Battery Electrical
-
Product
Programmable Electrical Rule Checking tool
Calibre PERC
-
Calibre® PERC™, Mentor Graphics'' newest reliability verification solution is designed to address your advanced circuit verification needs for electrostatic discharge (ESD), electrical overstress (EOS), signals crossing multiple power domains, advanced ERC and other reliability concerns.
-
Product
Electricity Meters Tester
Caltest 10
-
Calmet Smart Calibration Devices
Single phase portable electricity meters tester class 0.5% powered from tested circuit with load force possibility apart from tested object. There is no need to disconnect the users during measurement
-
Product
Digital, Hand-Held, Battery Operated Meter
CM-2
-
The Camera Master II is a digital, hand-held, battery operated meter that measures six different characteristics of any video signal. Use it for fast and accurate set-up of any video source.
-
Product
Dual channel portable lightweight battery charger
TS2X020
-
The TS2X020 is a portable lightweight battery charger intended for rapid charging of vehicle batteries in the field without the attendant weight penalties usually associated with the operation. The charger is a constant voltage unit, and the charging current is regulated by the battery terminal voltage, with current limit of 20 Amps on 24v output, and 40 Amps on 12v output. Switch mode technology provides high efficiency; both in power to weight ratio, and input to output ratio.
-
Product
EIS Battery Analyzer
BA8100
-
The BA8100 is designed to accurately measure the internal impedance of a single cell or battery stack with voltages as high as 80 V. In addition to impedance, auxiliary measurements include voltage, current, phase, capacitance, inductance, quality factor and more. With the provided software, the BA8100 can perform Electrochemical Impedance Spectroscopy (EIS) across a frequency range of 50 mHz to 10 kHz. The impedance spectrum can be evaluated through the Nyquist and Bode plot tools to determine effective series resistance (ESR) and track battery health. Included with the BA8100 is a self-test fixture to verify the instrument’s performance or compensate for resistance introduced by the test leads.
-
Product
Electrical measurements
-
Instruments for measurement and analysis in accordance with the regulations of single / triphasic low voltage networks and data networks via cable or fibre.
-
Product
Electric Servo Motor Type 2 Axis Switching Simultaneous Vibration Tester
-
It is a 2-axis switching vibration tester and a 2-axis simultaneous vibration tester that mounts an electric servomotor actuator on the vibration drive unit.
-
Product
Field-installation Type Electric Conductivity Meter (Four-Wire Transmission, For High-concentration)
HE-200H
-
HE-200H connects conductivity sensor (FES-125F,126F) and measures conductivity and temperature in the sample water. It can be used not only for measurement of electrical conductivity in aqueous solution, but also for concentration adjustment and rinse monitoring of CIP, etc., as well as for concentration monitor of process.
-
Product
Miniature, Battery Powered, Stand Alone Pressure and Temperature Data Logger
PRTemp101A
-
The PRTemp101 is a miniature, battery powered, stand alone pressure and temperature data logger. This is an all-in-one compact, portable, easy to use device that will measure and record data for up to 8,191 measurements per channel. The storage medium is non-volatile solid state memory, providing maximum data security even if the battery becomes discharged.
-
Product
Testing Electric Pump Motors
-
This Custom Motor Test System is designed for the testing of 5 different sized electric motors used in various sump, utility, sewage, well, pool and pond pumps. All of the components mentioned above are mounted on a versatile table that can be easily reconfigured and retrofitted to any Magtrol dynamometer.
-
Product
Battery Discharger & Capacity Tester
IDCE-2415CT
-
Fuzhou Fuguang Electronics Co., Ltd.
IDCE-2415CT Battery Discharger & Capacity Tester
-
Product
Lithium Battery Inspection Tester
C19
-
Fuzhou Fuguang Electronics Co., Ltd.
C19 series is a portable tester which can quickly inspect battery pack of two-wheel vehicles. It can realize quick inspection and selection of SOH data of battery pack and discharge-charge maintenance. Data can be transferred to the mobile phone APP through Bluetooth forming a statistics report and faulty cell warnings so that further maintenance solutions can be developed in time.
