PCB Adapters
-
Product
Positional Current Probe, PCB Track Touch And Measure
I-prober 520
-
Current measurement from insulated probing of conductorSuitable for observation and measurement of current in PCB tracks, component leads and ground planesWide dynamic range of 10mA to 20A peak to peakWide bandwidth of DC to 5MHzLow noise figure equivalent to <6mA rms at full B/WSafety rated to 300V Cat II (600V Cat 1)Suitable for connection to any oscilloscopeHigh accuracy general purpose H-field probeConverts to 'closed magnetic circuit' current probe
-
Product
Basic 3U VPX-to-PCI Express (PCIe/PCI-e) Adapter
8462
-
The Technobox, Inc. P/N 8462 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths. When seated in a PC motherboard, the VPX card primary side faces upward to allow convenient access to components.
-
Product
DH Series QuickLink Adapter, 8 GHz BW
DH-QL
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Power Line EMI Adapters
-
How much EMI noise is on your power lines indeed? How to assess the levels of noise and its properties when it is obviously a bad idea to connect your oscilloscope or a spectrum analyzer directly to your power lines?Our EMI interface adapters provide a barrier for high mains voltages but a straight passage for high-frequency signals so that you can connect your sensitive instrument to power lines for analysis and quantification. We offer plug-in and hand-held adapters which can measure both differential ("normal") and common-mode noise.
-
Product
PCB Test Points and Terminals
-
Our PCB test points and terminals feature a large loop for easy probe attachment or to facilitate the clipping on of other components. They are ideal for components which need frequent replacement and are also suitable for raising hot components above the surface of the PCB.
-
Product
ECM PCB Tester
MS 1105
-
*Used for testing of DAWN RWR PCBs in Jaguar Aircraft*19” Rack mountable with built-in wide range of IO signals *Used in 4th line servicing of PCBs*Used in LRU and system level testing*Detects 100% fault coverage including track faults*Adaptability with off-the-shelf instruments
-
Product
NI-6585, 200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO
781071-01
Digital I/O Adapter
200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO—The NI-6585 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 32 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6585 can operate at up to 200 MHz clock rates and includes support for common LVDS voltages.
-
Product
Calibration Hex Step Adapters
-
When performing torque wrench calibration or testing, adapters are often needed, especially with torque wrenches that have open-end heads. Mountz’s calibration hex step adapter features four common sizes, which will increase the productivity of your torque wrench calibration process. This adapter will make testing and calibration simple and efficient.
-
Product
Waveguide to Coaxial Adapter
DAWC-18-40G-2.92K
-
Waveguide to Coaxial Adapter, Frequency 18~40GHz, 50W, Double Ridged Waveguide WRD180C24, 2.92mm Female
-
Product
Adapters
-
Amphenol Fiber Systems International
Amphenol Fiber Systems International (AFSI) offers a complete suite of passive fiber optic adapters to facilitate conversion from one network-based connector type to another. The small size of these adapters eliminates the need for bulky and expensive adapter cables.
-
Product
Adapter for 980L-1A Tester
TA-331A
-
331A-9G HSI Adapter for use with the 980L-1A tester. Built to manufacturer's specs to allow by the book testing.
-
-
Product
Electric Vehicle Charging Station EVSE Test Adapter
FEV100
-
Test the safety and performance of a type 1, level 1 or level 2 electric vehicle ac charging stations (EVSEs) with the Fluke FEV100. This test adapter simulates the presence of an electrical vehicle, allowing you to conduct tests in combination with appropriate test instruments such as a digital multimeter or oscilloscope.
-
-
Product
U1180A Thermocouple Adapter And Lead Kit, J And K Types
-
The Keysight U1180A thermocouple adapter and lead set are compatible with all series of Keysight Handheld Digital Multimeters. The set includes a J/K type Thermocouple adapter, thermocouple bead J-type and a thermocouple bead K-type.
-
Product
Vacuum Test Adapter
-
Vacuum test adapters (VA) are suitable for contacting electronic assemblies with large quantities (mass testing) and a small number of variants. INGUN vacuum test adapters are available as standard as a single system without an exchangeable replacement kit.
