGA based 32-bit microcontroller core and a separate processor for IRIG-B synchronization with high resolution time stamping. All nodes are operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s with the intelligence to process scheduling of CAN frames in real time onboard to significantly off-load the host processor.For embedded applications the AMC825-4 PMC module is available in a conduction cooled version. Using AIM’s family of PCI, CPCI (3U and 6U) and VMEbus carrier cards for PMC our clients have off the shelf solutions in a broad range of card formats. ARINC825 (CAN bus) modules are delivered with an Application Programming Interface (API) and Driver Software compatible with Windows, Linux and VxWorks.An ARINC825 Resource Component is available for AIM’s PBA.pro™ databus test and analysis tool including Tx and Rx simulation capabilities, a Chronological Bus Monitor and support for decoding of payload data within CAN messages. This allows to implement a powerful ARINC825 (CAN bus) analyzer or a complete test system in conjunction with other AIM avionics databus interfaces and PBA.pro™ supported 3rd party hardware.
-
Product
MIL-STD-1553 MCH
M4K1553MCH
-
The M4K1553MCH interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.The M4K1553MCH contains 32k x 16 of dual-port RAM for Data blocks, Control registers, and Look-up tables. All Data blocks and Control registers are memorymapped and may be accessed in real time. The dual-redundant 1553 module may be programmed to operate in one of four modes of operation: Bus Controller, Remote Terminal, RT/Concurrent-Bus Monitor, and Bus Monitor. The M4K1553MCH comes complete with Windows software, and a C driver software library including source code.
-
Product
PCI Strain Gauge Simulator Card, 6-Channel, 1k
50-265-206
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Interface
RP-708
Interface
The RP-708 is a two-channel ARINC 708 weather radar display data bus PMC module interface, supporting variable frame sizes for embedded applications, simulation and test. Abaco Systems provides integrated support for this module on PCI, PCIe, CompactPCI, VME, VXI and native PMC platforms. Each RP-708 channel can be configured as two transmit channels, two receive channels, or one transmit channel and one receive channel simultaneously.
