Visual Inspection
See Also: PCB Inspection
-
-
Product
High Precision Angular Position, Calibration and Geometry Inspection
GeoOrdinate
-
Rotary Precision Instruments UK Ltd
Ultra precise rotary tables intended for fine inspection, metrology and test applications.The GeoOrdinate has been designed specifically for the inspection of large and heavy components and is fully compatible with any shop floor environment whilst maintaining world class accuracies more commonly seen in the standards laboratory.
-
Product
Solder Past Inspection
-
From the innovative Z-Check 3D through to the entry level Z-Check 100 the entire range has been designed to provide accurate pad specific measurement of solder paste deposits, adhesives and component placement. Amongst its other features the Z check software comes with the convenience of a full SPC package as standard.
-
Product
Analog Ultrasonic Inspection System
ULTRAPROBE 100
-
The Ultraprobe senses high frequency sounds produced by operating equipment, leaks and electrical discharges. It electronically translates these signals by heterodyning them down into the audible range so that a user can hear these sounds through a headset and see them as intensity increments on the meter. Heterodyning works the same as a radio in that it accurately transforms the sounds so that they are easily recognized and understood.
-
Product
Sensor for Filament Inspection
EyeFI
-
EVT presents the EyeFI - the sensor for the inspection of filaments. The sensor contains two cameras with an Aptina sensor and S-Mount lenses. The cameras are perpendicular to each other. It is therefore possible to inspect two sides of the filament, which means that the EyeFI can detect if the filament is out-of-roundness. Additionally the errors and defects can be detected. For example the occurring flaws are point-shaped or partly flaked, or point-shaped and transverse, or also looking like a longitudial rib, or only spots in different shapes. The defects can be detected with the EyeFI sensor. The EyeFI contains board cameras with sensors from Aptina, the IoCap and an evaluation processor. The housing is about 14x10x4 cm in size. The IoCap is the image-capture-IO-board, which is designed and developped by EVT.
-
Product
Verification And Print Quality Inspection Solutions
-
Integrate quality barcode verifiers within your production line using our robust barcode verification technology.
-
Product
Magnetic Particle Inspection
NDT
-
DCM Tech offers a comprehensive selection of Magnetic Particle Inspection machines for non-destructive testing (NDT). Easily and quickly detect internal and subsurface damage on critical parts. Contact DCM to speak to your regional Technical Specialist about adding an MPI to your shop.
-
Product
Digital Inspection Camera
MaxiVIDEO MV108S
-
It turns your Autel tablet into a video inspection scope, allowing you to examine difficult-to-reach areas hidden from sight. It is capable of recording digital still images and videos. Includes mirror, hook and magnet attachments.
-
Product
Inspection Instrument for Indicators
i-Checker
-
The i-Checker is specially designed to calibrate measuring accuracy of dial indicators, dial test indicators, and other electronic comparison gage heads with a stroke of up to 100mm (4").±(0.2+L/100)µm indication accuracy. Directly inspects an indicator with a stroke of up to 100mm (4"). The dial test indicator, bore gage and lever-type inductive head can be inspected with optional accessories. Adjustment of the measurement position is very easily accomplished because of semi-automatic measurement and full automatic measurement functions. Creates and prints out the simple inspection certificate. Saves inspection result as CSV file for reusable inspection result by any kind of software.
-
Product
GENERAL INSPECTION MACHINE AFTER SOLDER MASK
-
DVI is a technology of automated optical inspection, which can inspect deep to the difference from semi-transparent layers or semi-reflective layers.
-
Product
Surface Defect Inspection System
-
Wafer for inspection of surface condition of specular flat substrate, glass substrate, others φ 100 ~ φ 300 compatible
-
Product
Mobile ASA-Livestream Data Node for Main Inspection
CONNECT CUBE V3 | VP 185076
-
Maschinenbau Haldenwang GmbH & Co. KG.
The mobile data node is the right tool for quick and digital diagnosis of the brake system as well as for routine testing and calibration of all ASA livestream-capable brake testers. The plug & play solution can also be used for modern routine testing and calibration of brake test stands.
-
Product
Wafer & Die Inspection
-
SemiProbe wafer inspection system (WIS) examines, locates and identifies defects created during wafer manufacturing, probing, bumping, dicing or general handling. This provides microelectronic device manufacturers with accurate, timely quality assurance and process information. The WIS has single sided and double sided wafer mapping capabilities and can improve efficiency, reduce manufacturing costs, increase yields and shorten time to market.