-
Product
Multifunction Meter for Electrical Installations
AMPI-530
-
Measurement of short-circuit loop ; Testing of differential, general and selective protections for differential current ; Measurement of insulation resistance ; Up to 10GΩ ; Voltages: 50 V, 100 V, 250 V, 500 V, 1000 V ; Measurement of earth resistance ; Bi-directional continuity test on PE cables, phase sequence ; Measurement and recording of voltage, frequency, alternating current, cosϕ, power, harmonics and THD
-
Product
ECPR System (Electrically Calibrated Pyroelectric Radiometer)
Rs-5900
-
Developed in conjunction with NIST, the Rs-5900 ECPR is a ±1% absolute accuracy radiometric transfer standard for the visible to near-IR (0.25-2.0µm), with the RsIR Option extending the ±1% accuracy to >20µm. The RsP-590 Pyroelectric Probe requires no cooling and maintains ±1% accuracy from 1 µW to 100 mW. The ECPR uses an auto-nulling, electrical substitution technique that allows the instrument to be referenced against NIST electrical standards, insuring maximum accuracy and precision. Unlike most electrically calibrated radiometers, there is a direct correlation between electrical and optical heating because the same material serves as both the optical absorber and electrical heating element.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, 1 kV Isolation
41-752A-102
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Electrical Safety Testers- Hipots
-
Safety testers (also named hi-pot tester/hipot tester/hipot test) are designed to ensure safe operation of DUTs under various operating conditions and environment.GW Instek’s GPT-9900/GPT-9800/9600 series safety testers(hipot test) provide safe and quick measurement tools for AC/DC withstanding voltage tests, insulation resistance tests, and AC ground bond tests. Those tests are required by many international safety regulations such as CE, UL, VDE, and etc. We also have leakage current tester, GLC-9000, which supports all the major leakage current test standards for medical and general electronic equipment.
-
Product
Digital Electrical Network Analyzer
2126 NA
-
Standard Electric Works Co., Ltd
Microprocessor-controlled. Built-in earth tester. Built-in loop/psc tester. 0.03-2000Ω (software ctrl). Built-in voltmeter. Built-in wiring checker. One push button smart control. Display L-N and L-E voltages. 50 to 280Vac (sine). Display line path impedance. 0.01-2000Ω (software ctrl). Display earth path impedance. 0.01-2000Ω (software ctrl). Display neutral path impedance. 0.01-2000Ω (software ctrl). Display psc line to neutral. 6kA@230Vac supply. Display psc line to earth. 6kA@230Vac supply. Re-scroll through previous results. Bat. ok/low battery indicator. Auto off function. Color-coded test leads. Rugged case. Ultra low power consumption.
-
Product
Octal Small Form Factor Pluggable Electrical Interface
-
Eoptolink Technology Inc., Ltd.
Eoptolink is developing OSFP(Octal Small Form Factor Pluggable) a new pluggable form factor with eight high speed electrical lanes that will initially support 400 Gbps (8x50G or 4x100G). It is slightly wider and deeper than the QSFP but it still supports 32 OSFP ports per 1U front panel, enabling 12.8 Tbps per 1U switch lot. OSFP is designed to support the next generation of 800G optics modules that will use eight lanes of 100Gbps, and offers backwards compatibility with 100G QSFP.
-
Product
Battery Impedance Meter
-
Operation is fast and simple. Just press the spring-loaded probes onto the two poles of the battery. After 1.5 seconds, the unit beeps (indicating good contact) and displays the battery voltage and either the number of siemens or milliohms, depending on the knob setting. The display continues to show these numbers after the probes are removed; it resets only when the probes are pressed onto the next battery. The impedance and voltage of any battery between 1.2 and 60 volts can be read. Because of the wide range of voltages, even single low-voltage cells, such as NiMH, can be measured. The manufacturers of some batteries specify impedance in milliohms while other specify in siemens (one divided by the resistance in ohms). This meter will display both types of impedance for any given battery. Accuracy is +/- 2% of the value.
