Analog Output Modules
-
Product
2x16 Channel Multiplexer
FXA-103 MUX 16×2
Multiplexer Module
The FXA-103 is a two times sixteen channel multiplexer which allows to route analog or digital input signals from multiple sources to one measurement device. To simplify control the corresponding relays of both multiplexers are switched together and each channel is equipped with a status led. In addition, it is delivered with an installed DIN rail carrier.
-
Product
Signal, Module, Receiver, QuadraPaddle, 90 Series, 192 Position, Fully Loaded with Twin Female Contacts and Round Posts (610138200 and 610138117)
510150137
Receiver Module
Primary mating module 510151105. (May mate with other ITA modules, as well.)
-
Product
NI-9476, 36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module
NI-9476 / 779140-01
Digital Module
36 V, 32-Channel (Sourcing Output), 500 µs C Series Digital Module - The NI‑9476 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 36 V, based on the external power supply, and features transient overvoltage protection between the output channels and the backplane. You can programmatically monitor the built-in overcurrent and short-circuit protection status of each channel.
-
Product
Analog Output Device
Analog Output Module
The Analog Output Device helps you create applications such as stimulus-response, power supply control, deterministic control, and sensor/signal simulation. The Analog Output Device supports various output resolutions, channel counts, and other onboard features, so you can replace several kinds of instruments in your system, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators.The Analog Output Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
PXI 3A Power MUX BRIC, 24-Channel, 6-Pole
40-571-403
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781774-03
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
COM Express Basic Size Type 6 Module with 11th Gen Intel® Core™, Intel® Xeon® and Intel® Celeron® Processors
Express-TL
Computer on Module
ADLINK’s Express-TL COM Express Type 6 Basic size module is based on the 11th Gen Intel® Core™, Xeon® W and Celeron® 6000 processor, and is the first COM Express module to support PCI Express x16 Gen4, effectively doubling the bandwidth of previous generation COM Express modules. With a combined 8 cores, 16 threads, and up to 128GB memory, the Express-TL brings uncompromised system performance and responsiveness to your solution. Featuring brand new Gen 12 Intel® UHD Graphics and Intel® AVX-512 Vector Neural Network Instructions (VNNI), the Express-TL provides AI inferencing performance as much as 3X higher compared to previous generation non-VNNI platforms. The integrated Gen 12 Intel® UHD Graphics core can be configured to support one 8K independent display or four 4K independent displays (HDMI/DP/eDP). In addition, legacy display interfaces such as LVDS and analog VGA are still supported as build options. Key features for today’s applications are support for 2.5 GbE and USB 3.2 with transfer rates of up to 10Gb/s that can transfer image data from cameras faster than previous generation products. Combined with 8 processor cores at 25W TDP, Intel® AVX-512 VNNI, Intel® OpenVINO™ toolkit and Intel® UHD Graphics, the Express-TL is well suited for AI at the edge applications (AIoT/IoT).
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 67 GHz, 50 Ω, SMA-1.85, Terminated, Failsafe
40-785C-472-T
Multiplexer Module
The 40-785C-472-T (PXI) and 42-785C-472-T (PXIe) are dual failsafe SP4T 67 GHz with automatic termination of unused signals. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
Signal Module, ITA, QuadraPaddle, 192 Position, Right Angle Contacts For Custom PCB Mounting (510 151 107 And 510 109 316)
510151121
ITA Module
This kit has everything you need to attach a VPC ITA Module to a custom designed PCB. This includes the right angle header (P/N 510 109 316) and the ITA Module (P/N 510 151 107).
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber, FC/APC Connectors
42-852A-018
Multiplexer Module
The 40/42-852A-018 is a PXI/PXIe 8-channel multiplexer with FC/APC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
MIC-780 series i-Module with 2 x PCIex8, 1 x PCIex4, 1 x PCIex2
MIC-78M40-01
Expansion Module
2 x PCIEx81 x PCIEx41 x PCIEx2Support 1 x 8cm FAN (Optional)Support additional 2.5" HDD/SDD kitDiemension with MIC-780 : 173 x 195 x 255 (mm)
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 3GHz, 50Ω, N-Type, Terminated
40-785C-561-T
Multiplexer Module
The 40-785C-561-T (PXI) and 42-785C-561-T (PXIe) are single SP6T 3GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI Solid State Multiplexer Module, Single 6-Channel, 30 A
40-667C-012
Multiplexer Module
The 40-667C-012 is a single 6-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXI 10A Power MUX 4-Bank 8-Channel
40-661-002
Multiplexer Module
The 40-661 is a single pole power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available. Signal connections are made via front panel mounted 20-way GMCT plugs.