-
Product
Backplane Profiling & Inspection System
603d
-
A major problem in the backplane industry is detecting bent connector pin defects. The most difficult being when the pin bends underneath the shroud rather than going into the hole. Many times this defect cannot be detected electrically as the connector pin is touching the conductive annular ring of the hole, allowing electrical test to pass. Unfortunately, it is an intermittent connection and will fail later on as there is not an actual mechanical connection.
-
Product
Macro Inspection
-
High-throughput automated macro inspectionAny wafer size, in less than one second with ~75 micron resolutionSmall footprint table-top system
-
Product
Inspection Toolkit
OTK-4000
-
The Inspection Toolkit contains selected tools for verifying the existence of threatening electronic surveillance devices.
-
Product
CT Inspection System
FF35 CT
-
The YXLON FF35 CT computed tomography system is designed to achieve extremely precise inspection results for a wide range of applications. Available in a single or dual tube configuration, it is perfect for very small to medium size parts inspection in the automotive, electronics, aviation, and material science industries.
-
-
Product
PosiTector Inspection Kits
-
PosiTector Inspection Kits contain a PosiTector gage body (Standard or Advanced) and 3 probes – coating thickness, environmental and surface profile, as well as, accessories in a convenient hard shell carrying case.
-
Product
Automated Optical Inspection System
506
-
We are proud to introduce the latest member of our model 505 AOI product family, the 506. This system was developed to provide a high coverage, easy to program AOI system for the larger backplanes / backpanels being produced today.
-
Product
Laser Sherography NDT Sensor for Post-Production Quality Control or In-Field Component Inspections
FlawExplorer
-
The FlawExplorer is a laser shearography NDT sensor designed to be used for post-production quality control applications or in-field (in-service) component inspections. Depending on the application, the sensor can be configured with thermal or vacuum (partial) excitation systems and may also be automated. It incorporates the very latest in phase-shifting technology delivering accurate and reliable measurement results through clear and sharp imaging with sub-micrometer displacement resolution.
-
-
Product
Reel to Reel Non-Contact OS Inspection System for TAB/COD/TCP/TBGA
TRV
-
*Most suitable mechanism for non-contact inspection*Sprochet-less transfer decreases products damage.*Easy operation by Fixture alignment mechanism*Equipped with Tracing Test function
-
Product
Foreign Matter Inspection Device For FPDs
HS-930
-
By adopting our original optical technology, we achieve an inspection speed of about 30% up (compared to HS-830). Improved the front / back judging ability to thin substrates.
-
Product
Packaged Food X-ray Inspection System
EPX100
-
Our revolutionary new x-ray system is so advanced it will not only improve your product safety and meet regulatory compliance but also will optimize and streamline your product inspection.
-
Product
Thickness and Flaw Inspection
OmniScan SX
-
Olympus is proud to introduce the OmniScan® SX, a flaw detector that benefits from more than 20 years of phased array experience and shares the OmniScan DNA. For improved ease of use, the OmniScan SX features a new streamlined software interface displayed on an 8.4 in. (21.3 cm) touch screen. A single-group and non-modular instrument, the OmniScan SX is easy to operate and cost-effective for less demanding applications.
-
Product
Fiber Optic Inspection
-
Optical Wavelength Laboratories
A dependable connector endface inspection scope is a vital part of any fiber optic professional’s tool kit. Inspecting patch cord connector endfaces before attaching them to equipment or patch panels saves time and effort, and ensures a clean, quality connection. These 400x video inspection scopes allow users to view connector endfaces on a PC or laptop screen, preventing harmful invisible light from entering the users eye, and ensuring maximum eye protection.
-
Product
Visual Analysis of any Embedded System
SystemView
-
SEGGER Microcontroller GmbH & Co. KG
SEGGER is announcing the release of SystemView, a free tool enabling the visual analysis of any embedded system. SystemView gives complete insight into the behavior of a program, with minimal side effects on the observed embedded system. SystemView offers cycle accurate tracing of interrupts and task start stop as well as task activation and API calls when an RTOS is used. It visualizes and analyzes CPU load by task and interrupts and scheduler. Test setups with LED and oscilloscope are a thing of the past.
-
Product
Pinhole Detection Inspection Kit
Elcometer 270
-
The Elcometer 270 Pinhole Detectors Inspection Kit utilises the wet sponge technique and has been designed to set a new standard for wet sponge detectors - a high quality, low voltage detector with similar accessories to a high voltage spark tester.
-
Product
In-Process Wafer Inspection System
7945
System
Chroma 7945 wafer chip inspection system is an automated inspection system for pre and post diced patterned wafers. Change kits enable switching between various applications by allowing different carriers including metal frame or grip ring.