-
Product
26-Pin D-Type Male Straight PCB Mount
40-963-026-SM
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
COM Express Type 7 10GbE SFP+ Network Adapter Card
CEI-2x10G SFP+
Network Interface Controller
- Support up to two 10GbE SFP+ interfaces- Inphi CS4227 inside- COM.0 R3.1 Type 7 compliant- Dedicated for Express-VR7
-
Product
32/64 Bit 33/66 MHz PCI-X to PMC-X Adapter
4044
-
32/64 Bit 33/66 MHz PCI-X to PMC-X Adapter. The PCI-X to PMC-X Adapter permits operation of a standard 32 or 64 bit PCI-X card in a PMC-X slot. It provides a migration path for PCI-X board suppliers to port their products to a PMC-X form factor. As the PMCX equivalent board is developed, software development and migration can proceed with the original PCI-X board operating in a PMC-X environment.
-
Product
96-Pin SCSI Micro-D Right-Angle PCB
40-963-096-RM
SCSI Male PCB Mount
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Coax, Contact, Receiver and ITA, 40 GHz
610102114
Contact Adapter (Receiver/ITA)
The 40 GHz Coax contact is a blind mate connector that mates with 3.5 mm and 2.92 mm connectors. It is recommended to use 2.92 mm connectors for frequencies above 35 GHz.
-
Product
Protective Cover, G20, 6.75" Series Adapters, Receiver
310113422
Protective Cover
Protective Cover, G20, 6.75" Series Adapters, Receiver
-
Product
Passive XMC-to-PCI Express Adapter
5934
-
The Technobox, Inc. P/N 5934 is designed to adapt a single-wide XMC card to a 4X PCI Express slot. The 5934 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
Product
Relay Buddy Adapter Set
190-4
-
*Expands the testing capability of your Relay Buddy! *3 pack of adapters allows testing of shielded relays, same relays tested by #190 Relay Buddy *Relay adapter plugs into Relay Buddy first *Shielded relay then plugs into the top of the adapter
-
Product
8-Port RS232 Async Serial Communications Adapter PMC
2229
-
The Technobox 8-Port Async Communication adapter provides eight 16550-based UARTs using RS232 signaling levels. Each port provides the full set of data and modem control lines configured for DTE
-
Product
1.85mm Adapters
-
Pasternack 1.85mm adapter category majority are RoHS and REACH compliant. 1.85mm adapter components are part of a comprehensive adapter product line from Pasternack.Our 1.85mm adapters allow you to interface 1.85mm connectors with 1.85mm, 2.4mm, 2.92mm, 3.5mm, N, SMA or SSMA connectors. 1.85mm adapters are constructed in female to female, female to male, male to female or male to male gender designs.Pasternack's ISO 9001:2008 registered facility ships 1.85mm adapter series the same day from the broadest and deepest in stock inventory of microwave and RF parts. Excellent technical support and customer service are on hand to assist you.
-
Product
Pull-Thru Adapters
-
VPC offers a selection of pull-thru adapters to meet PXI connection needs. Pull-thru adapters consolidate wiring for wired connections and provide a seamless connection to the card for PCB needs.
-
Product
Signal, Module, ID, CASS, 64 Position, Center PCB Mount
510114109
ITA Module
Signal, Module, ID, CASS, 64 Position, Center PCB Mount
-
Product
50-Pin Ribbon Conn Straight PCB Mount
40-963-550-SM
IDC Male Connector
Ideal for user created termination schemes where the termination is to be remotely connected to the module by cable. Interfacing PCBs should be designed with suitable clearances for the working voltage the application requires.
-
Product
Auto Reversing Run Down Adapters
AURA
-
The AURA auto reversing run down adapters are designed to provide consistent and reliable torque readings for use with power driven torque control tools. The AURA reduces the impact and irregular peaks that cause poor repeatability. The run down adapter is mounted in-line between the tool drive and transducer.
