ITA Modules
-
Product
PXI 8 Slot BRIC 120x16 1-Pole (8 sub-cards)
40-561A-121-120X16
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI/PXIe High Density 2A Multiplexer, 2-Bank, 64-Channel, 1-Pole
42-614D-010
Multiplexer Module
The 40-614D-010 (PXI) and 42-614D-010 (PXIe) 2-bank, 64-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI/PXIe High Density Precision Resistor Module, 4-Channel, 2 Ω to 13.6 kΩ
40-297A-131
Programmable Resistor Module
The 40-297A-131 (PXI) and the 42-297A-131 (PXIe) are 4-channel programmable resistors with a range of 2 Ω to 13.6 kΩ, 0.25 Ω Resolution. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
NI-9361, 32-Bit, 8-Channel C Series Counter Input Module
783407-02
Counter Input Module
32-Bit, 8-Channel C Series Counter Input Module - The NI‑9361 is a differential or single-ended input module. With this module, you can expand beyond the four counters in CompactDAQ to reach up to 64 counters per 8‑slot chassis. You can configure each channel to read a single pulse train or combine them to read up to four incremental encoders. You can also directly connect sensors with open-collector or push-pull outputs by using an internal switchable 1 kΩ pull‑up resistor. The NI‑9361 counters can perform encoder position and velocity measurements. You can synchronize the counters with other analog, digital, and counter measurements in your chassis.
-
Product
IO60-DIO48 Module
IO60-DIO48
Module
WINSYSTEMS’ IO60-DIO48 Module adds GPIO to embedded systems with IO60 expansion featuring 48 GPIO (General Purpose Input-Output) tolerant to 30 V DC. The SPI interface is implemented through the MACH XO2 SPI-slave EFB (Embedded Function Block) interface. Each bit of each port is implemented as a bi-directional tristate driver. Each bit of each port can also be configured and enabled to detect rising and/or falling edge events and generate a system interrupt.
-
Product
LXI 1GHz 75ohm 16x8 Matrix
60-731-003
Matrix Switch Module
The 60-731 is a family of integrated RF matrices suitable for use up to 1.5GHz. The construction of the 60-731 provides a cost effective alternative for RF switching based on microwave switching elements while maintaining a high level of matrix performance. The design is fully scalable, allowing a variety of matrix sizes to be offered in a single family.
-
Product
4-Slot BRIC, 256x8, 1Pole, PXI Matrix (4 Sub-cards)
40-559-401-256x8
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI 8 Slot BRIC 132x8 2A 1-Pole Matrix
40-567-103
Matrix Switch Module
The 40-567 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-567 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI High Density Precision Resistor Module, 4-Channel, 3Ω to 13.6kΩ
40-298-131
Programmable Resistor Module
The 40-298-131 is a high density programmable resistor module with 4 channels which can be set between 3Ω and 13.6kΩ with 0.25Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 4 Slot BRIC 32x12 2A 1-Pole Matrix
40-597-001
Matrix Switch Module
The 40-597 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 100VDC/70VAC. The 40-597 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-053
Programmable Resistor Module
The 40-297A-053 (PXI) and the 42-297A-053 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 11.4 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Modular and Scalable Multifunction Switch/Measure Units
EX1200 Series
Data Acquisition Module
The EX1200 product family is a modular and scalable series of multifunction switch/measure units that can be configured to address a variety of applications in the mechanical data acquisition and electronic test environments.
-
Product
20 Channel Actuator/GP Switch Module for 34970A/34972A
34903A
Switch Module
The Keysight 34903A is a general-purpose switch module for the 34970A/34972A Data Acquisition/Switch Unit. It has 20 independent single-pole, double-throw (SPDT) relays and is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Combine it with matrix and multiplexer modules to build custom switch systems. Its 300 V, 1 A contacts can handle up to 50 W, enough for many power line switching applications.
-
Product
PXI Very High Density Multiplexer, 198-Channel, 1-pole
40-670C-022-198/1
Multiplexer Module
The 40-670C-022-198/1 is a 198-channel, 1-pole MUX and is part of a series of very high density multiplexer modules featuring a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. The 40-670 multiplexer may be operated as a conventional multiplexer with break-before-make action when a new channel is selected. In addition multiple channels may be simultaneously selected (not available in 1 pole mode).