-
Product
Battery Tester
BAT-500
-
Amprobe BAT-500 Battery Tester quickly and accurately tests batteries without taking the batteries off-line. This Battery Tester features a comparator function with pass/fail indication, and speed testing of batteries up to 500 Ah. Amprobe BAT-500 Battery Tester, compact and light weight, simultaneously measures battery resistance and voltage up to 40 V.
-
Product
Battery Ground Detector
BGD
-
Battery Ground Detectors supply contact closures for alarm indications at precise ground fault resistance settings.
-
Product
Production Test Stands for Electric Motors
-
Electric drives such as DC and EC motors are more and more extensively deployed in the automotive industry. At the same time there is an increasing requirement for a 100% analysis of motors for fault detection and error analysis as well as statistics on quality, without increasing production cycles times. The model-based Parameter Identification method (PI method) from imc allows testing to be performed under load, yet without an “explicit” separate load machine. Instead, the motor is loaded dynamically by exploiting its own inherent inertia. This allows motor parameters such as resistance, inductivity and friction to be determined within a few seconds. A mathematical model and its parameters reflect motor behaviour in its completeness and make it possible to monitor motor production based on limit values and trend statistics. The identified parameters of the model equation can then be used to calculate derived key performance indicators of the motor characteristic curve.
-
Product
High-Performance All-In-One Gateway For Battery Energy Storage Systems
ECU-1170
Edge Gateway
Quad-core Cortex-A55 processor, 1.8GHzConnectivity: 4 GbE, 8 RS-232/485, 2 CAN, 1 mPCle and 1 M.2I/O: 20 DI, 6 DO, 8 Relay, 2 AIBattery-powered RTC, Watchdog, and optional TPM supportWide operating temperature range: -40~70°COptional 5 sec power backup with SupercapacitorSupports IEC 61850, IEC 104, DNP3, Modbus, MQTT, and OPC UAPreloaded with Yocto Linux and EdgeLink or Ubuntu Linux
-
Product
Lithium Battery Equalization Tester
LIFG
-
Fuzhou Fuguang Electronics Co., Ltd.
The LIFG series Tester is an intelligent and efficient lithium battery equalization maintenance instrument, which is used to quickly solve the problem that inconsistent voltage of lithium battery pack. Meanwhile it supports to make the voltage difference of any battery, which can be used for research and development experiments to stimulate what problems will occur when the battery reaches the maximum voltage difference under harsh work working conditions.
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF600
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensationof power factor in low voltage instalations.
-
Product
E-DRIV® Electric Screwdrivers
E-Series
-
The electric screwdriver is for light duty tightening applications. The assembly tool plugs directly into a power outlet and does not require a separate power supply unit. Ensures accuracy in fastening with precision automatic shut-off clutch once preset torque is achieved. Operates on a duty cycle of 0.5 seconds on and 3.5 seconds off.
-
Product
Digital Battery Tester with Automatic Test
706
-
Controlled by microprocessor, simply activate the switch once and the #706 applies a precisely timed, 10 second load to the battery. The test results, “OK”,“WEAK” or ”BAD” are then displayed along with the test voltage, until the unit is disconnected. The #706 also tests charging voltage and relative starter current draw.
-
Product
28/45 GHz Single Optical Channel and 50 GHz Dual Electrical Channel DCA-M
N1092C
Oscilloscope
High accuracy, low cost solution for optical and electrical waveform analysis including solutions for 8.4 through 64 GBaud, very low noise and jitter, and fast sampling rates for high throughput.
-
Product
Electric Vehicle Charger Testing
EV-TEST100
-
EV-TEST100 in combination with appropriate HT multifunction instrument simulates an electric vehicle connected to the charging station, allowing you to verify the EVSE full functionality and electrical safety. EV-TEST100 is able to test charging stations with charging modes 2 and 3 and Type 2 connector (European standard).
-
Product
Electrical And Optical Clock Recovery
Series Oscilloscopes
-
Provide clock recovery capabilities for optical and electrical NRZ and PAM-4 signals up to 64 GBaud with jitter spectrum analysis (JSA) and integrated variable equalizers advanced features
