PCB Adapters
-
Product
Signal, Contact, ITA, QuadraPaddle, Male PCB Pin
610138123
Signal Contact (ITA)
Signal, Contact, ITA, QuadraPaddle, Male PCB Pin.
-
Product
High-Speed Adapter
DDR Pro
-
Introducing the DDR Pro adapter, the latest advanced test adapter for RAMCHECK. This new high-speed DDR test adapter features advanced circuitry and a powerful high-frequency test engine, allowing you to fully test and identify PC433/466 DDR modules, with planned upgrades to 533MHz.
-
Product
X.25 Adapters & XOT
FarSync X25 T4Ee
-
This top of the range FarSync X25 T4Ee PCIe card provides 4 high performance X.25 communications lines handling many different line signalling modes. A PCI version is also available.
-
Product
160-Pin DIN41612 Connector, Right Angle PCB Mount, Female
40-963-160-RF
DIN41612 PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution. Female versions are suited to direct connection to a Pickering Switching Module while male versions can be used to interface to a female cable assembly termination.
-
Product
Supply Adapters
AP Series
-
*Overflow Relative Noise Temperature and Return Loss Measurement within all Frequency Range*Ultrawide Frequency Range*Small Size*4 Design Structures with Different Connector Types
-
Product
High-Stability Adapter
10723A
Accessory Kit
The Keysight 10723A high-stability adapter converts the 10706A Plane Mirror Interferometer into an 10706B High-Stability Plane Mirror Interferometer. The 10706B is a thermally-stable optic with measurement drift reduced to approximately 1/12 the value achieved by conventional plane mirror interferometers.
-
Product
DB9 To Twinax Adapter
DB9TWX67
-
The DB9TWX67 is an adapter for converting the DB9 outputs of ANDOR Design’s MIL-STD-1553 cards to the Twin Axial connector used in MIL-STD-1553. Two adapters are supplied with each dual redundant channel card.
-
Product
PCB repair / rework station
XJInvestigator
-
Much more than a production line test tool, XJInvestigator is a repair focused, integrated test and debug environment for fault analysis, helping you efficiently recover your failing boards.
-
Product
Control Board For Testing PCBs
TCC 1800
-
The TCC1800 Test Controller Card is a generic control board for production testing of printed circuit boards (PCBs). The board is controlled by a command language on a PC to which it is connected via a galvanically separated USB interface. The TCC1800 is designed to work with positive voltages up to 24V. All inputs and outputs are protected against higher voltages however. The card provides basic IO: Analog and digital interfacing, counters, PWM outputs, bidirectional I/O, Serial (UART) and I2C interfacing.
-
Product
Adapter
P350NM75NF
-
P350NM75NF Adapter, Frequency Range: Up to 12 GHz, Impedance: 50 Ohm to 75 Ohm
-
Product
Pulse Adapter
CV30P650
-
Frothingham Electronics Corporation
The CV30 P650 test station is currently the highest voltage pulser in a series of exponential pulse generators that can be connected to our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. The CV30 P650 pulse adapter can produce a maximum current of 100A at up to 600V using exponential pulses up the 10/1000 waveform. The pulser is rated at 30KW from 300V to 650V. Voltage compliance at 100A is 600V. The station can also include all of the usual FEC200 tests in the same test program.
-
-
Product
Off-Card Adapter,
3910-FOFE
-
As the physical size of Fibre Optic Front End (FOFE) transceivers prohibits their use on PCI, CompactPCI, PMC and ISA (PC/AT) cards, Western Avionics provides an off-card Adapter, that contains all components to support the 3910 Optical implementation of STANAG 3910. The 3910-FOFE Adapter provides a complete dual redundant optical interface, together with dual redundant 3838 connections, and Trigger-in and Trigger-out in a minimal sized package, to allow convenient cabling connections to the 3910 / 3838 system or unit-under-test.
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
Test System
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
Product
Protective Cover, G20x, Receiver, 6.75" Series Adapters
310113597
Protective Cover
Protective Cover, G20x, Receiver, 6.75" Series Adapters
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type H, Ø0.80mm, 155gf
K100-H080155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style H, Tip Diameter Ø0.80mm, Spring force 155gf, Steel with Gold Plating.
-
-
Product
UXG X-Series Agile Vector Adapter, 50 MHz to 20 GHzNEW!
N5194A
Vector Baseband Generator
The N5194A is part of the UXG family of signal generation products designed for threat simulation; simulate complex signal environments for radar/EW.
-
Product
XMC-to-PCI Express (PCIe) Adapter
8615
-
The Technobox, Inc. P/N 8615 XMC-to-PCI Express adapter with Rear I/O support permits use of a standard VITA 42.3 air-cooled XMC, or VITA 20 conduction-cooled XMC, in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC, and 10 mm mezzanine stacking height is supported. The height is a standard PCI Express board, and is not the low-profile version.
-
Product
PCIe Adapter for XMC
PCIe8LXMCX2
-
Embedded applications frequently require real time processing coupled with special purpose IO. With the PCIe8LXMCX2´s two positions a PrXMC can be matched with another XMC to make a high bandwidth processing node. The PrXMC can communicate with the host for set-up, and then use the switch to interconnect with the special purpose IO card.
-
Product
32-bit PMC to PCI Adapter
8092
-
This PMC to PCI Adapter permits delivery of PMC-derived applications in a standard PCI environment. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications.
-
Product
PSS PCB Tester
MS 1106
-
PSS PCB Tester is a powerful system used to test and validate DAWN (RWR & JAMMER) Support System boards. It has RS232/USB Communication for PC Interface.
-
Product
Basic 3U VPX-to-PCI Express (PCIe/PCI-e) Adapter
8464
-
The Technobox, Inc P/N 8464 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths.
-
Product
MTB Calibration Adapter
2450-CAL-30
-
The MTB Calibration Adapter (Catalog No. 2450-CAL-30)is a socket adapter that’s designed to bring phase A, B, and C current and potentials of a TESCO Multi-Position Test Board to an external RD-30 reference standard for calibration of the Test Board.
-
Product
EBIRST 104-pin D-type To 96-pin SCSI Adapter Cable
93-022-226
Adapter Cable
The 93-002-226 104-pin to 96-pin eBIRST adapter cable is part of a range of USB controlled test tools capable of performing automated path resistance tests on Pickering Interfaces PXI, LXI or PCI controlled switching solutions. Each tool simply interfaces with the switching system's connector so a test can be run using the supplied Windows-based software.
-
Product
Adapter, 2.4 mm (m) to 2.4 mm (m), DC to 50 GHz
11900A
Coax Adapter
The Keysight 11900A is a metrology-grade, 2.4 mm male to 2.4 mm male adapter with dc to 50 GHz operation.
-
-
-
Product
PCIe-to-MXM adapter supporting ADLINK Mobile PCI Express Modules with NVIDIA® Quadro® embedded GPUs
EGX-MXM-AD
PXI Express Module
The EGX-MXM-AD is an PCIe adapter supporting ADLINK NVIDIA® Quadro® MXM 3.1 Type A, Type B, and Type B+ GPU modules for quick validation and early development purposes on your AI applications. The following modules are supported: EGX-MXM-P1000, EGX-MXM-P2000, EGX-MXM-T1000, EGX-MXM-RTX3000, and EGX-MXM-RTX5000. A reference thermal solution is available.
-
Product
3-Pin Power D-Type Connector, 40A, Female PCB Mount
40-963-003-RF
D-Sub PCB-Mount Connector
This connector is suitable for Pickering Interface's modules that use the 3-Pin Power D-Type connector. It is designed to allow users to make a termination via a PCB.