-
Product
LXI Optical Switching - 16:1 Multiplexer Plugin Module
65-281-314
Multiplexer Module
The 65-281-314 16:1 multiplexer is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
Product
PXI-2512, 7-Channel, 10 A PXI Signal Insertion Switch Module
778572-12
Signal Module
7-Channel, 10 A PXI Signal Insertion Switch Module—The PXI‑2512 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2512 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
Product
PXI Dual 4 to 1 Terminated RF Multiplexer 3GHz 50 Ohm MCX
40-873-102
Multiplexer Module
The 40-873-102 is a 4 to 1 RF MUX with 2 banks in a single PXI slot. Additionally, extra switching allows unused channels to be terminated into 50 Ohm, maintaining signal integrity. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
Product
COM Express Mini Size Type 10 Module with Intel Atom® x6000 Processors (formerly codename: Elkhart Lake)
nanoX-EL
Computer on Module
The ADLINK nanoX-EL is a COM Express Type 10 module that supports Intel Atom® x6000 (x6425E, x6413E, x6211E, x6200FE, x6425RE, x6414RE, x6412RE) as well as Intel® Pentium® and Celeron® N and J series processors (formerly Elkhart Lake) with integrated Intel® UHD graphics at a and high speed interfaces. nanoX-EL modules support LPDDR4 memory with in-band ECC up to 16GB, and are also available with rugged operating temperature range and low power envelope, making them a perfect match for mission critical fanless edge computing applications that require safety and reliability at all times.
-
Product
PXI RF Multiplexer: 3 GHz, 1 x 8, 50 Ω
M9148A
Multiplexer Module
Route signals up to 3 GHz through a 1 x 8 RF switch multiplexer in a single PXI module.
-
Product
LXI High Density 512x8 2-Pole 2A Matrix With BIRST
60-555-028
Matrix Switch Module
High density double pole matrix capable of switching up to 300VDC/250VAC, or 2A (60W max). The use of high quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
Product
PXI 4 Slot BRIC 116x6 2A 1-Pole Matrix
40-596-002
Matrix Switch Module
The 40-596 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 150VDC/100VAC. The 40-596 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI Monitored Multiplexer, Quad 16-Channel, 1-Pole
40-619-004
Multiplexer Module
The 40-619-004 is a high density PXI 2 A multiplexer module in quad 16-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
High-Density Matrix Switch Card
1260-43
Matrix Switch Module
The Astronics 1260-43 is a high-density matrix switch card. Each module consists of three 8x24 single-wire matrices, which are interconnected via a 10-lane, single-wire bus. On-board configuration relays allow software control of the matrix configuration.
-
Product
500 Watt Electronic Load Module
N3305A
Load Module
The Keysight N3305A is a 500 W (0-60A, 0-150V) electronic load module for use in either the N3300A or N3301A electronic load mainframe in system applications. The N3305A load module is fast and accurate, for programming in constant current, constant voltage, or constant resistance modes, or for making voltage, current or power measurements. The N3305A can also digitize waveforms.
-
Product
PXI 8-Slot BRIC Matrix, 2A 1-Pole 225x4, 3 Sub-cards
40-568A-103
Matrix Switch Module
The 40-568A-103 is a PXI 1-pole 225x4 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 300VDC/250VAC. The 40-568A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
Power Module, 100V, 3A, 300W
N6776A
Power Module
The Keysight N6776A is a 300 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
Switched Power Distributed Module, CAN Control
H730008xS
Power Module
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions: Distributing the power to each device in a system Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.
-
Product
LXI Optical Switching - 2x2 Matrix (Insert/Bypass) Plugin Module
65-280-360
Matrix Switch Module
The 65-280-360 2x2 matrix is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
Product
PXI High Density Precision Resistor Module, 9-Channel, 2.5Ω to 3.55kΩ
40-298-023
Programmable Resistor Module
The 40-298-023 is a high density programmable resistor module with 9 channels which can be set between 2.5Ω and 3.55kΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI 8-Slot BRIC Matrix, 55x16 1-Pole (5 sub-cards)
40-562B-121-55X16
Matrix Switch Module
The 40-562B-121-55X16 is a high density BRIC8 matrix module with a size of 55x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