-
Product
PXI 2 Banks of 40 Channel 1 Pole MUX
40-615-021-2/40/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 18 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
42-785C-522-TE
Multiplexer Module
The 40-785C-522-TE (PXI) and 42-785C-522-TE (PXIe) are dual failsafe SP6T 18 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 4-Bank 18GHz SMA
60-801-204
Multiplexer Module
The 60-801-204 is a 6-channel, 4-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 50GHz, 50Ω, SMA-2.4
40-785C-552-T
Multiplexer Module
The 40-785C-552-T (PXI) and 42-785C-552-T (PXIe) are dual SP6T 50GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP8T, 40 GHz, 50 Ω, SMA 2.9, Terminated
42-788-051-T
Multiplexer Module
The 40-788-051-T (PXI) and 42-788-051-T (PXIe) are single SP8T 40 GHz microwave multiplexers with automatic termination of unused signals.
-
Product
LXI Microwave Multiplexer, SP4T, 9-Bank, 18GHz, 50Ω, SMA
60-803-109
Multiplexer Module
Our 60-803-109 is a 9 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
COM Express Rev. 3.1 Basic Size Type 6 Module with 13th Gen Intel® Core™ Mobile Processor
Express-RLP
Computer on Module
ADLINK’s Express-RLP COM Express Type 6 Basic size module is based on 13th Gen Intel® Core™ mobile processor (formerly codenamed Raptor Lake-P) and is the first COM Express utilizing Intel’s advanced hybrid architecture (with up to 6 Performance-cores and 8 Efficient-cores) offered with industrial-grade/real-time option to provide superior performance for edge IoT innovations across varied power ranges — at 15W/28W/45W TDP.
-
Product
PXI Dual SP6T Multiplexer 40GHz 50, SMA-2.9
40-785B-542
Multiplexer Module
The 40-785B-542 is a dual 6-channel 40GHz unterminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
Octal 4 to 1 50 600MHz PXI RF Multiplexer
40-760-008
Multiplexer Module
This octal 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
PXI Single SP6T Multiplexer 26.5GHz 50, SMA-2.9, Terminated
40-785B-531-T
Multiplexer Module
The 40-785B-531 is a single 6-channel 26.5GHz terminated microwave multiplexer. The 40-785B range of multiplexers are available as a single or dual 6-channel panel mounted multiplexer with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 40 GHz, 50 Ω, SMA-2.9, Remote Mount, Failsafe
42-785C-543-E
Multiplexer Module
The 40-785C-543-E (PXI) and 42-785C-543-E (PXIe) are triple failsafe SP6T 40 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP10T, 8 GHz, 50 Ω, N-Type, Remote Mount, Failsafe
40-788-111-E
Multiplexer Module
The 40-788-111-E (PXI) and 42-788-111-E (PXIe) are single failsafe SP10T 8 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
PXI High Density Multiplexer, 4-Bank, 16-Channel, 2-Pole
40-610A-006
Multiplexer Module
The 40-610A-006 is a 4-bank, 16-channel, 2-pole MUX and is part of our range of PXI high density reed-relay based multiplexer modules. The range includes a wide choice of switching configurations which are especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, Terminated, 3GHz, 50Ω, SMB
40-873A-002
Multiplexer Module
The 40-873A-002 (PXI) and 42-873A-002 (PXIe) are 4 to 1 RF multiplexers with 2 banks in a single slot. Additionally, extra switching allows unused channels to be terminated into 50 Ohm, maintaining signal integrity. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
Product
PXI Dual 4 to 1 RF Multiplexer 2GHz 50 Ohm SMB
40-746-511
Multiplexer Module
40-740, 40-745 and 40-746 RF Multiplexers are a range of Bi-Directional Multiplexers with bandwidth up to 2000MHz.They are arranged as Single 8 to 1, Dual 4 to 1 or Single 4 to 1 configurations, all with excellent Insertion Loss, VSWR and Isolation, in 50 Ohm or 75 Ohm versions with a wide choice of connectors.Applications include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching (from 2MBit/s to 155MBit/s), video/audio switching and switching high frequency logic signals.
-
Product
PXIe Microwave Multiplexer, Triple SP4T, 26.5 GHz, 50 Ω, SMA, Remote Mount, Failsafe
42-785C-433-E
Multiplexer Module
The 40-785C-433-E (PXI) and 42-785C-433-E (PXIe) are triple failsafe SP4T 26.5 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
